Intel® Stratix® 10 High-Speed LVDS I/O User Guide

Download PDF
ID 683792
Date 7/13/2021
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Intel® Stratix® 10 High-Speed LVDS I/O Overview 2. Intel® Stratix® 10 High-Speed LVDS I/O Architecture and Features 3. Stratix 10 High-Speed LVDS I/O Design Considerations 4. Intel® Stratix® 10 High-Speed LVDS I/O Implementation Guides 5. LVDS SERDES Intel® FPGA IP References 6. Intel® Stratix® 10 High-Speed LVDS I/O User Guide Archives 7. Document Revision History for the Intel® Stratix® 10 High-Speed LVDS I/O User Guide
1. Intel® Stratix® 10 High-Speed LVDS I/O Overview x
1.1. Intel® Stratix® 10 LVDS SERDES Usage Modes 1.2. Intel® Stratix® 10 LVDS Channels Support 1.3. Intel® Stratix® 10 GPIO Banks, SERDES, and DPA Locations
2. Intel® Stratix® 10 High-Speed LVDS I/O Architecture and Features x
2.1. Intel® Stratix® 10 LVDS SERDES I/O Standards Support 2.2. LVDS Transmitter Programmable I/O Features 2.3. SERDES Circuitry 2.4. Differential Transmitter in Intel® Stratix® 10 Devices 2.5. Differential Receiver in Intel® Stratix® 10 Devices
2.2. LVDS Transmitter Programmable I/O Features x
2.2.1. Programmable Pre-Emphasis 2.2.2. Programmable Differential Output Voltage
2.4. Differential Transmitter in Intel® Stratix® 10 Devices x
2.4.1. Transmitter Blocks in Intel® Stratix® 10 Devices 2.4.2. Serializer Bypass for DDR and SDR Operations
2.5. Differential Receiver in Intel® Stratix® 10 Devices x
2.5.1. Receiver Blocks in Intel® Stratix® 10 Devices 2.5.2. Receiver Modes in Intel® Stratix® 10 Devices
2.5.1. Receiver Blocks in Intel® Stratix® 10 Devices x
2.5.1.1. DPA Block 2.5.1.2. Synchronizer 2.5.1.3. Data Realignment Block (Bit Slip) 2.5.1.4. Deserializer
2.5.2. Receiver Modes in Intel® Stratix® 10 Devices x
2.5.2.1. Non-DPA Mode 2.5.2.2. DPA Mode 2.5.2.3. Soft-CDR Mode
3. Stratix 10 High-Speed LVDS I/O Design Considerations x
3.1. PLLs and Clocking for Intel® Stratix® 10 Devices 3.2. Source-Synchronous Timing Budget 3.3. Guideline: LVDS SERDES IP Core Instantiation 3.4. Guideline: LVDS SERDES Pin Pairs for Soft-CDR Mode 3.5. Guideline: LVDS Transmitters and Receivers in the Same I/O Bank 3.6. Guideline: LVDS SERDES Limitation for Intel® Stratix® 10 GX 400, SX 400, and TX 400
3.1. PLLs and Clocking for Intel® Stratix® 10 Devices x
3.1.1. Clocking Differential Transmitters 3.1.2. Clocking Differential Receivers 3.1.3. Guideline: LVDS Reference Clock Source 3.1.4. Guideline: Use PLLs in Integer PLL Mode for LVDS 3.1.5. Guideline: Use High-Speed Clock from PLL to Clock LVDS SERDES Only 3.1.6. Guideline: Pin Placement for Differential Channels 3.1.7. LVDS Interface with External PLL Mode
3.1.6. Guideline: Pin Placement for Differential Channels x
3.1.6.1. PLLs Driving Differential Transmitter Channels 3.1.6.2. PLLs Driving DPA-Enabled Differential Receiver Channels 3.1.6.3. PLLs Driving DPA-Enabled Differential Receiver and Transmitter Channels in LVDS Interface Spanning Multiple I/O Banks
3.1.7. LVDS Interface with External PLL Mode x
3.1.7.1. IOPLL IP Core Signal Interface with LVDS SERDES IP Core 3.1.7.2. IOPLL Parameter Values for External PLL Mode 3.1.7.3. Connection between IOPLL IP Core and LVDS SERDES IP Core in External PLL Mode
3.2. Source-Synchronous Timing Budget x
3.2.1. Differential Data Orientation 3.2.2. Differential I/O Bit Position 3.2.3. Transmitter Channel-to-Channel Skew 3.2.4. Receiver Skew Margin for Non-DPA Mode
3.2.2. Differential I/O Bit Position x
3.2.2.1. Differential Bit Naming Conventions
3.2.4. Receiver Skew Margin for Non-DPA Mode x
3.2.4.1. RSKM Equation 3.2.4.2. Example: RSKM Calculation
3.5. Guideline: LVDS Transmitters and Receivers in the Same I/O Bank x
3.5.1. Using the Duplex Feature 3.5.2. Using an External PLL
4. Intel® Stratix® 10 High-Speed LVDS I/O Implementation Guides x
4.1. LVDS SERDES Intel® FPGA IP 4.2. LVDS SERDES IP Core Initialization and Reset 4.3. LVDS SERDES IP Core Timing 4.4. LVDS SERDES IP Core Design Examples 4.5. IP Migration Flow for Arria® V, Cyclone® V, and Stratix® V Devices
4.1. LVDS SERDES Intel® FPGA IP x
4.1.1. Release Information 4.1.2. LVDS SERDES IP Core Features 4.1.3. LVDS SERDES IP Core Functional Modes 4.1.4. LVDS SERDES IP Core Functional Description
4.1.4. LVDS SERDES IP Core Functional Description x
4.1.4.1. Serializer 4.1.4.2. DPA FIFO 4.1.4.3. Bitslip 4.1.4.4. Deserializer 4.1.4.5. Clock Phase Alignment
4.2. LVDS SERDES IP Core Initialization and Reset x
4.2.1. Initializing the LVDS SERDES IP Core in Non-DPA Mode 4.2.2. Initializing the LVDS SERDES IP Core in DPA Mode 4.2.3. Resetting the DPA 4.2.4. Word Boundaries Alignment
4.2.4. Word Boundaries Alignment x
4.2.4.1. Aligning Word Boundaries
4.3. LVDS SERDES IP Core Timing x
4.3.1. I/O Timing Analysis 4.3.2. FPGA Timing Analysis 4.3.3. Timing Analysis for the External PLL Mode 4.3.4. Timing Closure Guidelines for Internal FPGA Paths 4.3.5. Guideline: Use Clock Phase Alignment Block to Improve Timing Closure
4.3.1. I/O Timing Analysis x
4.3.1.1. Obtaining RSKM Report 4.3.1.2. Obtaining TCCS Report
4.4. LVDS SERDES IP Core Design Examples x
4.4.1. LVDS SERDES IP Core Synthesizable Intel® Quartus® Prime Design Examples 4.4.2. LVDS SERDES IP Core Simulation Design Example 4.4.3. Combined LVDS SERDES IP Core Transmitter and Receiver Design Example 4.4.4. LVDS SERDES IP Core Dynamic Phase Shift Design Example
4.5. IP Migration Flow for Arria® V, Cyclone® V, and Stratix® V Devices x
4.5.1. Migrating Your ALTLVDS_TX and ALTLVDS_RX IP Cores
5. LVDS SERDES Intel® FPGA IP References x
5.1. LVDS SERDES IP Core Parameter Settings 5.2. LVDS SERDES IP Core Signals 5.3. Comparison of LVDS SERDES Intel® FPGA IP with Stratix® V SERDES
5.1. LVDS SERDES IP Core Parameter Settings x
5.1.1. LVDS SERDES IP Core General Settings 5.1.2. LVDS SERDES IP Core PLL Settings 5.1.3. LVDS SERDES IP Core Receiver Settings 5.1.4. LVDS SERDES IP Core Transmitter Settings 5.1.5. LVDS SERDES IP Core Clock Resource Summary
5.1.3. LVDS SERDES IP Core Receiver Settings x
5.1.3.1. Receiver Input Clock Parameters Setup
5.1.4. LVDS SERDES IP Core Transmitter Settings x
5.1.4.1. Setting the Transmitter Output Clock Parameters
1. Intel® Stratix® 10 High-Speed LVDS I/O Overview
2. Intel® Stratix® 10 High-Speed LVDS I/O Architecture and Features
3. Stratix 10 High-Speed LVDS I/O Design Considerations
4. Intel® Stratix® 10 High-Speed LVDS I/O Implementation Guides
5. LVDS SERDES Intel® FPGA IP References
6. Intel® Stratix® 10 High-Speed LVDS I/O User Guide Archives
7. Document Revision History for the Intel® Stratix® 10 High-Speed LVDS I/O User Guide

3.1.7.1. IOPLL IP Core Signal Interface with LVDS SERDES IP Core

Table 10.  Signal Interface between IOPLL and LVDS SERDES IP cores This table lists the signal interface between the output ports of the IOPLL IP core and the input ports of the LVDS SERDES IP core transmitter or receiver. The required signal interfaces differ if you turn on the Clock Phase Alignment (CPA) feature of the LVDS SERDES IP core.
From the IOPLL IP core To the LVDS SERDES IP core transmitter or receiver
Without CPA With CPA
lvds_clk[0] (serial clock output signal)
  • Configure this signal using outclk0 in the PLL.
  • Select Enable LVDS_CLK/LOADEN 0 or Enable LVDS_CLK/LOADEN 0 & 1 option for the Access to PLL LVDS_CLK/LOADEN output port setting. In most cases, select Enable LVDS_CLK/LOADEN 0.

The serial clock output can only drive ext_fclk on the LVDS SERDES IP core transmitter and receiver. This clock cannot drive the core logic.

ext_fclk (serial clock input to the transmitter or receiver)

ext_fclk (serial clock input to the transmitter or receiver)

loaden[0] (load enable output)

  • Configure this signal using outclk1 in the PLL.
  • Select Enable LVDS_CLK/LOADEN 0 or Enable LVDS_CLK/LOADEN 0 & 1 option for the Access to PLL LVDS_CLK/LOADEN output port setting. In most cases, select Enable LVDS_CLK/LOADEN 0.

ext_loaden (load enable to the transmitter or receiver)

This signal is not required for LVDS receiver in soft-CDR mode.

ext_loaden (load enable to the transmitter or receiver)

This signal is not required for LVDS receiver in soft-CDR mode.

outclk4 (parallel clock output)

This clock is not required if you turn on Use the CPA block for improved periphery-core timing.

ext_coreclock (parallel core clock)

—

locked

—

ext_pll_locked

reset

pll_areset (asynchronous PLL reset port)

pll_areset (asynchronous PLL reset port)

phout[7:0]

  • This signal is required if ext_vcoph[7:0] is required.

  • Configure this signal by turning on Specify VCO frequency in the PLL and specifying the VCO frequency value.
  • Turn on Enable access to PLL DPA output port.

ext_vcoph[7:0]

This signal is required only for LVDS receiver in DPA or soft-CDR mode.

ext_vcoph[7:0]

This signal is required for all transmitter or receiver modes.

Related Information
Level Two Title