Viterbi IP Core User Guide

Download PDF
ID 683280
Date 11/06/2017
Public
Document Table of Contents
Document Table of Contents x
1. About the Viterbi IP Core 2. Viterbi IP Core Getting Started 3. Viterbi IP Core Functional Description A. Viterbi IP Core User Guide Document Archives 4. Document Revision History
1. About the Viterbi IP Core x
1.1. Intel® DSP IP Core Features 1.2. Viterbi IP Core Features 1.3. DSP IP Core Device Family Support 1.4. DSP IP Core Verification 1.5. Viterbi IP Core Release Information 1.6. Viterbi IP Core Performance and Resource Utilization
2. Viterbi IP Core Getting Started x
2.1. Installing and Licensing Intel® FPGA IP Cores 2.2. IP Catalog and Parameter Editor 2.3. Generating IP Cores ( Intel® Quartus® Prime Pro Edition) 2.4. Simulating Intel® FPGA IP Cores 2.5. DSP Builder for Intel® FPGAs Design Flow
2.1. Installing and Licensing Intel® FPGA IP Cores x
2.1.1. Intel® FPGA IP Evaluation Mode 2.1.2. Viterbi IP Core Intel® FPGA IP Evaluation Mode Timeout Behavior
2.3. Generating IP Cores ( Intel® Quartus® Prime Pro Edition) x
2.3.1. IP Core Generation Output ( Intel® Quartus® Prime Pro Edition)
3. Viterbi IP Core Functional Description x
3.1. Decoder 3.2. Convolutional Encoder 3.3. Trellis Coded Modulation 3.4. Viterbi IP Core Parameters 3.5. Viterbi IP Core Interfaces and Signals
3.3. Trellis Coded Modulation x
3.3.1. Half-Rate Convolutional Codes 3.3.2. Trellis Decoder 3.3.3. About Converting Received Signals 3.3.4. Trellis Termination 3.3.5. Trellis Initialization
3.4. Viterbi IP Core Parameters x
3.4.1. Architecture 3.4.2. Code Sets 3.4.3. Viterbi Parameters 3.4.4. Test Data
3.4.1. Architecture x
3.4.1.1. BER Estimator 3.4.1.2. Node Synchronization
3.4.3. Viterbi Parameters x
3.4.3.1. Soft Symbol Input 3.4.3.2. State Metrics 3.4.3.3. Throughput Calculator 3.4.3.4. Latency Calculator
3.4.4. Test Data x
3.4.4.1. External Puncturing
3.5. Viterbi IP Core Interfaces and Signals x
3.5.1. Avalon-ST Interfaces in DSP IP Cores 3.5.2. Global Signals 3.5.3. Avalon-ST Sink Signals 3.5.4. Avalon Source-ST Signals 3.5.5. Configuration Signals 3.5.6. Status Signals 3.5.7. Viterbi IP Core Timing Diagrams
1. About the Viterbi IP Core
2. Viterbi IP Core Getting Started
3. Viterbi IP Core Functional Description
A. Viterbi IP Core User Guide Document Archives
4. Document Revision History

3.5.6. Status Signals

Signal Description
bestadd[(L-1):1] The best address state. The address corresponding to the best metric as it is being found by the best state finder. The metric of this state if shown in bestmet. If you select Continuous or None optimization and turn off best state finder, the IP core leaves this signal open. For parallel decoders, the IP core removes this signal.
bestmet[bmgwide:1] The best metric. The bestmet signal shows the best state metric for every trellis step as the best state finder finds it. The state that contains this best metric is shown in bestadd. If you select Continuous or None for optimization and turn off best state finder, the IP core leave this signal open, For parallel decoders, the IP core removes this signal.
normalizations[8:1] The normalizations bus indicates in real time the number of normalizations that occur since you activated sink_sop.
numerr[] The numerr bus contains the number of errors detected during a block. The iP core updates it each time it detects an error, so you can see the location of individual errors. It is reset when source_sop asserted; it is valid two-clock cycles after source_sop. The wizard automatically sets the width of this bus. If you do not select a BER block, the IP cores leaves this signal open. Only available when you select the BER estimator option
Level Two Title