Visible to Intel only — GUID: haj1555628414839
Ixiasoft
1. Stratix® 10 Configuration User Guide
2. Stratix® 10 Configuration Details
3. Stratix® 10 Configuration Schemes
4. Including the Reset Release Intel® FPGA IP in Your Design
5. Remote System Update (RSU)
6. Stratix® 10 Configuration Features
7. Stratix® 10 Debugging Guide
8. Stratix® 10 Configuration User Guide Archives
9. Document Revision History for the Stratix® 10 Configuration User Guide
2.1. Stratix® 10 Configuration Timing Diagram
2.2. Configuration Flow Diagram
2.3. Device Response to Configuration and Reset Events
2.4. Additional Clock Requirements for HPS, PCIe* , eSRAM, and HBM2
2.5. Stratix® 10 Configuration Pins
2.6. Configuration Clocks
2.7. Maximum Configuration Time Estimation
2.8. Generating Compressed .sof File
2.9. Dual-die Configuration on Stratix® 10 GX 10M
3.1.1. Avalon® -ST Configuration Scheme Hardware Components and File Types
3.1.2. Enabling Avalon-ST Device Configuration
3.1.3. The AVST_READY Signal
3.1.4. RBF Configuration File Format
3.1.5. Avalon-ST Single-Device Configuration
3.1.6. Debugging Guidelines for the Avalon® -ST Configuration Scheme
3.1.7. IP for Use with the Avalon® -ST Configuration Scheme: Parallel Flash Loader II Intel® FPGA IP (PFL II)
3.1.7.1. Functional Description
3.1.7.2. Designing with the Parallel Flash Loader II Intel® FPGA IP for Avalon-ST Single Device Configuration
3.1.7.3. Generating the Parallel Flash Loader II Intel® FPGA IP
3.1.7.4. Constraining the Parallel Flash Loader II Intel® FPGA IP
3.1.7.5. Using the Parallel Flash Loader II Intel® FPGA IP
3.1.7.6. Supported Flash Memory Devices
3.1.7.3.1. Controlling Avalon-ST Configuration with Parallel Flash Loader II Intel® FPGA IP
3.1.7.3.2. Mapping Parallel Flash Loader II Intel® FPGA IP and Flash Address
3.1.7.3.3. Creating a Single Parallel Flash Loader II Intel® FPGA IP for Programming and Configuration
3.1.7.3.4. Creating Separate Parallel Flash Loader II Intel® FPGA IP Functions
3.1.7.4.1. Parallel Flash Loader II Intel® FPGA IP Recommended Design Constraints to FPGA Avalon-ST Pins
3.1.7.4.2. Parallel Flash Loader II Intel® FPGA IP Recommended Design Constraints for Using QSPI Flash
3.1.7.4.3. Parallel Flash Loader II Intel® FPGA IP Recommended Design Constraints for using CFI Flash
3.1.7.4.4. Parallel Flash Loader II Intel® FPGA IP Recommended Constraints for Other Input Pins
3.1.7.4.5. Parallel Flash Loader II Intel® FPGA IP Recommended Constraints for Other Output Pins
3.2.1. AS Configuration Scheme Hardware Components and File Types
3.2.2. AS Single-Device Configuration
3.2.3. AS Using Multiple Serial Flash Devices
3.2.4. AS Configuration Timing Parameters
3.2.5. Skew Tolerance Guidelines
3.2.6. Programming Serial Flash Devices
3.2.7. Serial Flash Memory Layout
3.2.8. AS_CLK
3.2.9. Active Serial Configuration Software Settings
3.2.10. Quartus® Prime Programming Steps
3.2.11. Debugging Guidelines for the AS Configuration Scheme
5.1. Remote System Update Functional Description
5.2. Guidelines for Performing Remote System Update Functions for Non-HPS
5.3. Commands and Responses
5.4. Quad SPI Flash Layout
5.5. Generating Remote System Update Image Files Using the Programming File Generator
5.6. Remote System Update from FPGA Core Example
5.7. Debugging Guidelines for RSU Configuration
5.6.1. Prerequisites
5.6.2. Creating Initial Flash Image Containing Bitstreams for Factory Image and One Application Image
5.6.3. Programming Flash Memory with the Initial Remote System Update Image
5.6.4. Reconfiguring the Device with an Application or Factory Image
5.6.5. Adding an Application Image
5.6.6. Removing an Application Image
7.1. Configuration Debugging Checklist
7.2. Stratix® 10 Configuration Architecture Overview
7.3. Understanding Configuration Status Using quartus_pgm command
7.4. SDM Debug Toolkit Overview
7.5. Configuration Pin Differences from Previous Device Families
7.6. Configuration File Format Differences
7.7. Understanding SEUs
7.8. Reading the Unique 64-Bit CHIP ID
7.9. E-Tile Transceivers May Fail To Configure
7.10. Understanding and Troubleshooting Configuration Pin Behavior
7.11. Configuration Debugger Tool
Visible to Intel only — GUID: haj1555628414839
Ixiasoft
4.5.1. Device Initialization
The following steps summarize device initialization:
- An external host drives a configuration request to the Secure Device Manager (SDM) by driving nCONFIG high. The SDM exits the IDLE state and signals the beginning of configuration by driving nSTATUS high and driving configuration data.
- The SDM asserts CONF_DONE indicating that the Intel FPGA has successfully received all the configuration data.
- The SDM uses the configuration logic to start non-gated clocks in the fabric. Hyperflex® registers begin shifting data. Consequently, the initial conditions of Hyperflex® registers can be random. Use the Disable Register Power-up Initialization setting in the Quartus® Prime Configuration dialog box to disable Hyperflex® register initialization during power-on as explained below.
- The SDM uses the configuration logic to enable and initialize user registers in the LABs, DSP, and embedded memory blocks.
- The SDM drives INIT_DONE to indicate that the device has fully entered user mode. The Reset Release IP asserts nINIT_DONE. Intel recommends that you use nINIT_DONE to gate your reset logic.
- The FPGA is now in user mode and ready for operation.