MACsec Intel® FPGA IP User Guide

Download PDF
ID 736108
Date 12/04/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Introduction 2. Interface Overview 3. Parameters 4. Designing with the IP Core 5. Functional Description 6. Configuration Registers for MACsec IP 7. MACsec Intel® FPGA IP Example Design 8. MACsec Intel FPGA IP User Guide Archives 9. Document Revision History for the MACsec Intel FPGA IP User Guide
1. Introduction x
1.1. Terminology 1.2. IP Core Overview 1.3. Release Information 1.4. Device Family Support 1.5. Device Speed Grade Support and Theoretical Throughput 1.6. Resource Utilization
1.2. IP Core Overview x
1.2.1. IP Description 1.2.2. IP Core Applications
1.2.2. IP Core Applications x
1.2.2.1. SmartNIC 1.2.2.2. Ethernet Bridge + Inline MACsec
2. Interface Overview x
2.1. Block Diagram 2.2. Interfaces 2.3. Clocking Domains
2.2. Interfaces x
2.2.1. IP Interface Signals 2.2.2. IP Interface Signal Timing Diagram/Waveforms 2.2.3. Clocks, Resets, and Interrupts
2.2.1. IP Interface Signals x
2.2.1.1. Common Port Mux Interface 2.2.1.2. Common Port Demux Interface 2.2.1.3. Controlled Port Mux Interface 2.2.1.4. Controlled Port Demux Interface 2.2.1.5. Uncontrolled Port RX Interface 2.2.1.6. Uncontrolled Port TX Interface 2.2.1.7. Management Interface 2.2.1.8. Decrypt Port Mux Management Interface 2.2.1.9. Decrypt Port Demux Management Interface 2.2.1.10. Encrypt Port Mux Management Interface 2.2.1.11. Encrypt Port Demux Management Interface 2.2.1.12. Crypto IP Management Bus 2.2.1.13. Miscellaneous Control Signals
2.2.2. IP Interface Signal Timing Diagram/Waveforms x
2.2.2.1. Common Port Mux Interface Waveform 2.2.2.2. Common Port Demux Interface Waveform 2.2.2.3. Controlled Port Mux Interface Waveform 2.2.2.4. Controlled Port Demux Interface Waveform 2.2.2.5. Uncontrolled Port RX Interface Waveform 2.2.2.6. Uncontrolled Port TX Interface Waveform 2.2.2.7. Crypto RX Waveform 2.2.2.8. Crypto TX Waveform 2.2.2.9. MACsec Management Interface (Read) 2.2.2.10. MACsec Management Interface (Write)
3. Parameters x
3.1. MACsec Intel FPGA IP Parameter Settings
4. Designing with the IP Core x
4.1. Installing and Licensing Intel® FPGA IP Cores 4.2. Specifying the IP Core Parameters and Options 4.3. Generated File Structure 4.4. Reset Transactions 4.5. MACsec Software Initialization Sequence
4.1. Installing and Licensing Intel® FPGA IP Cores x
4.1.1. Intel® FPGA IP Evaluation Mode
5. Functional Description x
5.1. AXI-ST Common/Controlled/Uncontrolled Ports 5.2. Packet Parser and Classifier 5.3. SA Lookup and Update 5.4. Encryption Framer/DeFramer 5.5. Decryption Framer/Deframer 5.6. Packet Aggregator/Disaggregator 5.7. Cryptographic AES 5.8. Error Handling 5.9. Packet Statistics
5.1. AXI-ST Common/Controlled/Uncontrolled Ports x
5.1.1. AXI-ST Single Packet Mode 5.1.2. AXI-ST Multi Packet Mode 5.1.3. User Interface Data Streaming 5.1.4. AXI-ST Ready Latency 5.1.5. Port and Secure Channel Mapping 5.1.6. Port and Crypto Channel Mapping 5.1.7. Minimum Packet Size 5.1.8. Byte Ordering 5.1.9. Controlled/Uncontrolled Port Muxing
5.1.3. User Interface Data Streaming x
5.1.3.1. Single Packet Mode Data Stream 5.1.3.2. Multi Packet Mode Data Stream
5.2. Packet Parser and Classifier x
5.2.1. Packet Parser 5.2.2. Packet Classifier
5.3. SA Lookup and Update x
5.3.1. Packet Actions 5.3.2. Packet Buffer 5.3.3. New Channel Assignment 5.3.4. Anti-Replay Protection
5.3.1. Packet Actions x
5.3.1.1. Packet Encrypt 5.3.1.2. Packet Decrypt 5.3.1.3. Packet Discard 5.3.1.4. PDU Validation
5.4. Encryption Framer/DeFramer x
5.4.1. Channel Allocation 5.4.2. Packet Framer 5.4.3. VLAN Tagging
5.4.2. Packet Framer x
5.4.2.1. Bypass Packet 5.4.2.2. Stream Interleaving
5.4.3. VLAN Tagging x
5.4.3.1. No VLAN Tag 5.4.3.2. VLAN Tag (Not in Clear) 5.4.3.3. VLAN Tag (Clear)
5.5. Decryption Framer/Deframer x
5.5.1. XPN Recovery 5.5.2. Replay Check Update 5.5.3. Packet Deframer
5.6. Packet Aggregator/Disaggregator x
5.6.1. Packet Aggregator 5.6.2. Packet Disaggregator
5.7. Cryptographic AES x
5.7.1. Register Address Ordering 5.7.2. Byte Order Swapping 5.7.3. Byte Ordering
5.8. Error Handling x
5.8.1. Packet Error Handling 5.8.2. Memory Blocks ECC Errors 5.8.3. Crypto Errors 5.8.4. System-Level Errors
7. MACsec Intel® FPGA IP Example Design x
7.1. Simulation Requirements 7.2. Steps to Run Simulation 7.3. Port Configurations 7.4. Multi Interface Buffering Muxing/Demuxing 7.5. 2x25 GbE (Encryption + Decryption) 7.6. Packet Generator/Checker 7.7. Clocking
1. Introduction
2. Interface Overview
3. Parameters
4. Designing with the IP Core
5. Functional Description
6. Configuration Registers for MACsec IP
7. MACsec Intel® FPGA IP Example Design
8. MACsec Intel FPGA IP User Guide Archives
9. Document Revision History for the MACsec Intel FPGA IP User Guide

9. Document Revision History for the MACsec Intel FPGA IP User Guide

Document Version Intel® Quartus® Prime Version IP Version Changes
2023.12.04 23.4 2.2.0
  • Updated the IP Core Release Information table.
  • Updated the Resource Utilization table.
  • Updated the Reset Transaction section.
2023.10.02 23.3 2.1.0
  • Updated the Resource Utilization.
  • Removed the Crypto RX Interface and Crypto TX Interface tables.
  • Updated all interface tables.
  • Updated the MACsec IP Parameter Settings table.
  • Updated the Available MACsec Design Example Variant table.
  • Miscellaneous text changes throughout the manual.
2023.06.26 23.2 2.0.0
  • Updated the Resource Utilization table.
  • Updated the MACsec IP Block Diagram.
  • Updated the MACsec IP Parameters Settings table.
  • Updated the MACsec IP Reset Tree diagram.
  • Updated the MACsec IP Design Example diagram.
  • Updated the Controlled/Uncontrolled Port Muxing descriptions.
2023.04.03 23.1 1.4.0
  • Added the Simulation Requirements section in the chapter MACsec IP Example Design.
  • In the MACsec IP Parameter Settings table, added the Snapshot Enable parameter.
  • Updated the register map with the snapshot control register information.
  • Updated the Port Configurations section in the chapter MACsec IP Example Design.
  • Updated the MACsec IP Parameters Settings table.
  • Updated product family name to Intel Agilex 7.
2022.12.19 22.4 1.3.0
  • Added more description in the section SmartNIC.
  • Updated the Resource Utilization table.
  • Consolidated the "last_segment*" signals in all the interface tables and waveforms in the Interfaces chapter.
  • Updated the figure MACsec Intel FPGA IP Clock Domain
  • Updated the table MACsec Intel FPGA IP Parameter Settings.
  • Updated the table Available MACsec Design Example Variant.
  • Updated the table Clocking Parameters.
  • Removed the section MACsec Software Rekeying.
  • Added a new section Switching Port Muxes between Store and Forward and Cut-Through Modes
  • Updated the Register Map by removing 3 registers.
  • Made other miscellaneous changes throughout the manual.
2022.10.21 22.3 1.2.0 Initial release.
Level Two Title