Pin Mux Control Group Register Descriptions Controls Pin Mux selections NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. Offset: 0x400 EMACIO0 This register is used to control the peripherals connected to emac0_tx_clk Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO1 This register is used to control the peripherals connected to emac0_tx_d0 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO2 This register is used to control the peripherals connected to emac0_tx_d1 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO3 This register is used to control the peripherals connected to emac0_tx_d2 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO4 This register is used to control the peripherals connected to emac0_tx_d3 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO5 This register is used to control the peripherals connected to emac0_rx_d0 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO6 This register is used to control the peripherals connected to emac0_mdio Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO7 This register is used to control the peripherals connected to emac0_mdc Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO8 This register is used to control the peripherals connected to emac0_rx_ctl Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO9 This register is used to control the peripherals connected to emac0_tx_ctl Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO10 This register is used to control the peripherals connected to emac0_rx_clk Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO11 This register is used to control the peripherals connected to emac0_rx_d1 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO12 This register is used to control the peripherals connected to emac0_rx_d2 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO13 This register is used to control the peripherals connected to emac0_rx_d3 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO14 This register is used to control the peripherals connected to emac1_tx_clk Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO15 This register is used to control the peripherals connected to emac1_tx_d0 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO16 This register is used to control the peripherals connected to emac1_tx_d1 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO17 This register is used to control the peripherals connected to emac1_tx_ctl Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO18 This register is used to control the peripherals connected to emac1_rx_d0 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. EMACIO19 This register is used to control the peripherals connected to emac1_rx_d1 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. FLASHIO0 This register is used to control the peripherals connected to sdmmc_cmd Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. FLASHIO1 This register is used to control the peripherals connected to sdmmc_pwren Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. FLASHIO2 This register is used to control the peripherals connected to sdmmc_d0 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. FLASHIO3 This register is used to control the peripherals connected to sdmmc_d1 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. FLASHIO4 This register is used to control the peripherals connected to sdmmc_d4 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. FLASHIO5 This register is used to control the peripherals connected to sdmmc_d5 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. FLASHIO6 This register is used to control the peripherals connected to sdmmc_d6 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. FLASHIO7 This register is used to control the peripherals connected to sdmmc_d7 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. FLASHIO8 This register is used to control the peripherals connected to sdmmc_clk_in Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. FLASHIO9 This register is used to control the peripherals connected to sdmmc_clk Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. FLASHIO10 This register is used to control the peripherals connected to sdmmc_d2 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. FLASHIO11 This register is used to control the peripherals connected to sdmmc_d3 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO0 This register is used to control the peripherals connected to trace_clk Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO1 This register is used to control the peripherals connected to trace_d0 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO2 This register is used to control the peripherals connected to trace_d1 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO3 This register is used to control the peripherals connected to trace_d2 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO4 This register is used to control the peripherals connected to trace_d3 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO5 This register is used to control the peripherals connected to trace_d4 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO6 This register is used to control the peripherals connected to trace_d5 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO7 This register is used to control the peripherals connected to trace_d6 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO8 This register is used to control the peripherals connected to trace_d7 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO9 This register is used to control the peripherals connected to spim0_clk Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO10 This register is used to control the peripherals connected to spim0_mosi Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO11 This register is used to control the peripherals connected to spim0_miso Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO12 This register is used to control the peripherals connected to spim0_ss0 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO13 This register is used to control the peripherals connected to uart0_rx Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO14 This register is used to control the peripherals connected to uart0_tx Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO15 This register is used to control the peripherals connected to i2c0_sda Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO16 This register is used to control the peripherals connected to i2c0_scl Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO17 This register is used to control the peripherals connected to can0_rx Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO18 This register is used to control the peripherals connected to can0_tx Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO19 This register is used to control the peripherals connected to spis1_clk Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO20 This register is used to control the peripherals connected to spis1_mosi Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO21 This register is used to control the peripherals connected to spis1_miso Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO22 This register is used to control the peripherals connected to spis1_ss0 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO23 This register is used to control the peripherals connected to uart1_rx Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO24 This register is used to control the peripherals connected to uart1_tx Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO25 This register is used to control the peripherals connected to i2c1_sda Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO26 This register is used to control the peripherals connected to i2c1_scl Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO27 This register is used to control the peripherals connected to spim0_ss0_alt Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO28 This register is used to control the peripherals connected to spis0_clk Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO29 This register is used to control the peripherals connected to spis0_mosi Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO30 This register is used to control the peripherals connected to spis0_miso Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GENERALIO31 This register is used to control the peripherals connected to spis0_ss0 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO0 This register is used to control the peripherals connected to nand_ale Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO1 This register is used to control the peripherals connected to nand_ce Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO2 This register is used to control the peripherals connected to nand_cle Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO3 This register is used to control the peripherals connected to nand_re Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO4 This register is used to control the peripherals connected to nand_rb Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO5 This register is used to control the peripherals connected to nand_dq0 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO6 This register is used to control the peripherals connected to nand_dq1 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO7 This register is used to control the peripherals connected to nand_dq2 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO8 This register is used to control the peripherals connected to nand_dq3 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO9 This register is used to control the peripherals connected to nand_dq4 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO10 This register is used to control the peripherals connected to nand_dq5 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO11 This register is used to control the peripherals connected to nand_dq6 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO12 This register is used to control the peripherals connected to nand_dq7 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO13 This register is used to control the peripherals connected to nand_wp Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO14 This register is used to control the peripherals connected to nand_we Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO15 This register is used to control the peripherals connected to qspi_io0 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO16 This register is used to control the peripherals connected to qspi_io1 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO17 This register is used to control the peripherals connected to qspi_io2 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO18 This register is used to control the peripherals connected to qspi_io3 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO19 This register is used to control the peripherals connected to qspi_ss0 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO20 This register is used to control the peripherals connected to qpsi_clk Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED1IO21 This register is used to control the peripherals connected to qspi_ss1 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED2IO0 This register is used to control the peripherals connected to emac1_mdio Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED2IO1 This register is used to control the peripherals connected to emac1_mdc Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED2IO2 This register is used to control the peripherals connected to emac1_tx_d2 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED2IO3 This register is used to control the peripherals connected to emac1_tx_d3 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED2IO4 This register is used to control the peripherals connected to emac1_rx_clk Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED2IO5 This register is used to control the peripherals connected to emac1_rx_ctl Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED2IO6 This register is used to control the peripherals connected to emac1_rx_d2 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. MIXED2IO7 This register is used to control the peripherals connected to emac1_rx_d3 Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX48 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 48. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX49 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 49. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX50 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 50. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX51 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 51. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX52 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 52. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX53 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 53. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX54 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 54. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX55 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 55. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX56 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 56. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX57 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 57. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX58 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 58. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX59 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 59. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX60 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 60. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX61 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 61. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX62 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 62. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX63 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 63. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX64 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 64. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX65 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 65. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX66 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 66. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX67 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 67. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX68 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 68. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX69 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 69. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLINMUX70 Some GPIO/LoanIO inputs can be driven by multiple pins. This register selects the input signal for GPIO/LoanIO 70. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX0 Selection between GPIO and LoanIO output and output enable for GPIO0 and LoanIO0. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX1 Selection between GPIO and LoanIO output and output enable for GPIO1 and LoanIO1. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX2 Selection between GPIO and LoanIO output and output enable for GPIO2 and LoanIO2. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX3 Selection between GPIO and LoanIO output and output enable for GPIO3 and LoanIO3. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX4 Selection between GPIO and LoanIO output and output enable for GPIO4 and LoanIO4. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX5 Selection between GPIO and LoanIO output and output enable for GPIO5 and LoanIO5. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX6 Selection between GPIO and LoanIO output and output enable for GPIO6 and LoanIO6. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX7 Selection between GPIO and LoanIO output and output enable for GPIO7 and LoanIO7. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX8 Selection between GPIO and LoanIO output and output enable for GPIO8 and LoanIO8. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX9 Selection between GPIO and LoanIO output and output enable for GPIO9 and LoanIO9. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX10 Selection between GPIO and LoanIO output and output enable for GPIO10 and LoanIO10. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX11 Selection between GPIO and LoanIO output and output enable for GPIO11 and LoanIO11. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX12 Selection between GPIO and LoanIO output and output enable for GPIO12 and LoanIO12. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX13 Selection between GPIO and LoanIO output and output enable for GPIO13 and LoanIO13. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX14 Selection between GPIO and LoanIO output and output enable for GPIO14 and LoanIO14. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX15 Selection between GPIO and LoanIO output and output enable for GPIO15 and LoanIO15. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX16 Selection between GPIO and LoanIO output and output enable for GPIO16 and LoanIO16. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX17 Selection between GPIO and LoanIO output and output enable for GPIO17 and LoanIO17. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX18 Selection between GPIO and LoanIO output and output enable for GPIO18 and LoanIO18. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX19 Selection between GPIO and LoanIO output and output enable for GPIO19 and LoanIO19. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX20 Selection between GPIO and LoanIO output and output enable for GPIO20 and LoanIO20. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX21 Selection between GPIO and LoanIO output and output enable for GPIO21 and LoanIO21. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX22 Selection between GPIO and LoanIO output and output enable for GPIO22 and LoanIO22. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX23 Selection between GPIO and LoanIO output and output enable for GPIO23 and LoanIO23. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX24 Selection between GPIO and LoanIO output and output enable for GPIO24 and LoanIO24. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX25 Selection between GPIO and LoanIO output and output enable for GPIO25 and LoanIO25. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX26 Selection between GPIO and LoanIO output and output enable for GPIO26 and LoanIO26. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX27 Selection between GPIO and LoanIO output and output enable for GPIO27 and LoanIO27. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX28 Selection between GPIO and LoanIO output and output enable for GPIO28 and LoanIO28. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX29 Selection between GPIO and LoanIO output and output enable for GPIO29 and LoanIO29. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX30 Selection between GPIO and LoanIO output and output enable for GPIO30 and LoanIO30. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX31 Selection between GPIO and LoanIO output and output enable for GPIO31 and LoanIO31. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX32 Selection between GPIO and LoanIO output and output enable for GPIO32 and LoanIO32. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX33 Selection between GPIO and LoanIO output and output enable for GPIO33 and LoanIO33. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX34 Selection between GPIO and LoanIO output and output enable for GPIO34 and LoanIO34. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX35 Selection between GPIO and LoanIO output and output enable for GPIO35 and LoanIO35. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX36 Selection between GPIO and LoanIO output and output enable for GPIO36 and LoanIO36. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX37 Selection between GPIO and LoanIO output and output enable for GPIO37 and LoanIO37. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX38 Selection between GPIO and LoanIO output and output enable for GPIO38 and LoanIO38. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX39 Selection between GPIO and LoanIO output and output enable for GPIO39 and LoanIO39. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX40 Selection between GPIO and LoanIO output and output enable for GPIO40 and LoanIO40. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX41 Selection between GPIO and LoanIO output and output enable for GPIO41 and LoanIO41. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX42 Selection between GPIO and LoanIO output and output enable for GPIO42 and LoanIO42. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX43 Selection between GPIO and LoanIO output and output enable for GPIO43 and LoanIO43. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX44 Selection between GPIO and LoanIO output and output enable for GPIO44 and LoanIO44. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX45 Selection between GPIO and LoanIO output and output enable for GPIO45 and LoanIO45. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX46 Selection between GPIO and LoanIO output and output enable for GPIO46 and LoanIO46. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX47 Selection between GPIO and LoanIO output and output enable for GPIO47 and LoanIO47. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX48 Selection between GPIO and LoanIO output and output enable for GPIO48 and LoanIO48. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX49 Selection between GPIO and LoanIO output and output enable for GPIO49 and LoanIO49. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX50 Selection between GPIO and LoanIO output and output enable for GPIO50 and LoanIO50. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX51 Selection between GPIO and LoanIO output and output enable for GPIO51 and LoanIO51. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX52 Selection between GPIO and LoanIO output and output enable for GPIO52 and LoanIO52. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX53 Selection between GPIO and LoanIO output and output enable for GPIO53 and LoanIO53. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX54 Selection between GPIO and LoanIO output and output enable for GPIO54 and LoanIO54. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX55 Selection between GPIO and LoanIO output and output enable for GPIO55 and LoanIO55. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX56 Selection between GPIO and LoanIO output and output enable for GPIO56 and LoanIO56. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX57 Selection between GPIO and LoanIO output and output enable for GPIO57 and LoanIO57. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX58 Selection between GPIO and LoanIO output and output enable for GPIO58 and LoanIO58. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX59 Selection between GPIO and LoanIO output and output enable for GPIO59 and LoanIO59. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX60 Selection between GPIO and LoanIO output and output enable for GPIO60 and LoanIO60. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX61 Selection between GPIO and LoanIO output and output enable for GPIO61 and LoanIO61. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX62 Selection between GPIO and LoanIO output and output enable for GPIO62 and LoanIO62. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX63 Selection between GPIO and LoanIO output and output enable for GPIO63 and LoanIO63. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX64 Selection between GPIO and LoanIO output and output enable for GPIO64 and LoanIO64. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX65 Selection between GPIO and LoanIO output and output enable for GPIO65 and LoanIO65. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX66 Selection between GPIO and LoanIO output and output enable for GPIO66 and LoanIO66. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX67 Selection between GPIO and LoanIO output and output enable for GPIO67 and LoanIO67. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX68 Selection between GPIO and LoanIO output and output enable for GPIO68 and LoanIO68. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX69 Selection between GPIO and LoanIO output and output enable for GPIO69 and LoanIO69. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. GPLMUX70 Selection between GPIO and LoanIO output and output enable for GPIO70 and LoanIO70. These signals drive the Pin Mux. The Pin Mux must be configured to use GPIO/LoanIO in addition to these settings Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. UART0USEFPGA Selection between HPS Pins and FPGA Interface for UART0 signals. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. RGMII1USEFPGA Selection between HPS Pins and FPGA Interface for RGMII1 signals. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. SPIS0USEFPGA Selection between HPS Pins and FPGA Interface for SPIS0 signals. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. I2C0USEFPGA Selection between HPS Pins and FPGA Interface for I2C0 signals. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. SDMMCUSEFPGA Selection between HPS Pins and FPGA Interface for SDMMC signals. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration. There is no support for dynamically changing the Pin Mux selections QSPIUSEFPGA Selection between HPS Pins and FPGA Interface for QSPI signals. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. SPIS1USEFPGA Selection between HPS Pins and FPGA Interface for SPIS1 signals. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. RGMII0USEFPGA Selection between HPS Pins and FPGA Interface for RGMII0 signals. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. UART1USEFPGA Selection between HPS Pins and FPGA Interface for UART1 signals. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. I2C3USEFPGA Selection between HPS Pins and FPGA Interface for I2C3 signals. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. I2C2USEFPGA Selection between HPS Pins and FPGA Interface for I2C2 signals. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. I2C1USEFPGA Selection between HPS Pins and FPGA Interface for I2C1 signals. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. SPIM1USEFPGA Selection between HPS Pins and FPGA Interface for SPIM1 signals. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections. SPIM0USEFPGA Selection between HPS Pins and FPGA Interface for SPIM0 signals. Only reset by a cold reset (ignores warm reset). NOTE: These registers should not be modified after IO configuration.There is no support for dynamically changing the Pin Mux selections.