Multi Channel DMA Intel® FPGA IP for PCI Express Design Example User Guide

Download PDF
ID 683517
Date 4/29/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Introduction 2. Design Example Detailed Description 3. Design Example Quick Start Guide 4. User Guide Archives 5. Revision History for the Multi Channel DMA Intel FPGA IP for PCI Express Design Example User Guide
1. Introduction x
1.1. Terms and Acronyms 1.2. MCDMA IP Modes
2. Design Example Detailed Description x
2.1. Design Example Overview 2.2. Hardware and Software Requirements 2.3. PIO Using MCDMA Bypass Mode 2.4. Avalon-ST Packet Generate/Check 2.5. Avalon-ST Device-side Packet Loopback 2.6. Avalon-MM DMA 2.7. BAM_BAS Traffic Generator and Checker 2.8. External Descriptor Controller
2.1. Design Example Overview x
2.1.1. MCDMA H-Tile Design Examples for Endpoint 2.1.2. MCDMA P-Tile Design Examples for Endpoint 2.1.3. MCDMA F-Tile Design Examples for Endpoint
2.3. PIO Using MCDMA Bypass Mode x
2.3.1. Avalon-ST PIO Using MCDMA Bypass Mode 2.3.2. Avalon-MM PIO Using MCDMA Bypass mode
2.3.1. Avalon-ST PIO Using MCDMA Bypass Mode x
2.3.1.1. Four-Port Avalon-ST PIO Using MCDMA Bypass Mode 2.3.1.2. Single-Port Avalon-ST PIO Using MCDMA Bypass Mode
2.3.1.1. Four-Port Avalon-ST PIO Using MCDMA Bypass Mode x
2.3.1.1.1. Simulation Result 2.3.1.1.2. Hardware Test Result
2.3.2. Avalon-MM PIO Using MCDMA Bypass mode x
2.3.2.1. Simulation Results 2.3.2.2. Hardware Test Results
2.4. Avalon-ST Packet Generate/Check x
2.4.1. Four-Port Avalon-ST Packet Generate/Check 2.4.2. Single-Port Avalon-ST Packet Generate/Check
2.4.1. Four-Port Avalon-ST Packet Generate/Check x
2.4.1.1. Simulation Results 2.4.1.2. Hardware Test Results
2.4.2. Single-Port Avalon-ST Packet Generate/Check x
2.4.2.1. Simulation Waveforms 2.4.2.2. Simulation Log
2.5. Avalon-ST Device-side Packet Loopback x
2.5.1. Simulation Results 2.5.2. Hardware Test Results
2.6. Avalon-MM DMA x
2.6.1. Simulation Results 2.6.2. Hardware Test Results
2.7. BAM_BAS Traffic Generator and Checker x
2.7.1. BAM_BAS Traffic Generator and Checker Example Design Register Map
2.8. External Descriptor Controller x
2.8.1. Registers 2.8.2. Hardware Test Results
2.8.1. Registers x
2.8.1.1. GCSR Registers (Base address 64’h00000) 2.8.1.2. QCSR Registers(Base address 64’h10000)
3. Design Example Quick Start Guide x
3.1. Design Example Directory Structure 3.2. Generating the Example Design using Intel® Quartus® Prime 3.3. Simulating the Design Example 3.4. Compiling the Example Design in Intel® Quartus® Prime 3.5. Running the Design Example Application on a Hardware Setup
3.2. Generating the Example Design using Intel® Quartus® Prime x
3.2.1. Procedure
3.3. Simulating the Design Example x
3.3.1. Testbench Overview 3.3.2. Supported Simulators 3.3.3. Example Testbench Flow for DMA Test with Avalon-ST Packet Generate/Check Design Example 3.3.4. Run the Simulation Script 3.3.5. View the Results
3.5. Running the Design Example Application on a Hardware Setup x
3.5.1. Program the FPGA 3.5.2. Quick Start Guide
3.5.2. Quick Start Guide x
3.5.2.1. Software Test Setup 3.5.2.2. Driver Support 3.5.2.3. MCDMA Custom Driver 3.5.2.4. MCDMA DPDK Poll Mode Driver 3.5.2.5. MCDMA Kernel Mode Character Device Driver 3.5.2.6. MCDMA Kernel Mode Network Device Driver
3.5.2.3. MCDMA Custom Driver x
3.5.2.3.1. Prerequisites 3.5.2.3.2. Software Setup 3.5.2.3.3. Run the Reference Example Application 3.5.2.3.4. Testing Bitstream Configuration beyond 256 Channels 3.5.2.3.5. External Descriptor Mode Verification
3.5.2.3.1. Prerequisites x
3.5.2.3.1.1. Configuration Changes from BIOS 3.5.2.3.1.2. External Packages 3.5.2.3.1.3. Set the Boot Parameters
3.5.2.3.2. Software Setup x
3.5.2.3.2.1. Installing the Linux Kernel Driver 3.5.2.3.2.2. Build and Install User Space Library 3.5.2.3.2.3. Enabling VFs and Create Guest VM by Using QEMU 3.5.2.3.2.4. Establish Communication Between Host and QEMU
3.5.2.3.3. Run the Reference Example Application x
3.5.2.3.3.1. Meta Data Test 3.5.2.3.3.2. BAM Test 3.5.2.3.3.3. BAS Test 3.5.2.3.3.4. Packet Gen Test
3.5.2.4. MCDMA DPDK Poll Mode Driver x
3.5.2.4.1. Prerequisites 3.5.2.4.2. Install PMD and Test Application 3.5.2.4.3. Run the Reference Example Application
3.5.2.4.1. Prerequisites x
3.5.2.4.1.1. Set the Boot Parameters 3.5.2.4.1.2. Configuration Changes from BIOS 3.5.2.4.1.3. Install and Build Testpmd
3.5.2.4.2. Install PMD and Test Application x
3.5.2.4.2.1. Create VM Environment
3.5.2.4.3. Run the Reference Example Application x
3.5.2.4.3.1. Example of Verifying on an AVMM Design 3.5.2.4.3.2. BAM Test 3.5.2.4.3.3. BAS Test
3.5.2.5. MCDMA Kernel Mode Character Device Driver x
3.5.2.5.1. Prerequisites 3.5.2.5.2. Software Setup 3.5.2.5.3. Examples
3.5.2.5.1. Prerequisites x
3.5.2.5.1.1. Host Configuration 3.5.2.5.1.2. Set the Boot Parameters
3.5.2.5.2. Software Setup x
3.5.2.5.2.1. Build and Install Kernel Driver 3.5.2.5.2.2. Build and Install Libmcmem 3.5.2.5.2.3. Build Testapp 3.5.2.5.2.4. Configure Kernel Driver 3.5.2.5.2.5. Configure Libmcmem 3.5.2.5.2.6. Configure Testapp
3.5.2.6. MCDMA Kernel Mode Network Device Driver x
3.5.2.6.1. Build and Install Netdev Driver 3.5.2.6.2. Enable VFs if SRIOV is Supported 3.5.2.6.3. Configure the Number of Channels Supported on the Device 3.5.2.6.4. Configure the MTU Value 3.5.2.6.5. Configure the Device Communication 3.5.2.6.6. Configure Transmit Queue Selection Mechanism 3.5.2.6.7. Test Procedure by Using Name Space Environment 3.5.2.6.8. PIO Test
3.5.2.6.6. Configure Transmit Queue Selection Mechanism x
3.5.2.6.6.1. MCDMA Queue Selection 3.5.2.6.6.2. Transmit Packet Steering (XPS) 3.5.2.6.6.3. Default
1. Introduction
2. Design Example Detailed Description
3. Design Example Quick Start Guide
4. User Guide Archives
5. Revision History for the Multi Channel DMA Intel FPGA IP for PCI Express Design Example User Guide

2.8. External Descriptor Controller

External descriptor controller example design supports descriptor fetching and queue management along with MCDMA IP core in Data Mover mode of operations. Example design supports the following features:
  • Total 16 DMA channels (16 H2D queues and 16 D2H queues)
  • Supports separate descriptor command queues for H2D and D2H Data Movers
  • Supports Writeback (WB) as descriptor completion mechanism
  • No Interrupt Support
The figure below is the high level block diagram of example design.
Figure 35. High Level Block Diagram of Example Design
The figure below is the internal representation of external descriptor controller block.
Figure 36. External Descriptor Controller Example Design

Global/Queue CSR: Implements the global CSR and Queue CSR registers required for controlling the DMA operation. Read/Write access to these registers happen through BAM interface of MCDMA IP. For details about the registers, refer to the Registers section.

H2D/D2H Descriptor Fetch: This block generates descriptor fetch commands on h2ddm_desc interface, based on the context in QCSR registers.

Descriptor Completion Processing: This block processes the received descriptor completion packets on h2ddm_desc_cmpl interface for the descriptor fetch request send to MCDMA and stores the received descriptors in corresponding descriptor queue buffers (H2D/D2H Descriptor Queue). These fetched descriptors get queued, and corresponding data mover commands are sent to MCDMA IP though h2ddm_desc or d2hdm_desc interface.

Descriptor Status Processing: This block processes the status information received on h2ddm_desc_status and d2hdm_desc_status interface and generates appropriate writeback commands to MCDMA IP on d2hdm_desc interface.

Descriptor Fetch operation

The descriptor fetch process is described below:

  1. Software updates the Queue context registers in QCSR and update the Tail pointer register (offset 0x10 for D2H; offset 0x90 for H2D).
  2. H2D/D2H Descriptor fetch block detects Tail pointer register update and generate descriptor fetch commands on h2ddm_desc interface of MCDMA to get descriptors from host memory.
  3. The number of descriptors to be fetched are determined by difference between Head pointer (offset 0x18 for D2H; offset 0x98 for H2D) and Tail pointer (offset 0x10 for D2H; offset 0x90 for H2D).
  4. The Head pointer register (offset 0x18 for D2H; offset 0x98 for H2D) is updated based on number of descriptors fetched.
  5. MCDMA provides received descriptor completions on h2ddm_desc_cmpl interface.
  6. The received descriptors are stored on respective Queue buffers (H2D/D2H Descriptor Queue).
  7. The descriptor fetch process happens for multiple queues in a round-robin arbitration scheme.

H2D Data movement operation

  1. Descriptors from H2D Descriptor Queue are pulled out, translated to corresponding data mover commands, and sent to MCDMA though h2ddm_desc interface.
  2. Data transfer happens from Host memory to DMA_MEM though H2D Data Mover AVMM Write master.
  3. Once data transfer is completed, MCDMA sends status on h2ddm_desc_status interface.
  4. The status information is processed by Descriptor Status Processing block to generate appropriate writeback commands to MCDMA on d2hdm_desc interface.
  5. The Completed pointer register (offset 0xA8 for H2D) is updated based on number of descriptors processed.
  6. This flow continues for all descriptors in the H2D Descriptor Queue.

D2H Data movement operation

  1. Descriptors from D2H Descriptor Queue are pulled out, translated to corresponding data mover commands, and sent to MCDMA though d2hdm_desc interface.
  2. Data transfer happens from DMA_MEM to Host memory though D2H Data Mover AVMM Read master.
  3. Once data transfer is completed, MCDMA sends status on d2hdm_desc_status interface.
  4. The status information is processed by Descriptor Status Processing block to generate appropriate writeback commands to MCDMA on d2hdm_desc interface.
  5. The Completed pointer register (offset 0x28 for D2H) is updated based on number of descriptors processed.
  6. This flow continues for all descriptors in the D2H Descriptor Queue.
The differences between main MCDMA and example design are shown in the table below.
Table 16.  Differences between main MCDMA and Example Design
Feature Main MCDMA External Descriptor Controller Example Design

DMA Channels

Up to 2K

Fixed 16

SRIOV

Yes

No

MSI-X

Yes

No

(MSI-X may be supported in future release)

Writeback

Yes

Yes

Queue CSR

Yes

Yes

(For details, see register tables)

MSI

No

No

Descriptor Link bit

Yes

No

(The descriptors are formed continuously and in consecutive locations and provided with starting address in the QCSR)

The following table describes the simplified Host descriptor.
Note: Only the descriptor format is the same for D2H and H2D, and the descriptors are in a separate ring.
Table 17.  Host descriptor format
Name Width Description

SRC_ADDR[63:0]

64

Source address of allocated buffer read by DMA.

DEST_ADDR[127:64]

64

Destination address of allocated buffer written by DMA.

PYLD_CNT[147:128]

20

DMA payload size in bytes. Max 1MB, with 20’h0 indicating 1MB.

RSRV[159:148]

12

Reserved

DESC_IDX [175:160]

16

Unique Identifier for each descriptor, the  same number will be applied to Q_COMPLETED_POINTER.

Same as descriptor count which is used as tail pointer.

For example, descriptor count starts from 1 to 128 for 128 descriptors in a 4K page.

MSIX_EN[176]

1

Enable MSIX

WB_EN[177]

1

Enable Writeback

RSRVD [255:178]

78

Reserved

Section Content
Registers
Hardware Test Results

Level Two Title