GTS Transceiver PHY User Guide

Download PDF
ID 817660
Date 7/08/2024
Public
Document Table of Contents
Document Table of Contents x
1. GTS Transceiver Overview 2. GTS Transceiver Architecture 3. Implementing the GTS PMA/FEC Direct PHY Intel FPGA IP 4. Implementing the GTS System PLL Clocks Intel FPGA IP 5. Implementing the GTS Reset Sequencer Intel FPGA IP 6. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design 7. Design Assistance Tools 8. Debugging GTS Transceiver Links with Transceiver Toolkit 9. Document Revision History for the GTS Transceiver PHY User Guide
2. GTS Transceiver Architecture x
2.1. Building Blocks 2.2. Channel Placement Rules and Design Requirements 2.3. PMA Architecture 2.4. PCS Architecture 2.5. Forward Error Correction (FEC) Architecture 2.6. Clock Architecture 2.7. Bonding and Deskew
2.1. Building Blocks x
2.1.1. PMA 2.1.2. FEC 2.1.3. PCS 2.1.4. Ethernet MAC 2.1.5. PCI Express* Hard IP 2.1.6. PLL and Clock Networks 2.1.7. Avalon® Memory-Mapped Interface
2.2. Channel Placement Rules and Design Requirements x
2.2.1. Hard IP Rules 2.2.2. Use Scenario Rules 2.2.3. Unused PMA Rules 2.2.4. General Design Requirement
2.3. PMA Architecture x
2.3.1. Transmitter PMA Architecture 2.3.2. Receiver PMA Architecture 2.3.3. PMA Loopback Modes
2.3.1. Transmitter PMA Architecture x
2.3.1.1. Transmitter Buffer 2.3.1.2. Serializer 2.3.1.3. Data Pattern Generator and Verifier
2.3.2. Receiver PMA Architecture x
2.3.2.1. Receiver Buffer and Equalizer 2.3.2.2. Deserializer 2.3.2.3. CDR Block 2.3.2.4. PMA Tuning
2.3.2.1. Receiver Buffer and Equalizer x
2.3.2.1.1. Control Unit
2.5. Forward Error Correction (FEC) Architecture x
2.5.1. FEC Loopback Mode
2.6. Clock Architecture x
2.6.1. Reference Clock Network 2.6.2. Datapath Clock Network 2.6.3. System PLL 2.6.4. Datapath Clock Cadences 2.6.5. Shared Clocking Resources Between the GTS Transceiver Bank and HVIO Bank
2.6.1. Reference Clock Network x
2.6.1.1. Single GTS Transceiver Bank Device 2.6.1.2. PMA Primary PLL Configuration
2.6.3. System PLL x
2.6.3.1. I/O PLLs in HVIO Bank as System PLL 2.6.3.2. Running PCIe* and Non- PCIe* Protocols in a GTS Transceiver Bank 2.6.3.3. System PLL Clock for FPGA Core 2.6.3.4. System PLL with HVIO Reference Clock
2.7. Bonding and Deskew x
2.7.1. Bonding Architecture 2.7.2. TX Deskew Function
3. Implementing the GTS PMA/FEC Direct PHY Intel FPGA IP x
3.1. IP Overview 3.2. Designing with the GTS PMA/FEC Direct PHY Intel FPGA IP 3.3. Configuring the GTS PMA/FEC Direct PHY Intel FPGA IP 3.4. Signal and Port Reference 3.5. Bit Mapping for PMA and FEC Mode PHY TX and RX Datapath 3.6. Clocking 3.7. Custom Cadence Generation Ports and Logic 3.8. Asserting reset 3.9. Bonding Implementation 3.10. Configuration Register 3.11. Configuring the GTS PMA/FEC Direct PHY Intel FPGA IP for Hardware Testing 3.12. Configurable Quartus® Prime Software Settings 3.13. Hardware Configuration Using the Avalon® Memory-Mapped Interface
3.1. IP Overview x
3.1.1. PMA Direct Supported Modes 3.1.2. FEC Direct Supported Modes 3.1.3. PCS Direct Supported Modes 3.1.4. Unsupported PMA/FEC/PCS Modes
3.3. Configuring the GTS PMA/FEC Direct PHY Intel FPGA IP x
3.3.1. Preset IP Parameter Settings 3.3.2. Common Datapath Options 3.3.3. TX Datapath Options 3.3.4. RX Datapath Options 3.3.5. FEC Options 3.3.6. PCS Options 3.3.7. Avalon® Memory-Mapped Interface Options 3.3.8. Register Map IP-XACT Support 3.3.9. Analog Parameter Options
3.3.3. TX Datapath Options x
3.3.3.1. TX PMA Interface Parameters
3.3.4. RX Datapath Options x
3.3.4.1. RX PMA Interface Parameters
3.4. Signal and Port Reference x
3.4.1. TX and RX Parallel and Serial Interface Signals 3.4.2. TX and RX Reference Clock and Clock Output Interface Signals 3.4.3. Reset Signals 3.4.4. FEC Signals 3.4.5. PCS Direct Signals: IEEE 3.4.6. PCS Direct Signals: IEEE_FLEXE_66/PCS66 3.4.7. Custom Cadence Control and Status Signals 3.4.8. RX PMA Status Signals 3.4.9. TX and RX PMA and Core Interface FIFO Signals 3.4.10. Avalon Memory-Mapped Interface Signals
3.6. Clocking x
3.6.1. Clock Ports 3.6.2. Recommended tx/rx_coreclkin Connection and tx/rx_clkout2 Source 3.6.3. Port Widths and Recommended Connections for tx/rx_coreclkin, tx/rx_clkout, and tx/rx_clkout2 3.6.4. PMA Fractional Mode
3.7. Custom Cadence Generation Ports and Logic x
3.7.1. Enabling the i_tx_cadence_slow_clk_locked Port
3.8. Asserting reset x
3.8.1. Reset Signal Requirements 3.8.2. Power On Reset Requirements 3.8.3. Reset Signals—Block Level 3.8.4. Run-time Reset Sequence—TX 3.8.5. Run-time Reset Sequence—RX 3.8.6. Run-time Reset Sequence—TX + RX 3.8.7. Run-time Reset Sequence—TX with FEC 3.8.8. RX Data Loss/CDR Lock Loss (Auto-Recovery) 3.8.9. TX PLL Lock Loss
3.9. Bonding Implementation x
3.9.1. Bonding Placement Requirements
3.10. Configuration Register x
3.10.1. GTS PMA and FEC Direct PHY Soft CSR Register Map 3.10.2. GTS PMA Register Map 3.10.3. Accessing Configuration Registers
3.10.2. GTS PMA Register Map x
3.10.2.1. Logical Avalon® Memory-Mapped Port Indexing
3.10.3. Accessing Configuration Registers x
3.10.3.1. Accessing GTS PMA and FEC Direct PHY Soft CSR Registers 3.10.3.2. Accessing GTS PMA Registers
3.11. Configuring the GTS PMA/FEC Direct PHY Intel FPGA IP for Hardware Testing x
3.11.1. Using Debug Endpoint Interface within the GTS PMA/FEC Direct PHY Intel FPGA IP 3.11.2. Using JTAG to Avalon Master Bridge Intel FPGA IP
3.11.1. Using Debug Endpoint Interface within the GTS PMA/FEC Direct PHY Intel FPGA IP x
3.11.1.1. RTL Connection Example for Debug Endpoint Avalon® Interface
3.11.2. Using JTAG to Avalon Master Bridge Intel FPGA IP x
3.11.2.1. RTL Connection Example for JTAG to Avalon Master Bridge Intel® FPGA IP
3.13. Hardware Configuration Using the Avalon® Memory-Mapped Interface x
3.13.1. Direct Register Method 3.13.2. GTS Attribute Access Method
3.13.1. Direct Register Method x
3.13.1.1. Direct Register Method Examples
3.13.2. GTS Attribute Access Method x
3.13.2.1. GTS Attribute Access Method Example 1 3.13.2.2. GTS Attribute Access Method Example 2
4. Implementing the GTS System PLL Clocks Intel FPGA IP x
4.1. IP Parameters 4.2. IP Port List 4.3. Mode of System PLL - System PLL Reference Clock and Output Frequencies 4.4. Guidelines for GTS System PLL Clocks Intel FPGA IP Usage 4.5. Guidelines to Indicate System PLL Reference Clock is Ready
4.5. Guidelines to Indicate System PLL Reference Clock is Ready x
4.5.1. Example Flow to Indicate System PLL Reference Clock is Ready
5. Implementing the GTS Reset Sequencer Intel FPGA IP x
5.1. IP Requirements 5.2. IP Parameters 5.3. IP Port List 5.4. GTS Reset Sequencer Intel FPGA IP General Interface 5.5. GTS Reset Sequencer Intel FPGA IP Design Flow 5.6. GTS Reset Sequencer Intel FPGA IP Use Cases
5.6. GTS Reset Sequencer Intel FPGA IP Use Cases x
5.6.1. Example Use Case 1 5.6.2. Example Use Case 2
6. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design x
6.1. Instantiating the GTS PMA/FEC Direct PHY Intel FPGA IP 6.2. Generating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design 6.3. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Functional Description 6.4. Simulating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Testbench 6.5. Compiling the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design 6.6. Hardware Testing the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
6.2. Generating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design x
6.2.1. Fast Simulation Support 6.2.2. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Directory Structure
6.4. Simulating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Testbench x
6.4.1. Modifying the Example Design and Performing Simulation
7. Design Assistance Tools x
7.1. Clocking and Datapath Tool 7.2. TX Equalizer Tool
8. Debugging GTS Transceiver Links with Transceiver Toolkit x
8.1. GTS Transceiver Toolkit Parameter Settings 8.2. GTS Transceiver Toolkit GUI 8.3. GTS Transceiver Debugging Flow Walkthrough
8.2. GTS Transceiver Toolkit GUI x
8.2.1. Collection View
8.3. GTS Transceiver Debugging Flow Walkthrough x
8.3.1. Modifying the Design to Enable GTS Transceiver Debug Toolkit 8.3.2. Programming the Design into an Intel FPGA 8.3.3. Loading the Design to the Transceiver Toolkit 8.3.4. Creating Transceiver Links 8.3.5. Running BER Tests 8.3.6. Running Eye Viewer Tests 8.3.7. Running Link Optimization Tests
1. GTS Transceiver Overview
2. GTS Transceiver Architecture
3. Implementing the GTS PMA/FEC Direct PHY Intel FPGA IP
4. Implementing the GTS System PLL Clocks Intel FPGA IP
5. Implementing the GTS Reset Sequencer Intel FPGA IP
6. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
7. Design Assistance Tools
8. Debugging GTS Transceiver Links with Transceiver Toolkit
9. Document Revision History for the GTS Transceiver PHY User Guide

5.5. GTS Reset Sequencer Intel FPGA IP Design Flow

The design flow for the GTS Reset Sequencer Intel FPGA IP is described below:
  1. Add the GTS Reset Sequencer Intel FPGA IP from the IP Catalog into your design as shown in the following figure.
    Figure 76. IP Catalog
  2. Select the total Number of Bank(s) that you want to use for the GTS Reset Sequencer Intel FPGA IP as shown in the following figure.
    Figure 77. IP Parameters for Bank Selection
  3. Select the total Number of Reset Sequencer Lane(s) that you want to use for the GTS Reset Sequencer Intel FPGA IP as shown in the following figure.
    Figure 78. IP Parameters for Lane Selection
  4. Connect o_src_rs_grant and i_src_rs_req to the channels. The o_src_rs_grant and i_src_rs_req must be connected to the same channel so that the reset operation works accordingly. For simplex applications, each simplex PMA occupies one channel; therefore, it needs its own o_src_rs_grant and i_src_rs_req signals.
    Note: For dual-simplex mode, you must connect each RX and TX channel to the same o_src_rs_grant and i_src_rs_req signals.
  5. Connect o_pma_cu_clk to i_pma_cu_clk input of the GTS PMA/FEC Direct PHY Intel FPGA IP and protocol IPs. If there are two or more IPs in the same bank, the IPs must be connected to the same o_pma_cu_clk. For any separate bank, make sure to use different o_pma_cu_clk for each bank.
    Note: There is no order requirement for the o_pma_cu_clk signal.
  6. For channels that need to be prioritized for reset sequencing, tie i_src_rs_priority to 1 for that specific channel based on the connection of bits o_src_rs_grant and i_src_rs_req for that channel. For non-priority (normal) reset sequence channels, tie the i_src_rs_priority to 0. For example, the value 4’b0010, sets the priority to lane 2.
Note: You can skip steps 3. 4, and 6. if you set the Enable PCIE and/or HPS USB3.1 only design option to Enable in the IP parameter GUI, since the parameters and ports are unavailable. If you are using Platform Designer, for steps 4 and 5, you must connect o_src_rs_grant, i_src_rs_req, and o_pma_cu_clk signals using wire-level expressions. Refer Editing Wire-Level Expressions in the Quartus® Prime Pro Edition User Guide: Platform Designer for more details.
Level Two Title