MACsec Intel® FPGA IP User Guide

Download PDF
ID 736108
Date 12/19/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Introduction 2. Interface Overview 3. Parameters 4. Designing with the IP Core 5. MACsec Intel® FPGA IP Example Design 6. Functional Description 7. Configuration Registers for MACsec IP 8. MACsec Intel FPGA IP User Guide Archives 9. Document Revision History for the MACsec Intel FPGA IP User Guide
1. Introduction x
1.1. Terminology 1.2. IP Core Overview 1.3. Release Information 1.4. Device Family Support 1.5. Device Speed Grade Support and Theoretical Throughput 1.6. Resource Utilization
1.2. IP Core Overview x
1.2.1. IP Description 1.2.2. IP Core Applications
1.2.2. IP Core Applications x
1.2.2.1. SmartNIC 1.2.2.2. Ethernet Bridge + Inline MACsec
2. Interface Overview x
2.1. Block Diagram 2.2. Interfaces 2.3. Clocking Domains
2.2. Interfaces x
2.2.1. IP Interface Signals 2.2.2. IP Interface Signal Timing Diagram/Waveforms 2.2.3. Clocks, Resets, and Interrupts
2.2.1. IP Interface Signals x
2.2.1.1. Common Port Mux Interface 2.2.1.2. Common Port Demux Interface 2.2.1.3. Controlled Port Mux Interface 2.2.1.4. Controlled Port Demux Interface 2.2.1.5. Uncontrolled Port RX Interface 2.2.1.6. Uncontrolled Port TX Interface 2.2.1.7. Crypto RX Interface 2.2.1.8. Crypto TX Interface 2.2.1.9. Management Interface 2.2.1.10. Decrypt Port Mux Management Interface 2.2.1.11. Decrypt Port Demux Management Interface 2.2.1.12. Encrypt Port Mux Management Interface 2.2.1.13. Encrypt Port Demux Management Interface 2.2.1.14. Crypto IP Management Bus
2.2.2. IP Interface Signal Timing Diagram/Waveforms x
2.2.2.1. Common Port Mux Interface Waveform 2.2.2.2. Common Port Demux Interface Waveform 2.2.2.3. Controlled Port Mux Interface Waveform 2.2.2.4. Controlled Port Demux Interface Waveform 2.2.2.5. Uncontrolled Port RX Interface Waveform 2.2.2.6. Uncontrolled Port TX Interface Waveform 2.2.2.7. Crypto RX Waveform 2.2.2.8. Crypto TX Waveform 2.2.2.9. MACsec Management Interface (Read) 2.2.2.10. MACsec Management Interface (Write)
3. Parameters x
3.1. MACsec Intel FPGA IP Parameter Settings
4. Designing with the IP Core x
4.1. Installing and Licensing Intel® FPGA IP Cores 4.2. Specifying the IP Core Parameters and Options 4.3. Generated File Structure 4.4. Reset Transactions 4.5. MACsec Software Initialization Sequence 4.6. Switching Port Muxes between Store and Forward and Cut-Through Modes
4.1. Installing and Licensing Intel® FPGA IP Cores x
4.1.1. Intel® FPGA IP Evaluation Mode
5. MACsec Intel® FPGA IP Example Design x
5.1. Port Configurations 5.2. Multi Interface Buffering Muxing/Demuxing 5.3. 2x25 GbE (Encryption + Decryption) 5.4. Packet Generator/Checker 5.5. Clocking
6. Functional Description x
6.1. AXI-ST Common/Controlled/Uncontrolled Ports 6.2. Packet Parser and Classifier 6.3. SA Lookup and Update 6.4. Encryption Framer/DeFramer 6.5. Decryption Framer/Deframer 6.6. Packet Aggregator/Disaggregator 6.7. Cryptographic AES 6.8. Error Handling 6.9. Packet Statistics
6.1. AXI-ST Common/Controlled/Uncontrolled Ports x
6.1.1. AXI-ST Single Packet Mode 6.1.2. AXI-ST Multi Packet Mode 6.1.3. User Interface Data Streaming 6.1.4. AXI-ST Ready Latency 6.1.5. Port and Secure Channel Mapping 6.1.6. Port and Crypto Channel Mapping 6.1.7. Minimum Packet Size 6.1.8. Byte Ordering 6.1.9. Controlled/Uncontrolled Port Muxing
6.1.3. User Interface Data Streaming x
6.1.3.1. Single Packet Mode Data Stream 6.1.3.2. Multi Packet Mode Data Stream
6.2. Packet Parser and Classifier x
6.2.1. Packet Parser 6.2.2. Packet Classifier
6.3. SA Lookup and Update x
6.3.1. Packet Actions 6.3.2. Packet Buffer 6.3.3. New Channel Assignment 6.3.4. Anti-Replay Protection
6.3.1. Packet Actions x
6.3.1.1. Packet Encrypt 6.3.1.2. Packet Decrypt 6.3.1.3. Packet Discard 6.3.1.4. PDU Validation
6.4. Encryption Framer/DeFramer x
6.4.1. Channel Allocation 6.4.2. Packet Framer 6.4.3. VLAN Tagging
6.4.2. Packet Framer x
6.4.2.1. Bypass Packet 6.4.2.2. Stream Interleaving
6.4.3. VLAN Tagging x
6.4.3.1. No VLAN Tag 6.4.3.2. VLAN Tag (Not in Clear) 6.4.3.3. VLAN Tag (Clear)
6.5. Decryption Framer/Deframer x
6.5.1. XPN Recovery 6.5.2. Replay Check Update 6.5.3. Packet Deframer
6.6. Packet Aggregator/Disaggregator x
6.6.1. Packet Aggregator 6.6.2. Packet Disaggregator
6.7. Cryptographic AES x
6.7.1. Register Address Ordering 6.7.2. Byte Order Swapping 6.7.3. Byte Ordering
6.8. Error Handling x
6.8.1. Packet Error Handling 6.8.2. Memory Blocks ECC Errors 6.8.3. Crypto Errors 6.8.4. System-Level Errors
1. Introduction
2. Interface Overview
3. Parameters
4. Designing with the IP Core
5. MACsec Intel® FPGA IP Example Design
6. Functional Description
7. Configuration Registers for MACsec IP
8. MACsec Intel FPGA IP User Guide Archives
9. Document Revision History for the MACsec Intel FPGA IP User Guide

4.2. Specifying the IP Core Parameters and Options

The IP parameter editor allows you to quickly configure your custom IP variation. Use the following steps to specify IP core options and parameters in the Intel® Quartus® Prime Pro Edition software.

  1. If you do not already have an Intel® Quartus® Prime Pro Edition project in which to integrate your Symmetric Cryptographic Intel® FPGA Hard IP core, you must create one.
    1. In the Intel® Quartus® Prime Pro Edition, click File > New Project Wizard to create a new Quartus Prime project, or File > Open Project to open an existing Quartus Prime project. The wizard prompts you to specify a device.
    2. Specify the device family Intel® Agilex™ and select a device that contains the Symmetric Cryptographic Intel® FPGA Hard IP that meets the speed grade requirements for the IP core.
    3. Click Finish.
  2. In the IP Catalog, locate and select MACsec Intel® FPGA IP. The New IP Variation window appears.
  3. Specify a top-level name for your new custom IP variation. The parameter editor saves the IP variation settings in a file named <your_ip> .ip.
  4. Click OK. The parameter editor appears.
  5. Specify the parameters for your IP core variation. Refer to MACsec Intel FPGA IP Parameter Settings for information about specific IP core parameters.
  6. Optionally, to generate a simulation testbench or compilation and hardware design example, follow the instructions in the MACsec Intel FPGA IP Example Design.
  7. Click Generate HDL. The Generation dialog box appears.
  8. Specify output file generation options, and then click Generate. The IP variation files generate according to your specifications.
  9. Click Finish. The parameter editor adds the top-level .ip file to the current project automatically. If you are prompted to manually add the .ip file to the project, click Project > Add/Remove Files in Project to add the file.
Level Two Title