F-Tile Interlaken Intel® FPGA IP User Guide

Download PDF
ID 683622
Date 10/04/2021
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About this IP Core 2. Getting Started 3. Parameter Settings 4. Functional Description 5. Interface Signals 6. IP Registers 7. F-Tile Interlaken Intel® FPGA IP User Guide Archives 8. Document Revision History for F-Tile Interlaken Intel® FPGA IP User Guide
1. About this IP Core x
1.1. Features 1.2. Device Family Support 1.3. Performance and Resource Utilization 1.4. Round-trip Latency 1.5. Release Information
2. Getting Started x
2.1. Installing and Licensing Intel® FPGA IP Cores 2.2. Generated File Structure 2.3. Specifying the IP Core Parameters and Options 2.4. Reference and System PLL Clock for your IP Design 2.5. Simulating the IP Core 2.6. Compiling the Full Design and Programming the FPGA
2.1. Installing and Licensing Intel® FPGA IP Cores x
2.1.1. Intel® FPGA IP Evaluation Mode
2.4. Reference and System PLL Clock for your IP Design x
2.4.1. System PLL Configuration
4. Functional Description x
4.1. Data Path Flow 4.2. Modes of Operation 4.3. Performance 4.4. IP Reset 4.5. M20K ECC Support 4.6. Out-of-Band Flow Control
4.1. Data Path Flow x
4.1.1. Interlaken TX Path 4.1.2. Interlaken RX Path
4.1.1. Interlaken TX Path x
4.1.1.1. Transmit Path Blocks 4.1.1.2. In-Band Calendar Bits on Transmit Side
4.1.2. Interlaken RX Path x
4.1.2.1. Receive Path Blocks 4.1.2.2. In-Band Calendar Bits on Receive Side 4.1.2.3. RX Errored Packet Handling
4.1.2.3. RX Errored Packet Handling x
4.1.2.3.1. Example With Errors and In-Band Calendar Bits
4.2. Modes of Operation x
4.2.1. Interleaved and Packet Modes 4.2.2. Multi-Segment Mode
4.2.1. Interleaved and Packet Modes x
4.2.1.1. Transmit User Data Interface Examples 4.2.1.2. Receive User Data Interface Example
4.2.2. Multi-Segment Mode x
4.2.2.1. Multi-Segment Interface Example
5. Interface Signals x
5.1. Clock and Reset Interface Signals 5.2. Transmit User Interface Signals 5.3. Receive User Interface Signals 5.4. Management Interface Signals 5.5. Reconfiguration Interface Signals 5.6. Interlaken Link and Miscellaneous Signals
1. About this IP Core
2. Getting Started
3. Parameter Settings
4. Functional Description
5. Interface Signals
6. IP Registers
7. F-Tile Interlaken Intel® FPGA IP User Guide Archives
8. Document Revision History for F-Tile Interlaken Intel® FPGA IP User Guide

4.4. IP Reset

The Interlaken IP core variations have a single asynchronous reset, the reset_n signal. The Interlaken IP core manages the initialization sequence internally. After you de-assert reset_n (raise it after asserting it low), the IP core automatically goes through the entire reset sequence.

The reset_n signal only reset the IP core, while the tx_rst_n and rx_rst_n signals reset the soft reset controller of the F-tile.

The tx_rst_ack_n and rx_rst_ack_n are active low asynchronous reset acknowledge signals for F-tile which indicate that the soft reset controller has successfully entered reset mode and you can now release the reset_n, tx_rst_n, and rx_rst_n signals. The tx_rst_ack_n and rx_rst_ack_n signals stay low until you release the tx_rst_n, and rx_rst_n signals respectively.
Figure 18. Reset Timing Diagram

Following completion of the reset sequence internally, the Interlaken IP core begins link initialization. If your IP core and its Interlaken link partner initialize the link successfully, you can observe the assertion of the lane and link status signals according to the Interlaken specification. For example, you can monitor the tx_lanes_aligned, sync_locked, word_locked, and rx_lanes_aligned output status signals.

For details on transceiver initialization, please refer to the F-Tile Architecture PHY IP User Guide.

Level Two Title