Agilex™ 7 M-Series Known Issue List

Download PDF
ID 851750
Date 4/18/2025
Public
Document Table of Contents
Document Table of Contents x
1. About This Document 2. Known Issue List for Devices 3. Arm* Cortex*-A53 MPCore and CoreSight* Errata 4. Agilex™ 7 M-Series User Guidelines 5. Document Revision History for the Agilex™ 7 M-Series Known Issue List
2. Known Issue List for Devices x
2.1. FPGA 2.2. EMIF 2.3. Configuration and Security 2.4. Fabric NoC 2.5. Device Power Supply, Core, I/O
2.1. FPGA x
2.1.1. F-Tile 2.1.2. R-Tile
2.1.1. F-Tile x
2.1.1.1. Requirement for F-Tile Devices which are Powered and Unconfigured 2.1.1.2. FGT PAM4 Bounding Solution 2.1.1.3. FGT Transceivers Do Not Support Direct EXTEST JTAG Instruction in Boundary Scan Test 2.1.1.4. F-Tile: Unsuccessful TX Equalization 2.1.1.5. Link May Not Downgrade With Corrupt Lanes (F-Tile) 2.1.1.6. Intermittent Equalization Timeout or Speed Degrade during Link Disable, Hot Reset, and Speed Change 2.1.1.7. Link Fault Detection window of the F-Tile Ethernet Intel FPGA Hard IP in 10GE-1 or 25GE-1 mode 2.1.1.8. FHT PMA Transmitter-to-Receiver Internal Serial Loopback operation for error-free BER results 2.1.1.9. F-Tile Ethernet Intel FPGA Hard IP rst_tx_stats and rst_rx_stats register bits might not function correctly 2.1.1.10. F-Tile Ethernet Intel FPGA Hard IP force_rf register bit might not function correctly 2.1.1.11. F-Tile Ethernet Intel FPGA Hard IP tx_pause_request register bit might not function correctly 2.1.1.12. F-Tile Ethernet Intel FPGA Hard IP PTP statistics might not clear correctly 2.1.1.13. F-Tile Ethernet Intel FPGA Hard IP unable to achieve 100% throughput with some variants
2.1.2. R-Tile x
2.1.2.1. Gen3/Gen4 link might be established without successfully performing Transmit Equalization (TX EQ) 2.1.2.2. Link may not downgrade with corrupt lanes 2.1.2.3. Malformed TLP incorrectly flagged as ECRC error 2.1.2.4. Assertion of PERST / warm reset during the Functional Level Reset results in PCIe* Link Failure 2.1.2.5. No Support for Page Request Services in Port 2 and Port 3 of 4x4 Configuration 2.1.2.6. Multiple Fatal Error Messages 2.1.2.7. PCIe* x4 cores may report Uncorrectable Fatal Error or Malformed TLP 2.1.2.8. Receiver Errors logged during back-to-back Secondary Bus Resets (SBR) operations when running at Gen 2 speed 2.1.2.9. Polling.Active time out during Link Disable-Enable loop tests 2.1.2.10. CXL 1.1 version does not support uncorrectable error reporting when receiving two LLCTRL-Init packet
2.2. EMIF x
2.2.1. DDR5 RDIMM support Description Workaround Status 2.2.2. DDR5 x32 + user bits through NoC is not supported 2.2.3. PhyMux EMIF lockstep pinout configurations Restrictions 2.2.4. DDR4/DDR5 x8 is not supported 2.2.5. GPIO-B blocked in mixed GPIO-B/EMIF use cases 2.2.6. DDR4 rDBI is not working 2.2.7. LPDDR5 and DDR5 reduced sequential write/read bandwidth when using Fabric Sync Fabric direct mode in x16 2-channel configuration 2.2.8. LPDDR5 and DDR5 maximum bandwidth for sequential short write is limited 2.2.9. LPDDR5 and DDR5 controller does not support non-aligned transactions
2.3. Configuration and Security x
2.3.1. AS Fast mode BootROM delay
2.4. Fabric NoC x
2.4.1. Lower than expected performance with Fabric NoC-enabled design
2.5. Device Power Supply, Core, I/O x
2.5.1. I/O PLL reference clock frequency and duty cycle specification update
3. Arm* Cortex*-A53 MPCore and CoreSight* Errata x
3.1. 843819: Memory Locations May be Accessed Speculatively Due to Instruction Fetches When HCR.VM is Set 3.2. 845719: A Load May Read Incorrect Data 3.3. 855871: ETM Does Not Report IDLE State When Disabled Using OSLOCK 3.4. 855872: A Store-Exclusive Instruction Might Pass When it Should Fail 3.5. 711668: Configuration Extension Register Has Wrong Value Status 3.6. 720107: Periodic Synchronization Can Be Delayed and Cause Overflow 3.7. 855873: An Eviction Might Overtake a Cache Clean Operation 3.8. 853172: ETM May Assert AFREADY Before All Data Has Been Output 3.9. 836870: Non-Allocating Reads May Prevent a Store Exclusive From Passing 3.10. 836919: Write of the JMCR in EL0 Does Not Generate an UNDEFINED Exception 3.11. 845819: Instruction Sequences Containing AES Instructions May Produce Incorrect Results 3.12. 851672: ETM May Trace an Incorrect Exception Address 3.13. 851871: ETM May Lose Counter Events While Entering WFx Mode 3.14. 852071: Direct Branch Instructions Executed Before a Trace Flush May be Output in an Atom Packet After Flush Acknowledgment 3.15. 852521: A64 Unconditional Branch May Jump to Incorrect Address 3.16. 855827: PMU Counter Values May Be Inaccurate When Monitoring Certain Events 3.17. 855829: Reads of PMEVCNTR<n> are not Masked by HDCR.HPMN 3.18. 855830: Loads of Mismatched Size May not be Single-Copy Atomic
4. Agilex™ 7 M-Series User Guidelines x
4.1. Power Estimation Guardband
1. About This Document
2. Known Issue List for Devices
3. Arm* Cortex*-A53 MPCore and CoreSight* Errata
4. Agilex™ 7 M-Series User Guidelines
5. Document Revision History for the Agilex™ 7 M-Series Known Issue List

2.2.1. DDR5 RDIMM support

Description

When configuring an External Memory Interface as DDR5 RDIMM, you must ensure that the DIMM's speed specification matches the operating data rate of the DDR5 interface. Using an RDIMM specified for a higher data rate with a lower operating data rate is not allowed.

Workaround

If you are operating DDR5 RDIMM interface at 4800 Mbps, you must use DDR5 RDIMM with 4800 Mbps specification.

Status

Table 27.  Device Status Table
Devices Affected Planned Fix
  • AGMx0xxR47Axxxx
  • AGMx0xxR31Bxxxx
None
Level Two Title