Visible to Intel only — GUID: yfi1683015148773
Ixiasoft
1. GTS Transceiver Overview
2. GTS Transceiver Architecture
3. Implementing the GTS PMA/FEC Direct PHY Intel FPGA IP
4. Implementing the GTS System PLL Clocks Intel FPGA IP
5. Implementing the GTS Reset Sequencer Intel FPGA IP
6. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
7. Design Assistance Tools
8. Debugging GTS Transceiver Links with Transceiver Toolkit
9. Document Revision History for the GTS Transceiver PHY User Guide
3.1. IP Overview
3.2. Designing with the GTS PMA/FEC Direct PHY Intel FPGA IP
3.3. Configuring the GTS PMA/FEC Direct PHY Intel FPGA IP
3.4. Signal and Port Reference
3.5. Bit Mapping for PMA and FEC Mode PHY TX and RX Datapath
3.6. Clocking
3.7. Custom Cadence Generation Ports and Logic
3.8. Asserting reset
3.9. Bonding Implementation
3.10. Configuration Register
3.11. Configuring the GTS PMA/FEC Direct PHY Intel FPGA IP for Hardware Testing
3.12. Configurable Quartus® Prime Software Settings
3.13. Hardware Configuration Using the Avalon® Memory-Mapped Interface
3.4.1. TX and RX Parallel and Serial Interface Signals
3.4.2. TX and RX Reference Clock and Clock Output Interface Signals
3.4.3. Reset Signals
3.4.4. FEC Signals
3.4.5. PCS Direct Signals: IEEE
3.4.6. PCS Direct Signals: IEEE_FLEXE_66/PCS66
3.4.7. Custom Cadence Control and Status Signals
3.4.8. RX PMA Status Signals
3.4.9. TX and RX PMA and Core Interface FIFO Signals
3.4.10. Avalon Memory-Mapped Interface Signals
3.8.1. Reset Signal Requirements
3.8.2. Power On Reset Requirements
3.8.3. Reset Signals—Block Level
3.8.4. Run-time Reset Sequence—TX
3.8.5. Run-time Reset Sequence—RX
3.8.6. Run-time Reset Sequence—TX + RX
3.8.7. Run-time Reset Sequence—TX with FEC
3.8.8. RX Data Loss/CDR Lock Loss (Auto-Recovery)
3.8.9. TX PLL Lock Loss
6.1. Instantiating the GTS PMA/FEC Direct PHY Intel FPGA IP
6.2. Generating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
6.3. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Functional Description
6.4. Simulating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Testbench
6.5. Compiling the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
6.6. Hardware Testing the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
Visible to Intel only — GUID: yfi1683015148773
Ixiasoft
3.8.5. Run-time Reset Sequence—RX
Figure 55. Run-time Reset Sequence—RX
The figure above illustrates the following run-time RX reset sequence:
- Assert i_rx_reset.
- o_rx_ready deasserts, indicating that the RX datapath is no longer operational.
- o_rx_is_lockedtoref and o_rx_is_lockedtodata deasserts.
- o_rx_reset_ack asserts, indicating that the RX datapath is fully in reset. o_rx_reset_ack stays asserted until i_rx_reset deasserts.
- You then deassert i_rx_reset to bring RX out of reset.
- o_rx_is_lockedtoref asserts as the CDR locks to the reference clock.
- o_rx_is_lockedtodata asserts as the CDR locks to the recovered data.
- o_rx_ready asserts.
Note: o_rx_is_lockedtoref and o_rx_is_lockedtodata may have different behavior in simulation.