Stratix® 10 Configuration via Protocol (CvP) Implementation User Guide

Download PDF
ID 683704
Date 10/02/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. CvP Description 3. CvP Topologies 4. Design Considerations 5. CvP Driver and Registers 6. Understanding the Design Steps for CvP Initialization and Update Mode in Stratix® 10 7. Stratix® 10 Configuration via Protocol (CvP) Implementation User Guide Archives 8. Document Revision History
1. Overview x
1.1. Benefits of Using CvP 1.2. CvP System 1.3. CvP Modes
1.3. CvP Modes x
1.3.1. CvP Limitations and Restrictions
1.3.1. CvP Limitations and Restrictions x
1.3.1.1. CvP Error Recovery
2. CvP Description x
2.1. Configuration Images 2.2. CvP Modes 2.3. Compression Features 2.4. Pin Description
2.2. CvP Modes x
2.2.1. CvP Initialization Mode 2.2.2. CvP Update Mode
3. CvP Topologies x
3.1. Single Endpoint 3.2. Multiple Endpoints
4. Design Considerations x
4.1. Designing CvP for an Open System 4.2. Designing CvP for a Closed System
4.1. Designing CvP for an Open System x
4.1.1. FPGA Power Supplies Ramp Time Requirement 4.1.2. PCIe* Wake-Up Time Requirement
4.1.2. PCIe* Wake-Up Time Requirement x
4.1.2.1. For CvP Initialization Mode 4.1.2.2. For CvP Update Mode
5. CvP Driver and Registers x
5.1. CvP Driver Support 5.2. CvP Driver Flow 5.3. VSEC Registers for CvP
5.3. VSEC Registers for CvP x
5.3.1. Vendor Specific Capability Header Register 5.3.2. Vendor Specific Header Register 5.3.3. Intel Marker Register 5.3.4. User Configurable Device/Board ID Register 5.3.5. CvP Status Register 5.3.6. CvP Mode Control Register 5.3.7. CvP Data Registers 5.3.8. CvP Programming Control Register 5.3.9. CvP Credit Register
6. Understanding the Design Steps for CvP Initialization and Update Mode in Stratix® 10 x
6.1. Implementation of CvP Initialization Mode 6.2. Implementation of CvP Update Mode
6.1. Implementation of CvP Initialization Mode x
6.1.1. Generating the Synthesis HDL files for Avalon® Streaming Stratix® 10 Hard IP for PCI Express 6.1.2. Setting up the CvP Parameters in Device and Pin Options 6.1.3. Compiling the Design 6.1.4. Converting the SOF File 6.1.5. Bringing up the Hardware
6.1.5. Bringing up the Hardware x
6.1.5.1. Installing the Upstream Open Source CvP Driver in Linux Systems 6.1.5.2. Modifying MSEL/DIP switch on Stratix® 10 FPGA Development Kit 6.1.5.3. Programming CvP Images
6.2. Implementation of CvP Update Mode x
6.2.1. Instantiating the PCIe* Hard IP 6.2.2. Setting Up the CvP Parameters 6.2.3. Setting up the Base Revision 6.2.4. Setting up and Compile the Updated Revision 6.2.5. Converting the SOF file of the Updated Revision 6.2.6. Programming the Core RBF file from the Updated Revision via PCIe Link
6.2.3. Setting up the Base Revision x
6.2.3.1. Creating a Reserved Core Partition 6.2.3.2. Defining a Logic Lock Region 6.2.3.3. Compiling and Exporting the Root Partition
1. Overview
2. CvP Description
3. CvP Topologies
4. Design Considerations
5. CvP Driver and Registers
6. Understanding the Design Steps for CvP Initialization and Update Mode in Stratix® 10
7. Stratix® 10 Configuration via Protocol (CvP) Implementation User Guide Archives
8. Document Revision History

2.2.1. CvP Initialization Mode

In this mode, an external configuration device stores the periphery image and it loads into the FPGA through the Active Serial x4 (Fast mode) configuration scheme. The host memory stores the core image and it loads into the FPGA through the PCIe* link. The PCIe* REFCLK needs to be running prior to sending the periphery image.

After the periphery image configuration is complete, the CONF_DONE signal goes high and the FPGA starts PCIe* link training. When PCIe* link training is complete, the PCIe* link transitions to L0 state and then allows the host to complete PCIe* enumeration of the link. The PCIe* host then initiates the core image configuration through the PCIe* link.

After the core image configuration is complete, the CvP_CONFDONE pin (if enabled) goes high, indicating the FPGA is fully configured.

After the FPGA is fully configured, the FPGA enters user mode. If the INIT_DONE signal is enabled, the INIT_DONE signal goes high after initialization is complete and the FPGA enters the user mode.

In user mode, the PCIe* links are available for normal PCIe* applications.

Level Two Title