Visible to Intel only — GUID: gwf1474384359305
Ixiasoft
1. Release Information
2. External Memory Interfaces Cyclone® 10 GX FPGA IP Introduction
3. Cyclone® 10 GX EMIF IP Product Architecture
4. Cyclone® 10 GX EMIF IP End-User Signals
5. Cyclone® 10 GX EMIF – Simulating Memory IP
6. Cyclone® 10 GX EMIF IP for DDR3
7. Cyclone® 10 GX EMIF IP for LPDDR3
8. Cyclone® 10 GX EMIF IP Timing Closure
9. Optimizing Controller Performance
10. Cyclone® 10 GX EMIF IP Debugging
11. External Memory Interfaces Cyclone® 10 GX FPGA IP User Guide Archives
12. Document Revision History for Cyclone® 10 GX External Memory Interfaces FPGA IP User Guide
4.1.1.1. pll_ref_clk for DDR3
4.1.1.2. pll_locked for DDR3
4.1.1.3. pll_extra_clk_0 for DDR3
4.1.1.4. pll_extra_clk_1 for DDR3
4.1.1.5. pll_extra_clk_2 for DDR3
4.1.1.6. pll_extra_clk_3 for DDR3
4.1.1.7. oct for DDR3
4.1.1.8. mem for DDR3
4.1.1.9. status for DDR3
4.1.1.10. afi_reset_n for DDR3
4.1.1.11. afi_clk for DDR3
4.1.1.12. afi_half_clk for DDR3
4.1.1.13. afi for DDR3
4.1.1.14. emif_usr_reset_n for DDR3
4.1.1.15. emif_usr_clk for DDR3
4.1.1.16. emif_usr_reset_n_sec for DDR3
4.1.1.17. emif_usr_clk_sec for DDR3
4.1.1.18. cal_debug_reset_n for DDR3
4.1.1.19. cal_debug_clk for DDR3
4.1.1.20. cal_debug_out_reset_n for DDR3
4.1.1.21. cal_debug_out_clk for DDR3
4.1.1.22. clks_sharing_master_out for DDR3
4.1.1.23. clks_sharing_slave_in for DDR3
4.1.1.24. clks_sharing_slave_out for DDR3
4.1.1.25. ctrl_amm for DDR3
4.1.1.26. ctrl_auto_precharge for DDR3
4.1.1.27. ctrl_user_priority for DDR3
4.1.1.28. ctrl_ecc_user_interrupt for DDR3
4.1.1.29. ctrl_ecc_readdataerror for DDR3
4.1.1.30. ctrl_mmr_slave for DDR3
4.1.1.31. cal_debug for DDR3
4.1.1.32. cal_debug_out for DDR3
4.1.2.1. pll_ref_clk for LPDDR3
4.1.2.2. pll_locked for LPDDR3
4.1.2.3. pll_extra_clk_0 for LPDDR3
4.1.2.4. pll_extra_clk_1 for LPDDR3
4.1.2.5. pll_extra_clk_2 for LPDDR3
4.1.2.6. pll_extra_clk_3 for LPDDR3
4.1.2.7. oct for LPDDR3
4.1.2.8. mem for LPDDR3
4.1.2.9. status for LPDDR3
4.1.2.10. afi_reset_n for LPDDR3
4.1.2.11. afi_clk for LPDDR3
4.1.2.12. afi_half_clk for LPDDR3
4.1.2.13. afi for LPDDR3
4.1.2.14. emif_usr_reset_n for LPDDR3
4.1.2.15. emif_usr_clk for LPDDR3
4.1.2.16. cal_debug_reset_n for LPDDR3
4.1.2.17. cal_debug_clk for LPDDR3
4.1.2.18. cal_debug_out_reset_n for LPDDR3
4.1.2.19. cal_debug_out_clk for LPDDR3
4.1.2.20. clks_sharing_master_out for LPDDR3
4.1.2.21. clks_sharing_slave_in for LPDDR3
4.1.2.22. clks_sharing_slave_out for LPDDR3
4.1.2.23. ctrl_user_priority for LPDDR3
4.1.2.24. ctrl_mmr_slave for LPDDR3
4.1.2.25. cal_debug for LPDDR3
4.1.2.26. cal_debug_out for LPDDR3
4.4.1. ctrlcfg0
4.4.2. ctrlcfg1
4.4.3. dramtiming0
4.4.4. sbcfg1
4.4.5. caltiming0
4.4.6. caltiming1
4.4.7. caltiming2
4.4.8. caltiming3
4.4.9. caltiming4
4.4.10. caltiming9
4.4.11. dramaddrw
4.4.12. sideband0
4.4.13. sideband1
4.4.14. sideband2
4.4.15. sideband3
4.4.16. sideband4
4.4.17. sideband5
4.4.18. sideband6
4.4.19. sideband7
4.4.20. sideband8
4.4.21. sideband9
4.4.22. sideband10
4.4.23. sideband11
4.4.24. sideband12
4.4.25. sideband13
4.4.26. dramsts
4.4.27. niosreserve0
4.4.28. niosreserve1
4.4.29. ecc3: ECC Error and Interrupt Configuration
4.4.30. ecc4: Status and Error Information
4.4.31. ecc5: Address of Most Recent SBE/DBE
4.4.32. ecc6: Address of Most Recent Correction Command Dropped
6.1.1. Intel Cyclone 10 GX EMIF IP DDR3 Parameters: General
6.1.2. Intel Cyclone 10 GX EMIF IP DDR3 Parameters: Memory
6.1.3. Intel Cyclone 10 GX EMIF IP DDR3 Parameters: Mem I/O
6.1.4. Intel Cyclone 10 GX EMIF IP DDR3 Parameters: FPGA I/O
6.1.5. Intel Cyclone 10 GX EMIF IP DDR3 Parameters: Mem Timing
6.1.6. Intel Cyclone 10 GX EMIF IP DDR3 Parameters: Board
6.1.7. Intel Cyclone 10 GX EMIF IP DDR3 Parameters: Controller
6.1.8. Intel Cyclone 10 GX EMIF IP DDR3 Parameters: Diagnostics
6.1.9. Intel Cyclone 10 GX EMIF IP DDR3 Parameters: Example Designs
7.1.1. Intel Cyclone 10 GX EMIF IP LPDDR3 Parameters: General
7.1.2. Intel Cyclone 10 GX EMIF IP LPDDR3 Parameters: Memory
7.1.3. Intel Cyclone 10 GX EMIF IP LPDDR3 Parameters: Mem I/O
7.1.4. Intel Cyclone 10 GX EMIF IP LPDDR3 Parameters: FPGA I/O
7.1.5. Intel Cyclone 10 GX EMIF IP LPDDR3 Parameters: Mem Timing
7.1.6. Intel Cyclone 10 GX EMIF IP LPDDR3 Parameters: Board
7.1.7. Intel Cyclone 10 GX EMIF IP LPDDR3 Parameters: Controller
7.1.8. Intel Cyclone 10 GX EMIF IP LPDDR3 Parameters: Diagnostics
7.1.9. Intel Cyclone 10 GX EMIF IP LPDDR3 Parameters: Example Designs
9.4.1. Auto-Precharge Commands
9.4.2. Latency
9.4.3. Calibration
9.4.4. Bank Interleaving
9.4.5. Additive Latency and Bank Interleaving
9.4.6. User-Controlled Refresh
9.4.7. Frequency of Operation
9.4.8. Series of Reads or Writes
9.4.9. Data Reordering
9.4.10. Starvation Control
9.4.11. Command Reordering
9.4.12. Bandwidth
9.4.13. Enable Command Priority Control
10.1. Interface Configuration Performance Issues
10.2. Functional Issue Evaluation
10.3. Timing Issue Characteristics
10.4. Verifying Memory IP Using the Signal Tap II Logic Analyzer
10.5. Hardware Debugging Guidelines
10.6. Categorizing Hardware Issues
10.7. Debugging Cyclone® 10 GX EMIF IP
10.8. Using the Traffic Generator with the Generated Design Example
10.5.1. Create a Simplified Design that Demonstrates the Same Issue
10.5.2. Measure Power Distribution Network
10.5.3. Measure Signal Integrity and Setup and Hold Margin
10.5.4. Vary Voltage
10.5.5. Operate at a Lower Speed
10.5.6. Determine Whether the Issue Exists in Previous Versions of Software
10.5.7. Determine Whether the Issue Exists in the Current Version of Software
10.5.8. Try A Different PCB
10.5.9. Try Other Configurations
10.5.10. Debugging Checklist
Visible to Intel only — GUID: gwf1474384359305
Ixiasoft
6.2.1. Equations for DDR3 Board Skew Parameters
Parameter | Description/Equation |
---|---|
Maximum CK delay to DIMM/device | The delay of the longest CK trace from the FPGA to any DIMM/device.
|
Maximum DQS delay to DIMM/device | The delay of the longest DQS trace from the FPGA to the DIMM/device.
|
Average delay difference between DQS and CK | The average delay difference between the DQS signals and the CK signal, calculated by averaging the longest and smallest DQS delay minus the CK delay. Positive values represent DQS signals that are longer than CK signals and negative values represent DQS signals that are shorter than CK signals. The Quartus Prime software uses this skew to optimize the delay of the DQS signals for appropriate setup and hold margins.
|
Maximum Board skew within DQS group | The largest skew between all DQ and DM pins in a DQS group. Enter your board skew only. Package skew is calculated automatically, based on the memory interface configuration, and added to this value. This value affects the read capture and write margins.
|
Maximum skew between DQS groups | The largest skew between DQS signals in different DQS groups.
|
Maximum system skew within address/command bus |
|
Average delay difference between address/command and CK | A value equal to the average of the longest and smallest address/command signal delays, minus the delay of the CK signal. The value can be positive or negative. The average delay difference between the address/command and CK is expressed by the following equation:
|
Maximum delay difference between DIMMs/devices | The largest propagation delay on DQ signals between ranks. For example, in a two-rank configuration where you place DIMMs in different slots there is also a propagation delay for DQ signals going to and coming back from the furthest DIMM compared to the nearest DIMM. This parameter is applicable only when there is more than one rank.Maxr { max n,m [(DQn_r path delay– DQn_r+1 path delay), (DQSm_r path delay– DQSm_r+1 path delay)]} Where n is the number of DQ, m is the number of DQS and r is number of rank of DIMM/device . |