Stratix® 10 Power Management User Guide

Download PDF
ID 683418
Date 10/29/2024
Public
Document Table of Contents
Document Table of Contents x
1. Stratix® 10 Power Management Overview 2. Stratix® 10 Power Management Architecture and Features 3. Stratix® 10 Power Management and VID Interface Implementation Guide 4. Stratix® 10 Power Management User Guide Archives 5. Document Revision History for the Stratix® 10 Power Management User Guide
2. Stratix® 10 Power Management Architecture and Features x
2.1. Power Consumption 2.2. Power Reduction Techniques and Features 2.3. Power-On Reset Circuitry 2.4. Power Sequencing Considerations for Stratix® 10 Devices 2.5. Power Supply Design
2.1. Power Consumption x
2.1.1. Dynamic Power Equation
2.2. Power Reduction Techniques and Features x
2.2.1. SmartVID Standard Power Devices 2.2.2. Power-Screened Devices 2.2.3. Temperature Compensation 2.2.4. DSP and M20K Power Gating 2.2.5. Clock Gating 2.2.6. Power Sense Line
2.2.1. SmartVID Standard Power Devices x
2.2.1.1. SmartVID Feature Implementation in Stratix® 10 Devices 2.2.1.2. SDM Power Manager
2.2.1.2. SDM Power Manager x
2.2.1.2.1. PMBus Master Mode Multi-Master Mode 2.2.1.2.2. PMBus Slave Mode
2.3. Power-On Reset Circuitry x
2.3.1. Power Supplies Monitored and Not Monitored by the POR Circuitry
2.4. Power Sequencing Considerations for Stratix® 10 Devices x
2.4.1. Power-Up Sequence Requirements for Stratix® 10 Devices 2.4.2. Power-Down Sequence Recommendations and Requirements for Stratix® 10 Devices
3. Stratix® 10 Power Management and VID Interface Implementation Guide x
3.1. Stratix® 10 Power Management and VID Interface Getting Started
3.1. Stratix® 10 Power Management and VID Interface Getting Started x
3.1.1. Specifying Parameters and Options
3.1.1. Specifying Parameters and Options x
3.1.1.1. Configuration Pin Parameters 3.1.1.2. Power Management and VID Parameters 3.1.1.3. Stratix® 10 Power Management and VID Interface QSF Constraint Guide
1. Stratix® 10 Power Management Overview
2. Stratix® 10 Power Management Architecture and Features
3. Stratix® 10 Power Management and VID Interface Implementation Guide
4. Stratix® 10 Power Management User Guide Archives
5. Document Revision History for the Stratix® 10 Power Management User Guide

2.2.1.2.1. PMBus Master Mode

In the PMBus master mode, during the initial stage, the SDM Power Manager powers up the VCC and VCCP to the voltage level based on the VID-fused value and the device temperature before it starts to configure the FPGA. After entering the user mode (in the monitor stage), the SDM Power Manager monitors temperature changes and decides if the VCC and VCCP output voltage values need to be updated. If voltages require updating, the SDM Power Manager identifies the voltage value based on the fuse values and the current temperature and sends the desired voltage value to the voltage regulators through the PMBus (PWRMGT_SCL and PWRMGT_SDA).

Note: The PMBus mode only supports the 1.8-V I/O standard.
Figure 3. PMBus Master Mode
Table 3.  Supported Commands for the PMBus Master Mode
Command Name Command Code PMBus Transaction Type Number of Bytes
PAGE 2 00h Write byte 1
VOUT_MODE 3 20h Read byte 1
VOUT_COMMAND 21h Write word 2
READ_VOUT 8Bh Read word 2
MFR_ADC_CONTROL 4 D8h Write byte 1

Multi-Master Mode

The PMBus master mode supports the multi-master mode.

When multiple devices start to communicate at the same time, the device writing the most zeros to the bus or the slowest device wins the arbitration. The other devices immediately discontinue any operation on the bus. When there is an on-going bus communication, all devices must detect the communication and not interrupt it. The devices must wait for a stop condition to appear before starting communication to the bus. Once the stop condition is received on the bus, the next device that wins arbitration sends a start condition by pulling the PWRMGT_SDA low to re-initialize the bus communication.

In this mode, all master devices must be multi masters in a multi-master system. Single-master systems may not understand the arbitration and the busy detection mechanisms can cause unpredictable results.

Related Information
2 This is an optional command. This command is only applicable if you turn on the Enable PAGE command parameter. For more information, refer to the Power Management and VID Parameters section.
3 This is an optional command. This command is only applicable if you select the Auto discovery in the Voltage output format parameter. For more information, refer to the Power Management and VID Parameters section.
4 This command is sent when you set the Slave device type parameter to LTM4677 only.
Level Two Title