100G Interlaken Intel® FPGA IP User Guide

Download PDF
ID 683338
Date 9/20/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About This IP Core 2. Getting Started With the 100G Interlaken IP Core 3. 100G Interlaken IP Core Parameter Settings 4. Functional Description 5. 100G Interlaken IP core Signals 6. 100G Interlaken IP Core Register Map 7. 100G Interlaken IP Core Test Features 8. Advanced Parameter Settings 9. Out-of-Band Flow Control in the 100G Interlaken IP core 10. 100G Interlaken IP core User Guide Archives 11. Document Revision History for 100G Interlaken User Guide A. Performance and Fmax Requirements for 100G Ethernet Traffic
1. About This IP Core x
1.1. Features 1.2. Device Family Support 1.3. IP Core Verification 1.4. Performance and Resource Utilization 1.5. Device Speed Grade Support 1.6. Release Information
1.1. Features x
1.1.1. IP Core Supported Combinations of Number of Lanes and Data Rate 1.1.2. IP Core Theoretical Raw Aggregate Bandwidth
2. Getting Started With the 100G Interlaken IP Core x
2.1. Installing and Licensing Intel® FPGA IP Cores 2.2. Specifying the 100G Interlaken IP Core Parameters and Options 2.3. Files Generated for Arria V GZ and Stratix V Variations 2.4. Files Generated for Intel® Arria® 10 Variations 2.5. Simulating the 100G Interlaken IP Core 2.6. Integrating Your IP Core in Your Design 2.7. Compiling the Full Design and Programming the FPGA 2.8. Creating a Signal Tap Debug File to Match Your Design Hierarchy
2.1. Installing and Licensing Intel® FPGA IP Cores x
2.1.1. Intel® FPGA IP Evaluation Mode
2.6. Integrating Your IP Core in Your Design x
2.6.1. Pin Assignments 2.6.2. Transceiver Logical Channel Numbering 2.6.3. Adding the Reconfiguration Controller 2.6.4. Adding the External PLL
2.6.3. Adding the Reconfiguration Controller x
2.6.3.1. Generating the Reconfiguration Controller 2.6.3.2. Connecting the Reconfiguration Controller to the IP Core
3. 100G Interlaken IP Core Parameter Settings x
3.1. Number of Lanes 3.2. Meta Frame Length in Words 3.3. Data Rate 3.4. Transceiver Reference Clock Frequency 3.5. Include Advanced Error Reporting and Handling 3.6. Enable M20K ECC Support 3.7. Include Diagnostic Features 3.8. Enable Native PHY Debug Master Endpoint (NPDME) 3.9. Include In-Band Flow Control Block 3.10. Number of Calendar Pages 3.11. TX Scrambler Seed 3.12. Transfer Mode Selection 3.13. Data Format
4. Functional Description x
4.1. Interfaces Overview 4.2. High Level Block Diagram 4.3. Clocking and Reset Structure for IP Core 4.4. Interleaved and Packet Modes 4.5. Dual Segment Mode 4.6. M20K ECC Support 4.7. 100G Interlaken IP Core Transmit Path 4.8. 100G Interlaken IP Core Receive Path
4.1. Interfaces Overview x
4.1.1. Application Interface 4.1.2. Interlaken Interface 4.1.3. Out‑of‑Band Flow Control Interface 4.1.4. Management Interface 4.1.5. Transceiver Control Interfaces
4.1.5. Transceiver Control Interfaces x
4.1.5.1. Transceiver Reconfiguration Controller Interface 4.1.5.2. Intel® Arria® 10 External PLL Interface 4.1.5.3. Intel® Arria® 10 Transceiver Reconfiguration Interface
4.3. Clocking and Reset Structure for IP Core x
4.3.1. 100G Interlaken IP Core Clock Signals 4.3.2. IP Core Reset 4.3.3. IP Core Reset Sequence with the Reconfiguration Controller
4.7. 100G Interlaken IP Core Transmit Path x
4.7.1. 100G Interlaken IP Core Transmit User Data Interface Examples 4.7.2. 100G Interlaken IP Core In-Band Calendar Bits on Transmit Side 4.7.3. 100G Interlaken IP Core Transmit Path Blocks
4.7.1. 100G Interlaken IP Core Transmit User Data Interface Examples x
4.7.1.1. 100G Interlaken IP Core Interleaved Mode (Segmented Mode) Example 4.7.1.2. 100G Interlaken IP Core Packet Mode Operation Example 4.7.1.3. 100G Interlaken IP Core Back-Pressured Packet Transfer Example 4.7.1.4. 100G Interlaken IP Core Dual Segment Interleaved Data Transfer Transmit Example
4.7.3. 100G Interlaken IP Core Transmit Path Blocks x
4.7.3.1. 100G Interlaken IP Core TX Transmit Buffer 4.7.3.2. 100G Interlaken IP Core TX MAC 4.7.3.3. 100G Interlaken IP Core TX PCS 4.7.3.4. 100G Interlaken IP Core TX PMA
4.8. 100G Interlaken IP Core Receive Path x
4.8.1. 100G Interlaken IP Core Receive User Data Interface Examples 4.8.2. 100G Interlaken IP Core RX Errored Packet Handling 4.8.3. In-Band Calendar Bits on the 100G Interlaken IP Core Receiver User Data Interface 4.8.4. 100G Interlaken IP Core Receive Path Blocks
4.8.1. 100G Interlaken IP Core Receive User Data Interface Examples x
4.8.1.1. 100G Interlaken IP Core Receiver Side Example 4.8.1.2. 100G Interlaken IP Core Dual Segment Interleaved Data Transfer Receive Example
4.8.2. 100G Interlaken IP Core RX Errored Packet Handling x
4.8.2.1. 100G Interlaken IP Core Receiver Side Example With Errors and In-Band Calendar Bits
4.8.4. 100G Interlaken IP Core Receive Path Blocks x
4.8.4.1. 100G Interlaken IP Core RX PMA 4.8.4.2. 100G Interlaken IP Core RX PCS 4.8.4.3. 100G Interlaken IP Core RX MAC 4.8.4.4. 100G Interlaken IP Core RX Regroup Block
5. 100G Interlaken IP core Signals x
5.1. 100G Interlaken IP Core Clock Interface Signals 5.2. 100G Interlaken IP Core Reset Interface Signals 5.3. 100G Interlaken IP Core User Data Transfer Interface Signals 5.4. 100G Interlaken IP Core Interlaken Link and Miscellaneous Interface Signals 5.5. 100G Interlaken IP Core Management Interface 5.6. Device Dependent Signals
5.6. Device Dependent Signals x
5.6.1. Transceiver Reconfiguration Controller Interface Signals 5.6.2. Intel® Arria® 10 External PLL Interface Signals 5.6.3. Intel® Arria® 10 Transceiver Reconfiguration Interface Signals
7. 100G Interlaken IP Core Test Features x
7.1. Internal Serial Loopback Mode 7.2. External Loopback Mode 7.3. PRBS Generation and Validation 7.4. CRC32 Error Injection 7.5. CRC24 Error Injection
7.3. PRBS Generation and Validation x
7.3.1. Setting up PRBS Mode in Arria V and Stratix V Devices 7.3.2. Setting up PRBS Mode in Intel® Arria® 10 Devices
8. Advanced Parameter Settings x
8.1. Hidden Parameters 8.2. Modifying Hidden Parameter Values
8.1. Hidden Parameters x
8.1.1. Include Temp Sense 8.1.2. RXFIFO Address Width 8.1.3. SWAP_TX_LANES and SWAP_RX_LANES (Data Word Lane Swapping)
9. Out-of-Band Flow Control in the 100G Interlaken IP core x
9.1. Out-of-Band Flow Control Block Clocks 9.2. TX Out‑of‑Band Flow Control Signals 9.3. RX Out-of-Band Flow Control Signals
1. About This IP Core
2. Getting Started With the 100G Interlaken IP Core
3. 100G Interlaken IP Core Parameter Settings
4. Functional Description
5. 100G Interlaken IP core Signals
6. 100G Interlaken IP Core Register Map
7. 100G Interlaken IP Core Test Features
8. Advanced Parameter Settings
9. Out-of-Band Flow Control in the 100G Interlaken IP core
10. 100G Interlaken IP core User Guide Archives
11. Document Revision History for 100G Interlaken User Guide
A. Performance and Fmax Requirements for 100G Ethernet Traffic

7.4. CRC32 Error Injection

The 100G Interlaken IP core supports the injection of CRC32 errors on the Interlaken link for validation of the Interlaken link partner's error handling, and for validation of this IP core's error handling in a loopback configuration. Variations that target an Arria V or Stratix V device require that you first enable the feature in the hard PCS; variations that target an Intel® Arria® 10 device do not require this step.

This feature is available if you turn on Include diagnostic features in the 100G Interlaken parameter editor.

To enable the CRC32 error injection feature in your 100G Interlaken IP core that targets an Arria V or Stratix V device, set the value of bit [15] of the hard PCS register at offset 0x138 (offset 0xC from the hard PCS base address of 0x12C) to the value of 1. Ensure you set the register bit using a read-modify-write register access sequence, to avoid modifying the other register fields. This step is not necessary in 100G Interlaken IP core devices that target an Intel® Arria® 10 device, because CRC32 error injection is enabled by default in these variations.

For instructions to program the hard PCS registers in Arria V and Stratix V devices, refer to the Native PHY IP Core chapter for your target device family and to the Transceiver Reconfiguration Controller chapter of the Intel® Transceiver PHY IP Core User Guide.

After you enable the IP core to inject CRC32 errors in the output to the Interlaken link, you can turn on the feature using the 100G Interlaken IP core CRC32_ERR_INJECT register. You must maintain each register bit at the value of 1 for the duration of a Meta Frame, at least, to ensure that the IP core transmits at least one CRC32 error on the corresponding lane.

After your testing is complete, in Arria V and Stratix V devices, you must reset the hard PCS register bit to its default value of zero to enable normal operation.

The 100G Interlaken IP core CRC32 error injection feature does not keep a count of the errors injected.

Related Information
Level Two Title