Stratix® 10 SoC FPGA Boot User Guide

Download PDF
ID 683847
Date 8/23/2024
Public
Document Table of Contents
Document Table of Contents x
1. Introduction 2. FPGA Configuration First Mode 3. HPS Boot First Mode 4. Creating the Configuration Files 5. Golden System Reference Design and Design Examples 6. Configuring the FPGA Fabric from HPS Software 7. Debugging the Stratix® 10 SoC FPGA Boot Flow 8. Stratix® 10 SoC FPGA Boot User Guide Archives 9. Document Revision History for Stratix® 10 SoC FPGA Boot User Guide
1. Introduction x
1.1. Glossary 1.2. Stratix® 10 SoC FPGA Boot Overview
2. FPGA Configuration First Mode x
2.1. Boot Flow Overview for FPGA Configuration First Mode 2.2. System Layout for FPGA Configuration First Mode
2.1. Boot Flow Overview for FPGA Configuration First Mode x
2.1.1. Power-On Reset (POR) 2.1.2. Secure Device Manager 2.1.3. First-Stage Bootloader 2.1.4. Second-Stage Bootloader 2.1.5. Operating System 2.1.63.1.6. Application2.1.63.1.6. Application
2.2. System Layout for FPGA Configuration First Mode x
2.2.1. External Configuration Host Only 2.2.2. External Configuration Host with HPS Flash 2.2.3. Single SDM Flash 2.2.4. FPGA Configuration - First Dual Flash System
3. HPS Boot First Mode x
3.1. Boot Flow Overview 3.2. System Layout for HPS Boot First Mode
3.1. Boot Flow Overview x
3.1.1. Power-On Reset (POR) 3.1.2. Secure Device Manager 3.1.3. First-Stage Bootloader 3.1.4. Second-Stage Bootloader 3.1.5. Operating System 2.1.63.1.6. Application2.1.63.1.6. Application
3.2. System Layout for HPS Boot First Mode x
3.2.1. External Configuration Host Only 3.2.2. External Configuration Host with HPS Flash 3.2.3. Single SDM Flash 3.2.4. HPS Boot First - Dual Flash System
4. Creating the Configuration Files x
4.1. Overview 4.2. Quartus® Prime Hardware Project Compilation 4.3. Bootloader Software Compilation 4.4. Programming File Generator 4.5. Configuration over JTAG 4.6. Configuration from QSPI 4.7. Configuration over AVST 4.8. Configuration via Protocol 4.9. Remote System Update 4.10. Partial Reconfiguration
4.2. Quartus® Prime Hardware Project Compilation x
4.2.1. Device and Pin Options 4.2.2. Platform Designer Options
4.5. Configuration over JTAG x
4.5.1. FPGA Configuration First 4.5.2. HPS Boots First
4.6. Configuration from QSPI x
4.6.1. Supported QSPI Devices 4.6.2. FPGA Configuration First 4.6.3. HPS Boot First
4.6.2. FPGA Configuration First x
4.6.2.1. Creating Configuration Files from Command Line 4.6.2.2. Creating Configuration Files Using Graphical Interface
4.6.3. HPS Boot First x
4.6.3.1. Creating Configuration Files from Command Line 4.6.3.2. Creating Configuration Files Using Graphical Interface
4.7. Configuration over AVST x
4.7.1. FPGA Configuration First 4.7.2. HPS Boot First
4.7.1. FPGA Configuration First x
4.7.1.1. Creating Configuration Files from Command Line 4.7.1.2. Creating Configuration Files Using Graphical Interface
4.7.2. HPS Boot First x
4.7.2.1. Creating Configuration Files from Command Line 4.7.2.2. Creating Configuration Files Using Graphical Interface
4.8. Configuration via Protocol x
4.8.1. Creating Configuration Files from Command Line 4.8.2. Creating Configuration Files Using Graphical Interface
5. Golden System Reference Design and Design Examples x
5.1. Golden System Reference Design 5.2. Bootloader Examples 5.3. Additional Design Examples
6. Configuring the FPGA Fabric from HPS Software x
6.1. Configuring the FPGA Fabric from U-Boot 6.2. Configuring the FPGA Fabric from Linux 6.3. FPGA Partial Reconfiguration from Linux
7. Debugging the Stratix® 10 SoC FPGA Boot Flow x
7.1. Reset 7.2. Debugging the HPS Bootloader Using the Arm* DS* Intel® SoC FPGA Edition 7.3. Other Debug Considerations
7.1. Reset x
7.1.1. HPS Reset Pin 7.1.2. L4 Watchdog Timer 0
1. Introduction
2. FPGA Configuration First Mode
3. HPS Boot First Mode
4. Creating the Configuration Files
5. Golden System Reference Design and Design Examples
6. Configuring the FPGA Fabric from HPS Software
7. Debugging the Stratix® 10 SoC FPGA Boot Flow
8. Stratix® 10 SoC FPGA Boot User Guide Archives
9. Document Revision History for Stratix® 10 SoC FPGA Boot User Guide

4.6.3. HPS Boot First

In this case, the device reads a small phase 1 bitstream from QSPI flash and uses it to configure the HPS IO, HPS DDR, and bring up the HPS software. Then later the HPS software can configure the FPGA fabric using the typically much larger phase 2 configuration bitstream. The following figure shows an overview of the process:
Figure 18. Configuration from QSPI using HPS Boot First

The following steps are involved:

  1. Compile hardware project with Quartus® Prime to obtain the SOF file.
  2. Compile the HPS FSBL source code to obtain the HPS FSBL hex file, or use a precompiled one.
  3. Use Programming File Generator to create the following files:
    • HPS JTAG Indirect Configuration (JIC) file: contains the small phase 1 configuration bitstream and a small SDM helper firmware image used by the Quartus® Prime Programmer to write the bitstream to flash.
    • [Optional] HPS Raw Programming Data (RPD) File: contains the small phase 1 configuration bitstream in simple binary format. Can be written to flash with a 3rd party programmer, such as U-Boot.
    • Core RBF file: contains the phase 2 configuration bitstream, to be used by HPS software to configure the FPGA fabric.
    • [Optional] Map file: describes the flash placement and usage in human-readable text format.
  4. Use the Quartus® Prime Programmer to write the JIC image to QSPI flash. Alternatively use a 3rd party programmer to write the RPD image to flash.
  5. Set MSEL to QSPI, then power up, power cycle or toggle nCONFIG to cause the device to configure itself from QSPI.
  6. HPS software starts running, beginning with HPS FSBL.
  7. Later HPS software configures the FPGA fabric by using the phase 2 Core RBF bitstream.
Note: The phase 1 and phase 2 configuration bitstreams must be created by the exact same Quartus® Prime Programming File Generator version, including the same firmware patches. Also, the phase 1 and phase 2 configuration bitstreams must have the same HPS IO settings, including the HPS DDR settings. If these conditions are not both met, the phase 2 configuration fails.

Section Content
Creating Configuration Files from Command Line
Creating Configuration Files Using Graphical Interface

Level Two Title