Visible to Intel only — GUID: mvp1532933311681
Ixiasoft
1. Intel Agilex® 7 Configuration User Guide
2. Intel Agilex® 7 Configuration Details
3. Intel Agilex® 7 Configuration Schemes
4. Including the Reset Release Intel® FPGA IP in Your Design
5. Remote System Update (RSU)
6. Intel Agilex® 7 Configuration Features
7. Intel Agilex® 7 Debugging Guide
8. Intel Agilex® 7 Configuration User Guide Archives
9. Document Revision History for the Intel Agilex® 7 Configuration User Guide
2.1. Intel Agilex® 7 Configuration Timing Diagram
2.2. Configuration Flow Diagram
2.3. Device Response to Configuration and Reset Events
2.4. Additional Clock Requirements for HPS and Transceivers
2.5. Intel Agilex® 7 Configuration Pins
2.6. Configuration Clocks
2.7. Intel Agilex® 7 Configuration Time Estimation
2.8. Generating Compressed .sof File
3.1.1. Avalon® -ST Configuration Scheme Hardware Components and File Types
3.1.2. Enabling Avalon-ST Device Configuration
3.1.3. The AVST_READY Signal
3.1.4. RBF Configuration File Format
3.1.5. Avalon-ST Single-Device Configuration
3.1.6. Debugging Guidelines for the Avalon® -ST Configuration Scheme
3.1.7. IP for Use with the Avalon® -ST Configuration Scheme: Intel FPGA Parallel Flash Loader II IP Core
3.1.7.4.1. PFL II IP Recommended Design Constraints to FPGA Avalon-ST Pins
3.1.7.4.2. PFL II IP Recommended Design Constraints for Using QSPI Flash
3.1.7.4.3. PFL II IP Recommended Design Constraints for using CFI Flash
3.1.7.4.4. PFL II IP Recommended Constraints for Other Input Pins
3.1.7.4.5. PFL II IP Recommended Constraints for Other Output Pins
3.2.1. AS Configuration Scheme Hardware Components and File Types
3.2.2. AS Single-Device Configuration
3.2.3. AS Using Multiple Serial Flash Devices
3.2.4. AS Configuration Timing Parameters
3.2.5. Skew Tolerance Guidelines
3.2.6. Programming Serial Flash Devices
3.2.7. Serial Flash Memory Layout
3.2.8. AS_CLK
3.2.9. Active Serial Configuration Software Settings
3.2.10. Intel® Quartus® Prime Programming Steps
3.2.11. Debugging Guidelines for the AS Configuration Scheme
5.1. Remote System Update Functional Description
5.2. Guidelines for Performing Remote System Update Functions for Non-HPS
5.3. Commands and Responses
5.4. Quad SPI Flash Layout
5.5. Generating Remote System Update Image Files Using the Programming File Generator
5.6. Remote System Update from FPGA Core Example
5.7. Debugging Guidelines for RSU Configuration
5.6.1. Prerequisites
5.6.2. Creating Initial Flash Image Containing Bitstreams for Factory Image and One Application Image
5.6.3. Programming Flash Memory with the Initial Remote System Update Image
5.6.4. Reconfiguring the Device with an Application or Factory Image
5.6.5. Adding an Application Image
5.6.6. Removing an Application Image
7.1. Configuration Debugging Checklist
7.2. Intel Agilex® 7 Configuration Architecture Overview
7.3. Understanding Configuration Status Using quartus_pgm command
7.4. Configuration File Format Differences
7.5. Understanding SEUs
7.6. Reading the Unique 64-Bit CHIP ID
7.7. E-Tile Transceivers May Fail To Configure
7.8. Understanding and Troubleshooting Configuration Pin Behavior
Visible to Intel only — GUID: mvp1532933311681
Ixiasoft
5.6.1. Prerequisites
To run this remote system update example, your system must meet the following hardware and software requirements:
- You should create and download this example to the Intel Agilex® 7 SoC Development Kit.
- Your design should include the Mailbox Client Intel® FPGA IP that connects to a JTAG to Avalon® Master Bridge as shown the Platform Designer system. The JTAG to Avalon® Master Bridge acts as the remote system update host controller for your factory and application images.
- In addition, your design must include the Reset Release Intel® FPGA IP. This component holds the design in reset until the entire FPGA fabric has entered user mode.
- The ninit_done_reset and reset_bridge_1 components create a two-stage reset synchronizer to release the Mailbox Client Intel® FPGA IP and JTAG to Avalon Master Bridge Intel® FPGA IP from reset when the device configuration is complete and the device is in user mode.
- The ninit_done output signal from Reset Release IP gates this reset by connecting to the ninit_done_reset in_reset pin.
- The reset_in Reset Bridge Intel® FPGA IP provides a user mode reset. In this design, the exported resetpin connects to application logic.
-
Figure 73. Required Communication and Host Components for the Remote System Update Design Example