F-Tile Triple-Speed Ethernet Intel® FPGA IP User Guide

Download PDF
ID 741328
Date 2/09/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the F-Tile Triple Speed Ethernet Intel FPGA IP User Guide 2. About This IP 3. Getting Started 4. Parameter Settings 5. Functional Description 6. Configuration Register Space 7. Interface Signals 8. Design Considerations 9. Timing Constraints 10. Software Programming Interface 11. Document Revision History for the F-tile Triple-Speed Ethernet Intel® FPGA IP User Guide A. Ethernet Frame Format B. Simulation Parameters
2. About This IP x
2.1. Release Information 2.2. Device Family Support 2.3. Features 2.4. 10/100/1000 Ethernet MAC Versus Small MAC 2.5. High-Level Block Diagrams 2.6. Example Applications 2.7. IP Verification 2.8. Performance and Resource Utilization
2.7. IP Verification x
2.7.1. Optical Platform 2.7.2. Copper Platform
3. Getting Started x
3.1. Introduction to Intel® FPGA IP Cores 3.2. Installing and Licensing Intel® FPGA IPs 3.3. Specifying the IP Core Parameters and Options 3.4. IP Core Generation Output 3.5. Simulating Intel® FPGA IP Cores
3.2. Installing and Licensing Intel® FPGA IPs x
3.2.1. Intel® FPGA IP Evaluation Mode
3.4. IP Core Generation Output x
3.4.1. Design Constraint File
4. Parameter Settings x
4.1. Core Configuration 4.2. Ethernet MAC Options 4.3. FIFO Options 4.4. PCS/Transceiver Options
5. Functional Description x
5.1. 10/100/1000 Ethernet MAC 5.2. 1000BASE-X/SGMII PCS With Optional Embedded PMA
5.1. 10/100/1000 Ethernet MAC x
5.1.1. MAC Architecture 5.1.2. MAC Interfaces 5.1.3. MAC Transmit Datapath 5.1.4. MAC Receive Datapath 5.1.5. MAC Transmit and Receive Latencies 5.1.6. FIFO Buffer Thresholds 5.1.7. Congestion and Flow Control 5.1.8. Magic Packets 5.1.9. MAC Local Loopback 5.1.10. MAC Reset 5.1.11. PHY Management (MDIO) 5.1.12. Connecting MAC to External PHYs
5.1.3. MAC Transmit Datapath x
5.1.3.1. IP Payload Re-alignment 5.1.3.2. Address Insertion 5.1.3.3. Frame Payload Padding 5.1.3.4. CRC-32 Generation 5.1.3.5. Interpacket Gap Insertion 5.1.3.6. Collision Detection in Half-Duplex Mode
5.1.4. MAC Receive Datapath x
5.1.4.1. Preamble Processing 5.1.4.2. Collision Detection in Half-Duplex Mode 5.1.4.3. Address Checking 5.1.4.4. Frame Type Validation 5.1.4.5. Payload Pad Removal 5.1.4.6. CRC Checking 5.1.4.7. Length Checking 5.1.4.8. Frame Writing 5.1.4.9. IP Payload Alignment
5.1.4.3. Address Checking x
5.1.4.3.1. Unicast Address Checking 5.1.4.3.2. Multicast Address Resolution
5.1.6. FIFO Buffer Thresholds x
5.1.6.1. Receive Thresholds 5.1.6.2. Transmit Thresholds 5.1.6.3. Transmit FIFO Buffer Underflow
5.1.7. Congestion and Flow Control x
5.1.7.1. Remote Device Congestion 5.1.7.2. Receive FIFO Buffer and Local Device Congestion
5.1.8. Magic Packets x
5.1.8.1. Sleep Mode 5.1.8.2. Magic Packet Detection
5.1.11. PHY Management (MDIO) x
5.1.11.1. MDIO Connection 5.1.11.2. MDIO Frame Format
5.1.12. Connecting MAC to External PHYs x
5.1.12.1. Gigabit Ethernet 5.1.12.2. Programmable 10/100 Ethernet 5.1.12.3. Programmable 10/100/1000 Ethernet Operation
5.2. 1000BASE-X/SGMII PCS With Optional Embedded PMA x
5.2.1. 1000BASE-X/SGMII PCS Architecture 5.2.2. Transmit Operation 5.2.3. Receive Operation 5.2.4. Transmit and Receive Latencies 5.2.5. GMII Converter 5.2.6. SGMII Converter 5.2.7. Auto-Negotiation 5.2.8. Ten-bit Interface 5.2.9. PHY Power-Down 5.2.10. 1000BASE-X/SGMII PCS Reset
5.2.2. Transmit Operation x
5.2.2.1. Frame Encapsulation 5.2.2.2. 8b/10b Encoding
5.2.3. Receive Operation x
5.2.3.1. Comma Detection 5.2.3.2. 8b/10b Decoding 5.2.3.3. Frame De-encapsulation 5.2.3.4. Synchronization 5.2.3.5. Carrier Sense 5.2.3.6. Collision Detection
5.2.6. SGMII Converter x
5.2.6.1. Transmit 5.2.6.2. Receive
5.2.7. Auto-Negotiation x
5.2.7.1. 1000BASE-X Auto-Negotiation 5.2.7.2. SGMII Auto-Negotiation
5.2.9. PHY Power-Down x
5.2.9.1. Power-Down in PCS Variations with Embedded PMA
6. Configuration Register Space x
6.1. MAC Configuration Register Space 6.2. PCS Configuration Register Space 6.3. Register Initialization
6.1. MAC Configuration Register Space x
6.1.1. Base Configuration Registers (Dword Offset 0x00 – 0x17) 6.1.2. Statistics Counters (Dword Offset 0x18 – 0x38) 6.1.3. Transmit and Receive Command Registers (Dword Offset 0x3A – 0x3B) 6.1.4. Supplementary Address (Dword Offset 0xC0 – 0xC7)
6.1.1. Base Configuration Registers (Dword Offset 0x00 – 0x17) x
6.1.1.1. Command_Config Register (Dword Offset 0x02)
6.2. PCS Configuration Register Space x
6.2.1. Control Register (Word Offset 0x00) 6.2.2. Status Register (Word Offset 0x01) 6.2.3. Dev_Ability and Partner_Ability Registers (Word Offset 0x04 – 0x05) 6.2.4. An_Expansion Register (Word Offset 0x06) 6.2.5. If_Mode Register (Word Offset 0x14)
6.2.3. Dev_Ability and Partner_Ability Registers (Word Offset 0x04 – 0x05) x
6.2.3.1. 1000BASE-X 6.2.3.2. SGMII MAC Mode Auto Negotiation 6.2.3.3. SGMII PHY Mode Auto Negotiation
6.3. Register Initialization x
6.3.1. F-tile Triple-Speed Ethernet System with MII/GMII 6.3.2. F-tile Triple-Speed Ethernet System with SGMII 6.3.3. F-tile Triple-Speed Ethernet System with 1000BASE-X Interface
7. Interface Signals x
7.1. Interface Signals 7.2. Timing
7.1. Interface Signals x
7.1.1. 10/100/1000 Ethernet MAC Signals 7.1.2. 10/100/1000 Multiport Ethernet MAC Signals 7.1.3. 10/100/1000 Ethernet MAC with 1000BASE-X/SGMII PCS Signals 7.1.4. 10/100/1000 Ethernet MAC with 1000BASE-X/SGMII 2XTBI PCS and Embedded PMA Signals (F-Tile) 7.1.5. 10/100/1000 Ethernet MAC Without Internal FIFO Buffers with 1000BASE-X/SGMII 2XTBI PCS Signals 7.1.6. 10/100/1000 Multiport Ethernet MAC with 1000BASE-X/SGMII PCS Signals 7.1.7. 10/100/1000 Ethernet MAC with 1000BASE-X/SGMII PCS and Embedded PMA Signals 7.1.8. 10/100/1000 Multiport Ethernet MAC with 1000BASE-X/SGMII PCS and Embedded PMA Signals 7.1.9. 1000BASE-X/SGMII PCS Signals 7.1.10. 1000BASE-X/SGMII 2XTBI PCS Signals 7.1.11. 1000BASE-X/SGMII PCS and PMA Signals
7.1.1. 10/100/1000 Ethernet MAC Signals x
7.1.1.1. Clock and Reset Signals 7.1.1.2. Clock Enabler Signals 7.1.1.3. MAC Control Interface Signals 7.1.1.4. MAC Status Signals 7.1.1.5. MAC Receive Interface Signals 7.1.1.6. MAC Transmit Interface Signals 7.1.1.7. Pause and Magic Packet Signals 7.1.1.8. MII/GMII/RGMII Signals 7.1.1.9. PHY Management Signals 7.1.1.10. ECC Status Signals
7.1.2. 10/100/1000 Multiport Ethernet MAC Signals x
7.1.2.1. Multiport MAC Clock and Reset Signals 7.1.2.2. Multiport MAC Receive Interface Signals 7.1.2.3. Multiport MAC Transmit Interface Signals 7.1.2.4. Multiport MAC Packet Classification Signals 7.1.2.5. Multiport MAC FIFO Status Signals
7.1.3. 10/100/1000 Ethernet MAC with 1000BASE-X/SGMII PCS Signals x
7.1.3.1. TBI Interface Signals 7.1.3.2. Status LED Control Signals 7.1.3.3. SERDES Control Signals 7.1.3.4. ECC Status Signals
7.1.4. 10/100/1000 Ethernet MAC with 1000BASE-X/SGMII 2XTBI PCS and Embedded PMA Signals (F-Tile) x
7.1.4.1. GMII Clock Signals 7.1.4.2. F-Tile Transceiver Direct PHY Signals
7.1.7. 10/100/1000 Ethernet MAC with 1000BASE-X/SGMII PCS and Embedded PMA Signals x
7.1.7.1. 1.25 Gbps Serial Interface 7.1.7.2. Transceiver Native PHY Signal 7.1.7.3. Intel LVDS Transmitter and Receiver Soft-CDR I/O Signals
7.1.9. 1000BASE-X/SGMII PCS Signals x
7.1.9.1. PCS Control Interface Signals 7.1.9.2. PCS Reset Signals 7.1.9.3. MII/GMII Clocks and Clock Enablers 7.1.9.4. GMII 7.1.9.5. MII 7.1.9.6. SGMII Status Signals
7.1.10. 1000BASE-X/SGMII 2XTBI PCS Signals x
7.1.10.1. Clock Enablers 7.1.10.2. PCS Reset Signals 7.1.10.3. TBI Interface Signals
7.2. Timing x
7.2.1. Avalon Streaming Receive Interface 7.2.2. Avalon Streaming Transmit Interface 7.2.3. GMII Transmit 7.2.4. GMII Receive 7.2.5. RGMII Transmit 7.2.6. RGMII Receive 7.2.7. MII Transmit 7.2.8. MII Receive
8. Design Considerations x
8.1. Optimizing Clock Resources in Multiport MAC with PCS and Embedded PMA 8.2. Sharing PLLs in Devices with LVDS Soft-CDR I/O 8.3. Exposed Ports in the New User Interface 8.4. Clocking Scheme of MAC with 2XTBI PCS and Embedded PMA
8.1. Optimizing Clock Resources in Multiport MAC with PCS and Embedded PMA x
8.1.1. MAC and PCS With LVDS Soft-CDR I/O
9. Timing Constraints x
9.1. Creating Clock Constraints 9.2. Recommended Clock Frequency
10. Software Programming Interface x
10.1. Driver Architecture 10.2. Directory Structure 10.3. PHY Definition 10.4. Using Multiple SG-DMA Descriptors 10.5. Using Jumbo Frames 10.6. API Functions 10.7. Constants
10.6. API Functions x
10.6.1. alt_tse_mac_get_common_speed() 10.6.2. alt_tse_mac_set_common_speed() 10.6.3. alt_tse_phy_add_profile() 10.6.4. alt_tse_system_add_sys() 10.6.5. triple_speed_ethernet_init() 10.6.6. tse_mac_close() 10.6.7. tse_mac_raw_send() 10.6.8. tse_mac_setGMII mode() 10.6.9. tse_mac_setMIImode() 10.6.10. tse_mac_SwReset()
A. Ethernet Frame Format x
A.1. Basic Frame Format A.2. VLAN and Stacked VLAN Frame Format A.3. Pause Frame Format
A.3. Pause Frame Format x
A.3.1. Pause Frame Generation
B. Simulation Parameters x
B.1. Functionality Configuration Parameters B.2. Test Configuration Parameters
1. About the F-Tile Triple Speed Ethernet Intel FPGA IP User Guide
2. About This IP
3. Getting Started
4. Parameter Settings
5. Functional Description
6. Configuration Register Space
7. Interface Signals
8. Design Considerations
9. Timing Constraints
10. Software Programming Interface
11. Document Revision History for the F-tile Triple-Speed Ethernet Intel® FPGA IP User Guide
A. Ethernet Frame Format
B. Simulation Parameters

6.1.1. Base Configuration Registers (Dword Offset 0x00 – 0x17)

The following table lists the base registers you can use to configure the MAC function. A software reset does not reset these registers except the first two bits (TX_ENA and RX_ENA = 0) in the command_config register.

Table 26.  Base Configuration Register Map
Dword

Offset

Name R/W Description HW Reset
0x00 rev RO
  • Bits[15:0]—Set to the current version of the IP.
  • Bits[31:16]—Customer specific revision, specified by the CUST_VERSION parameter defined in the top-level file generated for the instance of the IP. These bits are set to 0 during the configuration of the IP.
<IP version number>
0x01 scratch 10 RW Scratch register. Provides a memory location for you to test the device memory operation. 0
0x02 command_config RW MAC configuration register. Use this register to control and configure the MAC function. The MAC function starts operation as soon as the transmit and receive enable bits in this register are turned on. Intel, therefore, recommends that you configure this register last. 0
0x03 mac_0 RW 6-byte MAC primary address. The first four most significant bytes of the MAC address occupy mac_0 in reverse order. The last two bytes of the MAC address occupy the two least significant bytes of mac_1 in reverse order.

For example, if the MAC address is 00-1C-23-17-4A-CB, the following assignments are made:

mac_0 = 0x17231c00

mac_1 = 0x0000CB4a

Ensure that you configure these registers with a valid MAC address if you disable the promiscuous mode (PROMIS_EN bit in command_config = 0).

0
0x04 mac_1 RW 0
0x05 frm_length RW/

RO

  • Bits[15:0]—16-bit maximum frame length in bytes. The IP checks the length of receive frames against this value. Typical value is 1518.

    In the 10/100 Mbps and 1000 Mbps small MAC variations, this register is RO and the maximum frame length is fixed to 1518.

  • Bits[31:16]—unused.
1518
0x06 pause_quant RW
  • Bits[15:0]—16-bit pause quanta. Use this register to specify the pause quanta to be sent to remote devices when the local device is congested. The IP sets the pause quanta (P1, P2) field in pause frames to the value of this register.

    The 10/100 Mbps and 1000 Mbps small MAC variations do not support flow control.

  • Bits[31:16]—unused.
0
0x07 rx_section_empty RW/

RO

Variable-length section-empty threshold of the receive FIFO buffer. Use the depth of your FIFO buffer to determine this threshold. This threshold is typically set to (FIFO Depth – 16).

Set this threshold to a value that is below the rx_almost_full threshold and above the rx_section_full or rx_almost_empty threshold.

In the 10/100 Mbps and 1000 Mbps small MAC variations, this register is RO and the register is set to a fixed value of (FIFO Depth – 16).

0
0x08 rx_section_full RW/

RO

Variable-length section-full threshold of the receive FIFO buffer. Use the depth of your FIFO buffer to determine this threshold.

For cut-through mode, this threshold is typically set to 16. Set this threshold to a value that is above the rx_almost_empty threshold.

For store-and-forward mode, set this threshold to 0.

In the 10/100 Mbps and 1000 Mbps small MAC variations, this register is RO and the register is set to a fixed value of 16.

0
0x09 tx_section_empty RW/

RO

Variable-length section-empty threshold of the transmit FIFO buffer. Use the depth of your FIFO buffer to determine this threshold. This threshold is typically set to (FIFO Depth – 16).

Set this threshold to a value below the rx_almost_full threshold and above the rx_section_full or rx_almost_empty threshold.

In the 10/100 Mbps and 1000 Mbps small MAC variations, this register is RO and the register is set to a fixed value of (FIFO Depth – 16).

0
0x0A tx_section_full RW/

RO

Variable-length section-full threshold of the transmit FIFO buffer. Use the depth of your FIFO buffer to determine this threshold.

For cut-through mode, this threshold is typically set to 16. Set this threshold to a value above the tx_almost_empty threshold.

For store-and-forward mode, set this threshold to 0.

In the 10/100 Mbps and 1000 Mbps small MAC variations, this register is RO and the register is set to a fixed value of 16.

0
0x0B rx_almost_empty RW/

RO

Variable-length almost-empty threshold of the receive FIFO buffer. Use the depth of your FIFO buffer to determine this threshold.

Due to internal pipeline latency, you must set this threshold to a value greater than 3. This threshold is typically set to 8.

In the 10/100 Mbps and 1000 Mbps small MAC variations, this register is RO and the register is set to a fixed value of 8.

0
0x0C rx_almost_full RW/

RO

Variable-length almost-full threshold of the receive FIFO buffer. Use the depth of your FIFO buffer to determine this threshold.

Due to internal pipeline latency, you must set this threshold to a value greater than 3. This threshold is typically set to 8.

In the 10/100 Mbps and 1000 Mbps small MAC variations, this register is RO and the register is set to a fixed value of 8.

0
0x0D tx_almost_empty RW/

RO

Variable-length almost-empty threshold of the transmit FIFO buffer. Use the depth of your FIFO buffer to determine this threshold.

Due to internal pipeline latency, you must set this threshold to a value greater than 3. This threshold is typically set to 8.

In the 10/100 Mbps and 1000 Mbps small MAC variations, this register is RO and the register is set to a fixed value of 8.

0
0x0E tx_almost_full RW/

RO

Variable-length almost-full threshold of the transmit FIFO buffer. Use the depth of your FIFO buffer to determine this threshold.

You must set this register to a value greater than or equal to 3. A value of 3 indicates 0 ready latency; a value of 4 indicates 1 ready latency, and so forth. Because the maximum ready latency on the Avalon® streaming interface is 8, you can only set this register to a maximum value of 11. This threshold is typically set to 3.

In the 10/100 Mbps and 1000 Mbps small MAC variations, this register is RO and the register is set to a fixed value of 3.

0
0x0F mdio_addr0 RW
  • Bits[4:0]—5-bit PHY address. Set these registers to the addresses of any connected PHY devices you want to access. The mdio_addr0 and mdio_addr1 registers contain the addresses of the PHY whose registers are mapped to MDIO Space 0 and MDIO Space 1 respectively.
  • Bits[31:5]—unused. Set to read-only value of 0.
0
0x10 mdio_addr1 RW 1
0x11 holdoff_quant RW
  • Bit[15:0]—16-bit holdoff quanta. When you enable the flow control, use this register to specify the gap between consecutive XOFF requests.
  • Bits[31:16]—unused.
0xFFFF
0x12 – 0x16 Reserved — — 0
0x17 tx_ipg_length RW
  • Bits[4:0]—minimum IPG. Valid values are between 8 and 26 byte-times. If this register is set to an invalid value, the MAC still maintains a typical minimum IPG value of 12 bytes between packets, although a read back to the register reflects the invalid value written.

    In the 10/100 Mbps and 1000 Mbps small MAC variations, this register is RO and the register is set to a fixed value of 12.

    Bits[31:5]—unused. Set to read-only value 0.

0

Section Content
Command_Config Register (Dword Offset 0x02)

10 Register is not available in 10/100 Mbps and 1000 Mbps small MAC variations.
Level Two Title