Stratix® 10 Power Management User Guide

Download PDF
ID 683418
Date 10/29/2024
Public
Document Table of Contents
Document Table of Contents x
1. Stratix® 10 Power Management Overview 2. Stratix® 10 Power Management Architecture and Features 3. Stratix® 10 Power Management and VID Interface Implementation Guide 4. Stratix® 10 Power Management User Guide Archives 5. Document Revision History for the Stratix® 10 Power Management User Guide
2. Stratix® 10 Power Management Architecture and Features x
2.1. Power Consumption 2.2. Power Reduction Techniques and Features 2.3. Power-On Reset Circuitry 2.4. Power Sequencing Considerations for Stratix® 10 Devices 2.5. Power Supply Design
2.1. Power Consumption x
2.1.1. Dynamic Power Equation
2.2. Power Reduction Techniques and Features x
2.2.1. SmartVID Standard Power Devices 2.2.2. Power-Screened Devices 2.2.3. Temperature Compensation 2.2.4. DSP and M20K Power Gating 2.2.5. Clock Gating 2.2.6. Power Sense Line
2.2.1. SmartVID Standard Power Devices x
2.2.1.1. SmartVID Feature Implementation in Stratix® 10 Devices 2.2.1.2. SDM Power Manager
2.2.1.2. SDM Power Manager x
2.2.1.2.1. PMBus Master Mode 2.2.1.2.2. PMBus Slave Mode
2.3. Power-On Reset Circuitry x
2.3.1. Power Supplies Monitored and Not Monitored by the POR Circuitry
2.4. Power Sequencing Considerations for Stratix® 10 Devices x
2.4.1. Power-Up Sequence Requirements for Stratix® 10 Devices 2.4.2. Power-Down Sequence Recommendations and Requirements for Stratix® 10 Devices
3. Stratix® 10 Power Management and VID Interface Implementation Guide x
3.1. Stratix® 10 Power Management and VID Interface Getting Started
3.1. Stratix® 10 Power Management and VID Interface Getting Started x
3.1.1. Specifying Parameters and Options
3.1.1. Specifying Parameters and Options x
3.1.1.1. Configuration Pin Parameters 3.1.1.2. Power Management and VID Parameters 3.1.1.3. Stratix® 10 Power Management and VID Interface QSF Constraint Guide
1. Stratix® 10 Power Management Overview
2. Stratix® 10 Power Management Architecture and Features
3. Stratix® 10 Power Management and VID Interface Implementation Guide
4. Stratix® 10 Power Management User Guide Archives
5. Document Revision History for the Stratix® 10 Power Management User Guide

2.3. Power-On Reset Circuitry

The POR circuitry keeps the Stratix® 10 device in the reset state until the power supply outputs are within the recommended operating range.

A POR event occurs when you power up the Stratix® 10 device until all power supplies monitored by the POR circuitry reach the recommended operating range within the maximum power supply ramp time, tRAMP . If tRAMP is not met, the Stratix® 10 device I/O pins and programming registers remain tri-stated, which may cause device configuration to fail.

Figure 9. Relationship Between tRAMP and POR Delay

The Stratix® 10 POR circuitry uses individual detection circuitry to monitor each of the configuration-related power supplies independently. The POR circuitry is gated by the outputs of all the individual detectors.

POR delay is the time from when the POR trips out to the final reset signal.

The Stratix® 10 device is held in the POR state until all power supplies have passed their trigger point. After power supplies have passed the trigger point, the SDM waits for a configurable delay time and then start device configuration.


Section Content
Power Supplies Monitored and Not Monitored by the POR Circuitry

Level Two Title