MIPI D-PHY IP User Guide: Agilex™ 5 FPGAs

Download PDF
ID 817561
Date 7/08/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the Agilex™ 5 FPGA MIPI D-PHY IP 2. Introduction 3. Agilex™ 5 MIPI D-PHY Architecture 4. MIPI D-PHY Interface Design Guidelines 5. Configuring and Generating the MIPI D-PHY IP 6. Interface Signals and Register Maps 7. Document Revision History for Agilex™ 5 FPGA MIPI D-PHY IP User Guide
1. About the Agilex™ 5 FPGA MIPI D-PHY IP x
1.1. Release Information
2. Introduction x
2.1. Supported Data Lanes and Clock Lane Per Single HSIO Bank 2.2. Unsupported Features
3. Agilex™ 5 MIPI D-PHY Architecture x
3.1. Agilex™ 5 MIPI D-PHY TX 3.2. Agilex™ 5 MIPI D-PHY RX 3.3. Initialization and Reset Sequences 3.4. Calibration 3.5. CSR Clock Domain Crossing (CDC)
4. MIPI D-PHY Interface Design Guidelines x
4.1. Identifying Pin Assignments Based on Byte Location 4.2. Assigning the RZQ pin and Dedicated Reference Clock Pin for MIPI D-PHY IP 4.3. Supported I/O Features in MIPI D-PHY I/O Standard 4.4. Using the Remaining I/O Pin from Same Byte Location 4.5. I/O Bank Sharing 4.6. MIPI D-PHY Placement Rules 4.7. MIPI Interface Layout Design Guidelines 4.8. Handling MIPI D-PHY IP Reset
5. Configuring and Generating the MIPI D-PHY IP x
5.1. Creating a MIPI D-PHY Project 5.2. Configuring the D-PHY IP Tab 5.3. Configuring the MIPI D-PHY RX Mode 5.4. Configuring the MIPI D-PHY TX Mode 5.5. Generating the Design Example
5.5. Generating the Design Example x
5.5.1. Generating the Synthesizable MIPI D-PHY Design Example 5.5.2. Generating MIPI D-PHY IP Design Example with External Loopback Enabled for Simulation
5.5.1. Generating the Synthesizable MIPI D-PHY Design Example x
5.5.1.1. Design Example Block Diagram 5.5.1.2. External Interfaces
5.5.2. Generating MIPI D-PHY IP Design Example with External Loopback Enabled for Simulation x
5.5.2.1. Simulation Design Example with External Loopback Enabled Block Diagram 5.5.2.2. Simulating MIPI D-PHY IP Design Example with Modelsim* and Questasim* 5.5.2.3. Simulating MIPI D-PHY IP Design Example with Synopsys VCSMX* and Xcelium*
6. Interface Signals and Register Maps x
6.1. Interface Signals 6.2. Register Maps
6.1. Interface Signals x
6.1.1. General Interface Signals 6.1.2. AXI-Lite Interface 6.1.3. Core Register Bus 6.1.4. D-PHY RX PPI Interface Signals 6.1.5. D-PHY TX PPI Interface Signals 6.1.6. AXI-Lite CSR Access
6.2. Register Maps x
6.2.1. D-PHY IP Registers 6.2.2. D-PHY Traffic Generator (TG) Registers
6.2.1. D-PHY IP Registers x
6.2.1.1. IP_ID 6.2.1.2. IP_CAP 6.2.1.3. D0_CAP 6.2.1.4. DN_CAP 6.2.1.5. RX_CAP 6.2.1.6. TX_CAP 6.2.1.7. TX_PREAMBLE_LEN 6.2.1.8. D-PHY_CSR 6.2.1.9. TX_CLK_LANE_PS 6.2.1.10. RX_DLANE_ERR 6.2.1.11. SKEW_CAL_LEN_B0 6.2.1.12. SKEW_CAL_LEN_B1 6.2.1.13. SKEW_CAL_LEN_B2 6.2.1.14. SKEW_CAL_LEN_B3 6.2.1.15. ALT_CAL_LEN_B0 6.2.1.16. ALT_CAL_LEN_B1 6.2.1.17. ALT_CAL_LEN_B2 6.2.1.18. ALT_CAL_LEN_B3 6.2.1.19. CLK_CSR 6.2.1.20. CLK_STATUS 6.2.1.21. DLANE_CSR_0 6.2.1.22. DLANE_STATUS_0 6.2.1.23. RX_DLANE_DESKEW_DELAY_0 6.2.1.24. RX_DLANE_ERR_0 6.2.1.25. DLANE_CSR_1 6.2.1.26. DLANE_STATUS_1 6.2.1.27. RX_DLANE_DESKEW_DELAY_1 6.2.1.28. RX_DLANE_ERR_1 6.2.1.29. DLANE_CSR_2 6.2.1.30. DLANE_STATUS_2 6.2.1.31. RX_DLANE_DESKEW_DELAY_2 6.2.1.32. RX_DLANE_ERR_2 6.2.1.33. DLANE_CSR_3 6.2.1.34. DLANE_STATUS_3 6.2.1.35. RX_DLANE_DESKEW_DELAY_3 6.2.1.36. RX_DLANE_ERR_3 6.2.1.37. DLANE_CSR_4 6.2.1.38. DLANE_STATUS_4 6.2.1.39. RX_DLANE_DESKEW_DELAY_4 6.2.1.40. RX_DLANE_ERR_4 6.2.1.41. DLANE_CSR_5 6.2.1.42. DLANE_STATUS_5 6.2.1.43. RX_DLANE_DESKEW_DELAY_5 6.2.1.44. RX_DLANE_ERR_5 6.2.1.45. DLANE_CSR_6 6.2.1.46. DLANE_STATUS_6 6.2.1.47. RX_DLANE_DESKEW_DELAY_6 6.2.1.48. RX_DLANE_ERR_6 6.2.1.49. DLANE_CSR_7 6.2.1.50. DLANE_STATUS_7 6.2.1.51. RX_DLANE_DESKEW_DELAY_7 6.2.1.52. RX_DLANE_ERR_7 6.2.1.53. TX_LPX 6.2.1.54. TX_HS_EXIT 6.2.1.55. TX_LP_EXIT 6.2.1.56. TX_CLK_PREPARE 6.2.1.57. TX_CLK_ZERO 6.2.1.58. TX_CLK_POST 6.2.1.59. TX_CLK_PRE 6.2.1.60. TX_HS_PREPARE 6.2.1.61. TX_HS_ZERO 6.2.1.62. TX_HS_TRAIL 6.2.1.63. TX_INIT 6.2.1.64. TX_WAKE 6.2.1.65. RX_CLK_LOSS_DETECT 6.2.1.66. RX_CLK_SETTLE 6.2.1.67. RX_HS_SETTLE 6.2.1.68. RX_INIT 6.2.1.69. RX_CLK_POST 6.2.1.70. RX_CAL_REG_CTRL 6.2.1.71. RX_CAL_STATUS_D-PHY 6.2.1.72. RX_CAL_SKEW_W_START_MUX 6.2.1.73. RX_CAL_SKEW_W_END_MUX 6.2.1.74. RX_CAL_ALT_W_START_MUX 6.2.1.75. RX__CAL_ALT_W_END_MUX 6.2.1.76. RX_DESKEW_DELAY_MUX 6.2.1.77. RX_CAL_STATUS_LANE_MUX 6.2.1.78. PRBS_INIT_0 6.2.1.79. PRBS_INIT_1 6.2.1.80. PRBS_INIT_2 6.2.1.81. PRBS_INIT_3 6.2.1.82. PRBS_INIT_4 6.2.1.83. PRBS_INIT_5 6.2.1.84. PRBS_INIT_6 6.2.1.85. TX_TM_CONTROL 6.2.1.86. TX_MNL_IO_0 6.2.1.87. TX_MNL_D_LP_EN 6.2.1.88. RX_TM_CONTROL
6.2.2. D-PHY Traffic Generator (TG) Registers x
6.2.2.1. TG_TOP_CTRL_0 6.2.2.2. TG_TOP_CTRL_1 6.2.2.3. TG_TOP_DONE 6.2.2.4. TG_TOP_FAIL 6.2.2.5. TG_TOP_TEST_EN 6.2.2.6. TG_TOP_TEST_LINK 6.2.2.7. TARGET_TEST_CNT 6.2.2.8. TCHK_CONTROL 6.2.2.9. TCHK_LINK_STATUS 6.2.2.10. HS_DONE_LANES 6.2.2.11. TCHK_LINK_ERR_STATUS 6.2.2.12. LANE_ERROR_SOT_LANES 6.2.2.13. CAL_ERROR_LANES 6.2.2.14. HS_ERR_LANES 6.2.2.15. HS_TEST_CNT 6.2.2.16. LPDT_TEST_CNT 6.2.2.17. TRIGGER_TEST_CNT 6.2.2.18. ULPS_TEST_CNT 6.2.2.19. TG_RX_OVRD_DATA_PAT 6.2.2.20. TG_RX_BIT_ERROR_CNT 6.2.2.21. TG_RX_HS_TXFER_CNT 6.2.2.22. TG_LINK_CONTROL 6.2.2.23. TG_INIT_CNT 6.2.2.24. TG_HS_LEN 6.2.2.25. TG_LP_LEN 6.2.2.26. TG_SKEW_CAL 6.2.2.27. TG_ALT_CAL 6.2.2.28. TG_PER_SKEW_CAL_LEN 6.2.2.29. TG_TEST_CNT 6.2.2.30. TG_OVRD_DATA_PAT 6.2.2.31. TG_TX_HS_TXFER_CNT
1. About the Agilex™ 5 FPGA MIPI D-PHY IP
2. Introduction
3. Agilex™ 5 MIPI D-PHY Architecture
4. MIPI D-PHY Interface Design Guidelines
5. Configuring and Generating the MIPI D-PHY IP
6. Interface Signals and Register Maps
7. Document Revision History for Agilex™ 5 FPGA MIPI D-PHY IP User Guide

5.5.1.1. Design Example Block Diagram

The MIPI DPHY synthesis design example contains the major blocks shown in the figure below.

Pattern checker: The traffic generator pattern checker monitors D-PHY RX PPI bus activities and compares with the expected behavior. The expected activities mirror the pattern generator’s activity including the expected data and number of iterations.

The pattern generator generates both fail and done signals. The fail signal is asserted immediately after an error condition is detected and stays asserted until the test is restarted. The done signal is asserted when all the enabled tests have reached the expected number of iterations.

Pattern generator: The role of the pattern generator is to create PPI traffic, both HS and LP.

D-PHY IP: The D-PHY IP provides the physical layer implementation of the MIPI D-PHY interface. The PHY converts the parallel PPI bus to/from the serial MIPI D-PHY interface.

Figure 18. Design Example Top-Level Diagram for Synthesis
Level Two Title