Intel® Cyclone® 10 GX Device Design Guidelines

Download PDF
ID 683703
Date 11/06/2017
Public
Document Table of Contents
Document Table of Contents x
Intel® Cyclone® 10 GX Device Design Guidelines
Intel® Cyclone® 10 GX Device Design Guidelines x
System Specification Device Selection Early System and Board Planning Pin Connection Considerations for Board Design I/O and Clock Planning Design Entry Design Implementation, Analysis, Optimization, and Verification Design Checklist Appendix: Cyclone® 10 GX Transceiver Design Guidelines Conclusion Document Revision History
System Specification x
Design Specifications IP Selection Platform Designer
Device Selection x
Logic, Memory, and Multiplier Density I/O Pin Count, LVDS Channels, and Package Offering PLLs and Clock Routing Speed Grade Vertical Device Migration
Early System and Board Planning x
Early Power Estimation Temperature Sensing for Thermal Management Voltage Sensor Planning for Device Configuration Planning for On-Chip Debugging
Planning for Device Configuration x
Configuration Scheme Selection Configuration Features Quartus Prime Configuration Settings
Configuration Scheme Selection x
Serial Configuration Devices Download Cables Using the Parallel Flash Loader Intel® FPGA IP with MAX Devices
Configuration Features x
Data Compression Design Security Using Configuration Bitstream Encryption Remote System Upgrades SEU Mitigation and CRC Error Checks
Planning for On-Chip Debugging x
On-Chip Debugging Tools Planning Guidelines for Debugging Tools
Pin Connection Considerations for Board Design x
Device Power-Up Power Pin Connections and Power Supplies Configuration Pin Connections Board-Related Quartus Prime Settings Signal Integrity Considerations Board-Level Simulation and Advanced I/O Timing Analysis
Power Pin Connections and Power Supplies x
Decoupling Capacitors PLL and Transceiver Board Design Guidelines
Configuration Pin Connections x
DCLK and TCK Signal Integrity JTAG Pins MSEL Configuration Mode Pins Other Configuration Pins
Board-Related Quartus Prime Settings x
Device-Wide Output Enable Pin Unused Pins
Signal Integrity Considerations x
High-Speed Board Design Voltage Reference Pins Simultaneous Switching Noise I/O Termination
I/O and Clock Planning x
Making FPGA Pin Assignments Early Pin Planning and I/O Assignment Analysis I/O Features and Pin Connections Clock and PLL Selection PLL Feature Guidelines Clock Control Block I/O Simultaneous Switching Noise
I/O Features and Pin Connections x
I/O Signaling Type Selectable I/O Standards and Flexible I/O Banks Memory Interfaces Dual-Purpose and Special Pin Connections Cyclone® 10 GX I/O Features
PLL Feature Guidelines x
Clock Feedback Mode Clock Outputs
Design Entry x
Design Recommendations Using IP Cores Reconfiguration Recommended HDL Coding Styles Register Power-Up Levels and Control Signals Planning for Hierarchical and Team-Based Design
Reconfiguration x
Dynamic Reconfiguration
Planning for Hierarchical and Team-Based Design x
Planning Design Partitions Planning in Bottom-Up and Team-Based Flows Creating a Design Floorplan
Design Implementation, Analysis, Optimization, and Verification x
Selecting a Synthesis Tool Device Resource Utilization Reports Quartus Prime Messages Timing Constraints and Analysis Area and Timing Optimization Preserving Performance and Reducing Compilation Time Simulation Formal Verification Power Analysis Power Optimization
Timing Constraints and Analysis x
Recommended Timing Optimization and Analysis Assignments
Power Optimization x
Device and Design Power Optimization Techniques Quartus Prime Power Optimization Techniques
Device and Design Power Optimization Techniques x
Clock Power Management Memory Power Reduction I/O Power Guidelines
Quartus Prime Power Optimization Techniques x
Power Optimization Advisor
Appendix: Cyclone® 10 GX Transceiver Design Guidelines x
Transceiver PHY Architecture Overview Transceiver Bank Architecture PHY Layer Transceiver Components Transceiver Phase-Locked Loops Clock Generation Block (CGB) Calibration Transceiver Design Flow
PHY Layer Transceiver Components x
The GX Transceiver Channel
Transceiver Phase-Locked Loops x
Advanced Transmit (ATX) PLL Fractional PLL (fPLL) Channel PLL (CMU/CDR PLL)
Intel® Cyclone® 10 GX Device Design Guidelines

Power Pin Connections and Power Supplies

Cyclone® 10 GX devices require various voltage supplies depending on your design requirements. To verify the core voltage, PLL digital power supply, programmable technology voltage, and other voltage supply levels, refer to the Cyclone® 10 GX Device Datasheet.

Cyclone® 10 GX devices support a wide range of industry I/O standards, such as the following VCCIO voltage levels:

  • 3.0 V (only on 3.0 V I/O bank)
  • 2.5 V (only on 3.0 V I/O bank)
  • 1.8 V
  • 1.5 V
  • 1.35 V
  • 1.25 V
  • 1.2 V
Note: The device output pins do not meet the I/O standard specifications if the VCCIO level is out of the recommended operating range for the I/O standard.

Voltage reference (VREF) pins serve as voltage references for certain I/O standards. The VREF pin is used mainly for a voltage bias and does not source or sink much current. The voltage can be created with a regulator or a resistor divider network.

For more information about VCCIO voltages and VREF pins for different I/O banks, refer to “Selectable I/O Standards and Flexible I/O Banks” chapter.

The VREFP_ADC pin is not a power supply pin. It provides the reference voltage for the ADC for the voltage sensor. For better voltage sensor performance, connect VREFP_ADC to an external reference 1.25 V source. Connecting VREFP_ADC to GND actives an on-chip reference source.

Table 19.  Power Pin Connections and Power Supplies Checklist
Number Done? Checklist Item
1   Connect all power pins correctly as specified in the Cyclone 10 GX Device Family Pin Connection Guidelines.
2   Connect VCCIO pins and VREF pins to support each bank’s I/O standards.
3   Explore unique requirements for FPGA power pins or other power pins on your board, and determine which devices on your board can share a power rail.
4   Follow the suggested power supply sharing and isolation guidance, and the specific guidelines for each pin in the Cyclone 10 GX Device Family Pin Connection Guidelines.

Section Content
Decoupling Capacitors
PLL and Transceiver Board Design Guidelines

Related Information
Level Two Title