Visible to Intel only — GUID: mwh1409958298944
Ixiasoft
1. About the F-Tile Triple-Speed Ethernet Intel® FPGA IP User Guide
2. About F-Tile Triple-Speed Ethernet Intel® FPGA IP
3. Getting Started
4. Parameter Settings
5. Functional Description
6. Configuration Register Space
7. Interface Signals
8. Design Considerations
9. Timing Constraints
10. Software Programming Interface
11. F-Tile Triple-Speed Ethernet Intel® FPGA IP User Guide Archives
12. Document Revision History for the F-Tile Triple-Speed Ethernet Intel® FPGA IP User Guide
A. Ethernet Frame Format
B. Simulation Parameters
5.1.1. MAC Architecture
5.1.2. MAC Interfaces
5.1.3. MAC Transmit Datapath
5.1.4. MAC Receive Datapath
5.1.5. MAC Transmit and Receive Latencies
5.1.6. FIFO Buffer Thresholds
5.1.7. Congestion and Flow Control
5.1.8. Magic Packets
5.1.9. MAC Local Loopback
5.1.10. MAC Reset
5.1.11. PHY Management (MDIO)
5.1.12. Connecting MAC to External PHYs
6.1.1. Base Configuration Registers (Dword Offset 0x00 – 0x17)
6.1.2. Statistics Counters (Dword Offset 0x18 – 0x38)
6.1.3. Transmit and Receive Command Registers (Dword Offset 0x3A – 0x3B)
6.1.4. Supplementary Address (Dword Offset 0xC0 – 0xC7)
6.1.5. IEEE 1588v2 Feature (Dword Offset 0xD0 – 0xD6)
6.1.6. Deterministic Latency (Dword Offset 0xE1– 0xE3)
6.1.7. IEEE 1588v2 Feature PMA Delay
7.1.1. 10/100/1000 Ethernet MAC Signals
7.1.2. 10/100/1000 Multiport Ethernet MAC Signals
7.1.3. 10/100/1000 Ethernet MAC with 1000BASE-X/SGMII PCS Signals
7.1.4. 10/100/1000 Ethernet MAC with 1000BASE-X/SGMII 2XTBI PCS and Embedded PMA Signals (F-Tile)
7.1.5. 10/100/1000 Ethernet MAC Without Internal FIFO Buffers with 1000BASE-X/SGMII 2XTBI PCS Signals
7.1.6. 10/100/1000 Ethernet MAC Without Internal FIFO Buffers with IEEE 1588v2 , 1000BASE-X/SGMII 2XTBI PCS, and Embedded Serial PMA Signals
7.1.7. 10/100/1000 Multiport Ethernet MAC with 1000BASE-X/SGMII PCS Signals
7.1.8. 10/100/1000 Ethernet MAC with 1000BASE-X/SGMII PCS and Embedded PMA Signals
7.1.9. 10/100/1000 Multiport Ethernet MAC with 1000BASE-X/SGMII PCS and Embedded PMA Signals
7.1.10. 1000BASE-X/SGMII PCS Signals
7.1.11. 1000BASE-X/SGMII 2XTBI PCS Signals
7.1.12. 1000BASE-X/SGMII PCS and PMA Signals
7.1.1.1. Clock and Reset Signals
7.1.1.2. Clock Enabler Signals
7.1.1.3. MAC Control Interface Signals
7.1.1.4. MAC Status Signals
7.1.1.5. MAC Receive Interface Signals
7.1.1.6. MAC Transmit Interface Signals
7.1.1.7. Pause and Magic Packet Signals
7.1.1.8. MII/GMII/RGMII Signals
7.1.1.9. PHY Management Signals
7.1.1.10. ECC Status Signals
7.1.6.1. Deterministic Latency Clock Signals
7.1.6.2. IEEE 1588v2 RX Timestamp Signals
7.1.6.3. IEEE 1588v2 TX Timestamp Signals
7.1.6.4. IEEE 1588v2 TX Timestamp Request Signals
7.1.6.5. IEEE 1588v2 TX Insert Control Timestamp Signals
7.1.6.6. IEEE 1588v2 Time-of-Day (TOD) Clock Interface Signals
7.1.6.7. IEEE 1588v2 PCS Phase Measurement Clock Signal
10.6.1. alt_tse_mac_get_common_speed()
10.6.2. alt_tse_mac_set_common_speed()
10.6.3. alt_tse_phy_add_profile()
10.6.4. alt_tse_system_add_sys()
10.6.5. triple_speed_ethernet_init()
10.6.6. tse_mac_close()
10.6.7. tse_mac_raw_send()
10.6.8. tse_mac_setGMII mode()
10.6.9. tse_mac_setMIImode()
10.6.10. tse_mac_SwReset()
Visible to Intel only — GUID: mwh1409958298944
Ixiasoft
3.5. Simulating Intel® FPGA IP Cores
The Quartus® Prime software supports IP core RTL simulation in specific EDA simulators. IP generation optionally creates simulation files, including the functional simulation model, any testbench (or example design), and vendor-specific simulator setup scripts for each IP core. You can use the functional simulation model and any testbench or example design for simulation. IP generation output may also include scripts to compile and run any testbench. The scripts list all models or libraries you require to simulate your IP core.
The Quartus® Prime software provides integration with many simulators and supports multiple simulation flows, including your own scripted and custom simulation flows. Whichever flow you choose, IP core simulation involves the following steps:
- Generate IP HDL, testbench (or example design), and simulator setup script files.
- Set up your simulator environment and any simulation scripts.
- Compile simulation model libraries.
- Run your simulator.