100G Interlaken Intel® FPGA IP User Guide

Download PDF
ID 683338
Date 9/20/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About This IP Core 2. Getting Started With the 100G Interlaken IP Core 3. 100G Interlaken IP Core Parameter Settings 4. Functional Description 5. 100G Interlaken IP core Signals 6. 100G Interlaken IP Core Register Map 7. 100G Interlaken IP Core Test Features 8. Advanced Parameter Settings 9. Out-of-Band Flow Control in the 100G Interlaken IP core 10. 100G Interlaken IP core User Guide Archives 11. Document Revision History for 100G Interlaken User Guide A. Performance and Fmax Requirements for 100G Ethernet Traffic
1. About This IP Core x
1.1. Features 1.2. Device Family Support 1.3. IP Core Verification 1.4. Performance and Resource Utilization 1.5. Device Speed Grade Support 1.6. Release Information
1.1. Features x
1.1.1. IP Core Supported Combinations of Number of Lanes and Data Rate 1.1.2. IP Core Theoretical Raw Aggregate Bandwidth
2. Getting Started With the 100G Interlaken IP Core x
2.1. Installing and Licensing Intel® FPGA IP Cores 2.2. Specifying the 100G Interlaken IP Core Parameters and Options 2.3. Files Generated for Arria V GZ and Stratix V Variations 2.4. Files Generated for Intel® Arria® 10 Variations 2.5. Simulating the 100G Interlaken IP Core 2.6. Integrating Your IP Core in Your Design 2.7. Compiling the Full Design and Programming the FPGA 2.8. Creating a Signal Tap Debug File to Match Your Design Hierarchy
2.1. Installing and Licensing Intel® FPGA IP Cores x
2.1.1. Intel® FPGA IP Evaluation Mode
2.6. Integrating Your IP Core in Your Design x
2.6.1. Pin Assignments 2.6.2. Transceiver Logical Channel Numbering 2.6.3. Adding the Reconfiguration Controller 2.6.4. Adding the External PLL
2.6.3. Adding the Reconfiguration Controller x
2.6.3.1. Generating the Reconfiguration Controller 2.6.3.2. Connecting the Reconfiguration Controller to the IP Core
3. 100G Interlaken IP Core Parameter Settings x
3.1. Number of Lanes 3.2. Meta Frame Length in Words 3.3. Data Rate 3.4. Transceiver Reference Clock Frequency 3.5. Include Advanced Error Reporting and Handling 3.6. Enable M20K ECC Support 3.7. Include Diagnostic Features 3.8. Enable Native PHY Debug Master Endpoint (NPDME) 3.9. Include In-Band Flow Control Block 3.10. Number of Calendar Pages 3.11. TX Scrambler Seed 3.12. Transfer Mode Selection 3.13. Data Format
4. Functional Description x
4.1. Interfaces Overview 4.2. High Level Block Diagram 4.3. Clocking and Reset Structure for IP Core 4.4. Interleaved and Packet Modes 4.5. Dual Segment Mode 4.6. M20K ECC Support 4.7. 100G Interlaken IP Core Transmit Path 4.8. 100G Interlaken IP Core Receive Path
4.1. Interfaces Overview x
4.1.1. Application Interface 4.1.2. Interlaken Interface 4.1.3. Out‑of‑Band Flow Control Interface 4.1.4. Management Interface 4.1.5. Transceiver Control Interfaces
4.1.5. Transceiver Control Interfaces x
4.1.5.1. Transceiver Reconfiguration Controller Interface 4.1.5.2. Intel® Arria® 10 External PLL Interface 4.1.5.3. Intel® Arria® 10 Transceiver Reconfiguration Interface
4.3. Clocking and Reset Structure for IP Core x
4.3.1. 100G Interlaken IP Core Clock Signals 4.3.2. IP Core Reset 4.3.3. IP Core Reset Sequence with the Reconfiguration Controller
4.7. 100G Interlaken IP Core Transmit Path x
4.7.1. 100G Interlaken IP Core Transmit User Data Interface Examples 4.7.2. 100G Interlaken IP Core In-Band Calendar Bits on Transmit Side 4.7.3. 100G Interlaken IP Core Transmit Path Blocks
4.7.1. 100G Interlaken IP Core Transmit User Data Interface Examples x
4.7.1.1. 100G Interlaken IP Core Interleaved Mode (Segmented Mode) Example 4.7.1.2. 100G Interlaken IP Core Packet Mode Operation Example 4.7.1.3. 100G Interlaken IP Core Back-Pressured Packet Transfer Example 4.7.1.4. 100G Interlaken IP Core Dual Segment Interleaved Data Transfer Transmit Example
4.7.3. 100G Interlaken IP Core Transmit Path Blocks x
4.7.3.1. 100G Interlaken IP Core TX Transmit Buffer 4.7.3.2. 100G Interlaken IP Core TX MAC 4.7.3.3. 100G Interlaken IP Core TX PCS 4.7.3.4. 100G Interlaken IP Core TX PMA
4.8. 100G Interlaken IP Core Receive Path x
4.8.1. 100G Interlaken IP Core Receive User Data Interface Examples 4.8.2. 100G Interlaken IP Core RX Errored Packet Handling 4.8.3. In-Band Calendar Bits on the 100G Interlaken IP Core Receiver User Data Interface 4.8.4. 100G Interlaken IP Core Receive Path Blocks
4.8.1. 100G Interlaken IP Core Receive User Data Interface Examples x
4.8.1.1. 100G Interlaken IP Core Receiver Side Example 4.8.1.2. 100G Interlaken IP Core Dual Segment Interleaved Data Transfer Receive Example
4.8.2. 100G Interlaken IP Core RX Errored Packet Handling x
4.8.2.1. 100G Interlaken IP Core Receiver Side Example With Errors and In-Band Calendar Bits
4.8.4. 100G Interlaken IP Core Receive Path Blocks x
4.8.4.1. 100G Interlaken IP Core RX PMA 4.8.4.2. 100G Interlaken IP Core RX PCS 4.8.4.3. 100G Interlaken IP Core RX MAC 4.8.4.4. 100G Interlaken IP Core RX Regroup Block
5. 100G Interlaken IP core Signals x
5.1. 100G Interlaken IP Core Clock Interface Signals 5.2. 100G Interlaken IP Core Reset Interface Signals 5.3. 100G Interlaken IP Core User Data Transfer Interface Signals 5.4. 100G Interlaken IP Core Interlaken Link and Miscellaneous Interface Signals 5.5. 100G Interlaken IP Core Management Interface 5.6. Device Dependent Signals
5.6. Device Dependent Signals x
5.6.1. Transceiver Reconfiguration Controller Interface Signals 5.6.2. Intel® Arria® 10 External PLL Interface Signals 5.6.3. Intel® Arria® 10 Transceiver Reconfiguration Interface Signals
7. 100G Interlaken IP Core Test Features x
7.1. Internal Serial Loopback Mode 7.2. External Loopback Mode 7.3. PRBS Generation and Validation 7.4. CRC32 Error Injection 7.5. CRC24 Error Injection
7.3. PRBS Generation and Validation x
7.3.1. Setting up PRBS Mode in Arria V and Stratix V Devices 7.3.2. Setting up PRBS Mode in Intel® Arria® 10 Devices
8. Advanced Parameter Settings x
8.1. Hidden Parameters 8.2. Modifying Hidden Parameter Values
8.1. Hidden Parameters x
8.1.1. Include Temp Sense 8.1.2. RXFIFO Address Width 8.1.3. SWAP_TX_LANES and SWAP_RX_LANES (Data Word Lane Swapping)
9. Out-of-Band Flow Control in the 100G Interlaken IP core x
9.1. Out-of-Band Flow Control Block Clocks 9.2. TX Out‑of‑Band Flow Control Signals 9.3. RX Out-of-Band Flow Control Signals
1. About This IP Core
2. Getting Started With the 100G Interlaken IP Core
3. 100G Interlaken IP Core Parameter Settings
4. Functional Description
5. 100G Interlaken IP core Signals
6. 100G Interlaken IP Core Register Map
7. 100G Interlaken IP Core Test Features
8. Advanced Parameter Settings
9. Out-of-Band Flow Control in the 100G Interlaken IP core
10. 100G Interlaken IP core User Guide Archives
11. Document Revision History for 100G Interlaken User Guide
A. Performance and Fmax Requirements for 100G Ethernet Traffic

4.4. Interleaved and Packet Modes

You can configure the 100G Interlaken IP core to accept interleaved data transfers from the application on the TX user data transfer interface, or to not accept interleaved data transfers on this interface. If the IP core can accept interleaved data transfers, it is in Interleaved mode, sometimes also called Segmented mode. If the IP core does not accept interleaved data transfers, it is in Packet mode. The value you specify for the Transfer mode selection parameter in the 100G Interlaken parameter editor determines the IP core transmit mode.

In Packet mode, the 100G Interlaken IP Core performs Optional Scheduling Enhancement based on Section 5.3.2.1.1 of the Interlaken Protocol Specification, Revision 1.2. The IP core ignores the itx_sob and itx_eob signals. Instead, the IP core performs optional enhanced scheduling based on the settings of BurstMax, BurstMin, and BurstShort.

In Interleaved mode, the 100G Interlaken IP Core inserts burst control words on the Interlaken link based on the itx_sob and itx_eob inputs. The internal optional enhanced scheduling is disabled and the BurstMax and BurstMin values are ignored. BurstShort is still in effect. To avoid overflowing the transmit FIFO, you should not send a burst that is longer than 1024 bytes.

In Interleaved mode or in Packet mode, the 100G Interlaken IP core is capable of accepting non-interleaved data on the TX user data transfer interface (itx_din_words). However, if the IP core is in Interleaved mode, the application must drive the itx_sob and itx_eob inputs correctly.

In Interleaved mode or in Packet mode, the 100G Interlaken IP core can generate interleaved data transfers on the RX user data transfer interface (irx_dout_words). The application must be able to accept interleaved data transfers if the Interlaken link partner transmits them on the Interlaken link. In this case, the Interlaken link partner must send traffic in Interleaved mode that conforms with the 100G Interlaken IP core BurstShort value.

Note: The transmitter (link partner) must only send packets with a minimum packet size of 64 bytes.
Related Information
Level Two Title