MACsec Intel FPGA System Design User Guide

Download PDF
ID 767516
Date 6/26/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Introduction 2. Architecture 3. Interface Overview 4. Parameters 5. Configuration Registers 6. Software Architecture 7. Generating the System Design 8. Document Revision History for MACsec System Design User Guide A. Release Notes
1. Introduction x
1.1. Terminology 1.2. Release Information 1.3. System Requirements
2. Architecture x
2.1. System Architecture 2.2. Data Path Between Ethernet MAC and MACsec 2.3. Data Path Between MACsec and MCDMA 2.4. Data Path Between MACsec and Packet Generator/Checker (Packet Client) 2.5. Data Path Illustrations 2.6. Interrupts 2.7. Packet FIFO 2.8. AXI-ST Rate Controller 2.9. Error Handling 2.10. Top Level Signals
2.2. Data Path Between Ethernet MAC and MACsec x
2.2.1. Ethernet Subsystem
2.2.1. Ethernet Subsystem x
2.2.1.1. Data Receiving from MACsec to E/F-Tile Hard IP 2.2.1.2. Data Transmitting from E/F-tile Hard IP to MACsec 2.2.1.3. Order of Ethernet Transmission 2.2.1.4. E/F-Tile Hard IP Reset Sequence
2.3. Data Path Between MACsec and MCDMA x
2.3.1. AXI-ST Multi-Segment to Single-Segment Conversion 2.3.2. MCDMA
2.4. Data Path Between MACsec and Packet Generator/Checker (Packet Client) x
2.4.1. Packet Client 2.4.2. Packet Generation and Check
2.5. Data Path Illustrations x
2.5.1. MACsec Interface Signal Names
2.6. Interrupts x
2.6.1. MCDMA MSI-X Table Configuration
3. Interface Overview x
3.1. Clocking 3.2. Resets
5. Configuration Registers x
5.1. System Register Map
5.1. System Register Map x
5.1.1. Packet Client Register Map 5.1.2. Interrupt Controller Register Map
6. Software Architecture x
6.1. MACsec Key Agreement Protocol 6.2. Driver Functional Requirements 6.3. Software Requirements 6.4. Software Overview 6.5. MACsec IP APIs Sequence 6.6. Functions 6.7. Software Tools
6.4. Software Overview x
6.4.1. McDMA Driver Kernel Module 6.4.2. MACsec IP APIs 6.4.3. Linux MACsec Driver Kernel Module 6.4.4. IP Tool 6.4.5. WPA Supplicant
6.4.2. MACsec IP APIs x
6.4.2.1. SDK
6.5. MACsec IP APIs Sequence x
6.5.1. MACsec Initialization Sequence
6.5.1. MACsec Initialization Sequence x
6.5.1.1. MACsec Reset Sequence 6.5.1.2. TX Configuration Sequence 6.5.1.3. RX Configuration Sequence 6.5.1.4. TX Rekeying Sequence 6.5.1.5. RX Rekeying Sequence 6.5.1.6. Cut Through/Store Forward Mode 6.5.1.7. User Single/Multi Port Settings 6.5.1.8. Encrypt/Decrypt Port 6.5.1.9. Port Priority 6.5.1.10. Interrupt Generation and Register
6.5.1.1. MACsec Reset Sequence x
6.5.1.1.1. GLOBAL Reset 6.5.1.1.2. PORT Reset 6.5.1.1.3. Secure Association (SA) Reset
6.6. Functions x
6.6.1. macsec_initilize 6.6.2. macsec_get_attributes 6.6.3. macsec_get_sa_attributes 6.6.4. macsec_set_attributes 6.6.5. macsec_set_sa_attributes 6.6.6. macsec_read_register 6.6.7. macsec_write_register 6.6.8. macsec_set_port_configuration 6.6.9. macsec_rate_configuration 6.6.10. macsec_single_or_multi_port 6.6.11. macsec_crypto_mode 6.6.12. macsec_port_priority 6.6.13. macsec_register_isr
6.7. Software Tools x
6.7.1. IP Tool 6.7.2. WPA_Supplicant 6.7.3. CLI Debug Tool
6.7.3. CLI Debug Tool x
6.7.3.1. Functional Requirements 6.7.3.2. Features Overview 6.7.3.3. Design with HOST 6.7.3.4. Netlink Interface 6.7.3.5. SDK 6.7.3.6. Design Overview
7. Generating the System Design x
7.1. Software Requirements 7.2. Obtaining the Reference Design 7.3. Reference Design Directory Structure 7.4. Simulation Command Arguments 7.5. Simulation Test Cases 7.6. Complete Simulation Command 7.7. Simulation Requirements 7.8. Running Non-UVM Simulation 7.9. Running UVM Simulation 7.10. Building, Installing, and Running the Software 7.11. Building the Hardware Design
7.4. Simulation Command Arguments x
7.4.1. Simulation -d Options
1. Introduction
2. Architecture
3. Interface Overview
4. Parameters
5. Configuration Registers
6. Software Architecture
7. Generating the System Design
8. Document Revision History for MACsec System Design User Guide
A. Release Notes

6.5.1.2. TX Configuration Sequence

Figure 36. MACSEC set_attr() and set_sa_attr() Flows
Figure 37. MACSEC get_attr() and get_sa_attr() Flows
Figure 38. MACsec TX Configuration Attributes
Do the following:
  • Set the Tx basic configuration for the MACsec instance for the port.
  • Set the packet numbering limit value for the MACsec instance.
  • Set the maximum packet bytes supported value for the MACsec instance.
  • Set SCI value for the port.
  • Choose a security association and program the following configuration:
    • Set the rx Key value for the SA.
    • Set the next packet number value for the SA.
    • Set the confidentiality offset value for the SA.
    • Initialize all the stat configurations.
  • Set the “SA Enable” value to the chosen security association.
  • Set “Control port enable” to True for the port.
Level Two Title