Agilex™ 7 Embedded Memory User Guide

Download PDF
ID 683241
Date 10/21/2024
Public
Document Table of Contents
Document Table of Contents x
1. Agilex™ 7 Embedded Memory Overview 2. Agilex™ 7 Embedded Memory Architecture and Features 3. Agilex™ 7 Embedded Memory Design Considerations 4. Agilex™ 7 Embedded Memory IP References 5. Agilex™ 7 Embedded Memory Debugging 6. Agilex™ 7 Embedded Memory User Guide Archives 7. Document Revision History for the Agilex™ 7 Embedded Memory User Guide
1. Agilex™ 7 Embedded Memory Overview x
1.1. Agilex™ 7 Embedded Memory Features
2. Agilex™ 7 Embedded Memory Architecture and Features x
2.1. Fabric Network-On-Chip (NoC) in Agilex™ 7 M-Series M20K Blocks 2.2. Byte Enable in Agilex™ 7 Embedded Memory Blocks 2.3. Address Clock Enable Support 2.4. Asynchronous Clear and Synchronous Clear 2.5. Memory Blocks Error Correction Code (ECC) Support 2.6. Agilex™ 7 Embedded Memory Clocking Modes 2.7. Agilex™ 7 Embedded Memory Configurations 2.8. Force-to-Zero 2.9. Coherent Read Memory 2.10. Freeze Logic 2.11. True Dual Port Dual Clock Emulator 2.12. Initial Value of Read and Write Address Registers 2.13. Timing/Power Optimization Feature in M20K Blocks 2.14. Agilex™ 7 Supported Embedded Memory IPs
2.2. Byte Enable in Agilex™ 7 Embedded Memory Blocks x
2.2.1. Byte Enable Controls 2.2.2. Data Byte Output 2.2.3. Byte Enable Behavior
2.5. Memory Blocks Error Correction Code (ECC) Support x
2.5.1. Error Correction Code Truth Table 2.5.2. Parity Bit 2.5.3. ECC Parity Flip 2.5.4. ECC Read-During-Write Behavior
2.6. Agilex™ 7 Embedded Memory Clocking Modes x
2.6.1. Single Clock Mode 2.6.2. Read/Write Clock Mode 2.6.3. Input/Output Clock Mode 2.6.4. Asynchronous/Synchronous Clears in Clocking Modes 2.6.5. Output Read Data in Simultaneous Read/Write 2.6.6. Independent Clock Enables in Clocking Modes
2.7. Agilex™ 7 Embedded Memory Configurations x
2.7.1. Mixed-Width Port Configurations
2.9. Coherent Read Memory x
2.9.1. Forwarding Logic
3. Agilex™ 7 Embedded Memory Design Considerations x
3.1. Consider the Memory Block Selection 3.2. Consider the Concurrent Read Behavior 3.3. Read-During-Write (RDW) 3.4. Consider Power-Up State and Memory Initialization 3.5. Reduce Power Consumption 3.6. Avoid Providing Non-Deterministic Input 3.7. Avoid Changing Clock Signals and Other Control Signals Simultaneously 3.8. Advanced Settings in Quartus® Prime Software for Memory 3.9. Consider the Memory Depth Setting 3.10. M20K Embedded Memory Block Input Clock Quality Requirement 3.11. Consider Registering the Memory Output
3.3. Read-During-Write (RDW) x
3.3.1. Customize Read-During-Write Behavior
3.3.1. Customize Read-During-Write Behavior x
3.3.1.1. Same-Port Read-During-Write Mode 3.3.1.2. Mixed-Port Read-During-Write Mode
4. Agilex™ 7 Embedded Memory IP References x
4.1. On Chip Memory RAM and ROM Intel® FPGA IP Cores 4.2. eSRAM Agilex™ FPGA IP 4.3. FIFO Intel® FPGA IP 4.4. Shift Register (RAM-based) Intel® FPGA IP
4.1. On Chip Memory RAM and ROM Intel® FPGA IP Cores x
4.1.1. Release Information for RAM and ROM Intel® FPGA IPs 4.1.2. RAM: 1-PORT Intel® FPGA IP Parameters 4.1.3. RAM: 2-PORT Intel® FPGA IP Parameters 4.1.4. RAM: 4-PORT Intel® FPGA IP Parameters 4.1.5. ROM: 1-PORT Intel® FPGA IP Parameters 4.1.6. ROM: 2-PORT Intel® FPGA IP Parameters 4.1.7. Changing Parameter Settings Manually 4.1.8. RAM and ROM Interface Signals
4.1.7. Changing Parameter Settings Manually x
4.1.7.1. RAM and ROM Parameter Settings
4.2. eSRAM Agilex™ FPGA IP x
4.2.1. Release Information for eSRAM Agilex™ FPGA IP 4.2.2. eSRAM System Features 4.2.3. eSRAM Agilex™ FPGA IP Parameters 4.2.4. eSRAM Agilex™ FPGA IP Interface Signals 4.2.5. eSRAM Timing Diagrams
4.2.2. eSRAM System Features x
4.2.2.1. eSRAM Specifications
4.3. FIFO Intel® FPGA IP x
4.3.1. Release Information for FIFO Intel® FPGA IP 4.3.2. Configuration Methods 4.3.3. Specifications 4.3.4. FIFO Functional Timing Requirements 4.3.5. SCFIFO ALMOST_EMPTY Functional Timing 4.3.6. FIFO Output Status Flag and Latency 4.3.7. FIFO Metastability Protection and Related Options 4.3.8. FIFO Synchronous Clear and Asynchronous Clear Effect 4.3.9. SCFIFO and DCFIFO Show-Ahead Mode 4.3.10. Different Input and Output Width 4.3.11. DCFIFO Timing Constraint Setting 4.3.12. Coding Example for Manual Instantiation 4.3.13. Design Example 4.3.14. Gray-Code Counter Transfer at the Clock Domain Crossing 4.3.15. Guidelines for Embedded Memory ECC Feature 4.3.16. FIFO Intel® FPGA IP Parameters 4.3.17. Reset Scheme
4.3.3. Specifications x
4.3.3.1. Verilog HDL Prototype 4.3.3.2. VHDL Component Declaration 4.3.3.3. VHDL LIBRARY-USE Declaration 4.3.3.4. HDL Code from Parameterizable Macros Template 4.3.3.5. FIFO Signals 4.3.3.6. FIFO Parameter Settings
4.3.8. FIFO Synchronous Clear and Asynchronous Clear Effect x
4.3.8.1. Recovery and Removal Timing Violation Warnings when Compiling a DCFIFO
4.3.11. DCFIFO Timing Constraint Setting x
4.3.11.1. Embedded Timing Constraint 4.3.11.2. User Configurable Timing Constraint
4.3.11.2. User Configurable Timing Constraint x
4.3.11.2.1. SDC Commands
4.4. Shift Register (RAM-based) Intel® FPGA IP x
4.4.1. Release Information for Shift Register (RAM-based) Intel® FPGA IP 4.4.2. Shift Register (RAM-based) Intel® FPGA IP Features 4.4.3. Shift Register (RAM-based) Intel® FPGA IP General Description 4.4.4. Shift Register (RAM-based) Intel® FPGA IP Parameter Settings 4.4.5. Shift Register Ports and Parameters Setting
1. Agilex™ 7 Embedded Memory Overview
2. Agilex™ 7 Embedded Memory Architecture and Features
3. Agilex™ 7 Embedded Memory Design Considerations
4. Agilex™ 7 Embedded Memory IP References
5. Agilex™ 7 Embedded Memory Debugging
6. Agilex™ 7 Embedded Memory User Guide Archives
7. Document Revision History for the Agilex™ 7 Embedded Memory User Guide

4.3.3.5. FIFO Signals

This section provides diagrams of the SCFIFO and DCFIFO blocks of the FIFO Intel® FPGA IP core to help in visualizing their input and output ports. This section also describes each port in detail to help in understanding their usages, functionality, or any restrictions. For better illustrations, some descriptions might refer you to a specific section in this user guide.
Figure 34. SCFIFO and DCFIFO Input and Output Signals

For the SCFIFO block, the read and write signals are synchronized to the same clock; for the DCFIFO block, the read and write signals are synchronized to the rdclk and wrclk clocks respectively. The prefixes wr and rd represent the signals that are synchronized by the wrclk and rdclk clocks respectively.

Table 39.  Input and Output Ports DescriptionThis table lists the signals of the FIFO Intel® FPGA IP core. The term “series” refers to all the device families of a particular device.
Port Type Required Description
clock 12 Input Yes Positive-edge-triggered clock.
wrclk 13 Input Yes Positive-edge-triggered clock.

Use to synchronize the following ports:

  • data
  • wrreq
  • wrfull
  • wrempty
  • wrusedw
rdclk 13 Input Yes Positive-edge-triggered clock.

Use to synchronize the following ports:

  • q
  • rdreq
  • rdfull
  • rdempty
  • rdusedw
data 14 Input Yes

Holds the data to be written in the FIFO Intel® FPGA IP core when the wrreq signal is asserted. If you manually instantiate the FIFO Intel® FPGA IP core, ensure the port width is equal to the lpm_width parameter.

wrreq 14 Input Yes Assert this signal to request for a write operation.

Ensure that the following conditions are met:

  • Do not assert the wrreq signal when the full (for SCFIFO) or wrfull (for DCFIFO) port is high. Enable the overflow protection circuitry or set the overflow_checking parameter to ON so that the FIFO Intel® FPGA IP core can automatically disable the wrreq signal when it is full.
  • The wrreq signal must meet the functional timing requirement based on the full or wrfull signal.
  • Do not assert the wrreq signal during the deassertion of the aclr signal. Violating this requirement creates a race condition between the falling edge of the aclr signal and the rising edge of the write clock if the wrreq port is set to high. For both the DCFIFO functions, you have the option to automatically add a circuit to synchronize the aclr signal with the wrclk clock, or set the write_aclr_synch parameter to ON. Use this option to ensure that the restriction is obeyed.
rdreq 14 Input Yes Assert this signal to request for a read operation. The rdreq signal acts differently in normal mode and show-ahead mode.

Ensure that the following conditions are met:

  • Do not assert the rdreq signal when the empty (for SCFIFO) or rdempty (for DCFIFO) port is high. Enable the underflow protection circuitry or set the underflow_checking parameter to ON so that the FIFO Intel® FPGA IP core can automatically disable the rdreq signal when it is empty.
  • The rdreq signal must meet the functional timing requirement based on the empty or rdempty signal.
sclr 12

aclr 14

Input No Assert this signal to clear all the output status ports, but the effect on the q output may vary for different FIFO configurations.

There are no minimum number of clock cycles for aclr signals that must remain active.

By default, the aclr port is enabled. Make sure either aclr or sclr port is enabled and included in the design to ensure the correct functionality of the FIFO.

q 14 Output Yes

Shows the data read from the read request operation. For the SCFIFO function and DCFIFO function, the width of the q port must be equal to the width of the data port. If you manually instantiate the FIFO functions, ensure that the port width is equal to the lpm_width parameter.

For the DCFIFO_MIXED_WIDTHS function, the width of the q port can be different from the width of the data port. If you manually instantiate the FIFO function, ensure that the width of the q port is equal to the lpm_width_r parameter. The FIFO function supports a wide write port with a narrow read port, and vice versa. However, the width ratio is restricted by the type of RAM block, and in general, are in the power of 2.

full 12

wrfull 13

rdfull 13

Output No When asserted, the FIFO Intel® FPGA IP core is considered full. Do not perform write request operation when the FIFO Intel® FPGA IP core is full.

In general, the rdfull signal is a delayed version of the wrfull signal. The rdfull signal functions as a combinational output instead of a derived version of the wrfull signal. Therefore, you must always refer to the wrfull port to ensure whether or not a valid write request operation can be performed, regardless of the target device.

empty 12

wrempty 13

rdempty 13

Output No When asserted, the FIFO Intel® FPGA IP core is considered empty. Do not perform read request operation when the FIFO Intel® FPGA IP core is empty.

In general, the wrempty signal is a delayed version of the rdempty signal. The wrempty signal functions as a combinational output instead of a derived version of the rdempty signal. Therefore, you must always refer to the rdempty port to ensure whether or not a valid read request operation can be performed, regardless of the target device.

almost_full 12 Output No Asserted when the usedw signal is greater than or equal to the almost_full_value parameter. It is used as an early indication of the full signal.
almost_empty 12 Output No Asserted when the usedw signal is less than the almost_empty_value parameter. It is used as an early indication of the empty signal. 15
usedw 12

wrusedw 13

rdusedw 13

Output No Show the number of words stored in the FIFO.

Ensure that the port width is equal to the lpm_widthu parameter if you manually instantiate the SCFIFO function or the DCFIFO function. For the DCFIFO_MIXED_WIDTH function, the width of the wrusedw and rdusedw ports must be equal to the LPM_WIDTHU and lpm_widthu_r parameters respectively.

The FIFO Intel® FPGA IP core shows full even before the number of words stored reaches its maximum value. Therefore, you must always refer to the full or wrfull port for valid write request operation, and the empty or rdempty port for valid read request operation regardless of the target device.
Note: Stored data may not be available for reading. Refer to FIFO Output Status Flag and Latency for "wrreq to empty" and "rdreq to empty" latency to ensure that the data is ready before reading the FIFO.
eccstatus 16 Output No A 2-bit wide error correction status port. Indicate whether the data that is read from the memory has an error in single-bit with correction, fatal error with no correction, or no error bit occurs.
  • 00: No error
  • 01: Illegal
  • 10: A correctable error occurred and the error has been corrected at the outputs; however, the memory array has not been updated.
  • 11:An uncorrectable error occurred and uncorrectable data appears at the output.

The DCFIFO function rdempty output may momentarily glitch when the aclr input is asserted. To prevent an external register from capturing this glitch incorrectly, ensure that one of the following is true:

  • The external register must use the same reset which is connected to the aclr input of the DCFIFO function, or
  • The reset connected to the aclr input of the DCFIFO function must be asserted synchronous to the clock which drives the external register.

The output latency information of the FIFO Intel® FPGA IP core is important, especially for the q output port, because there is no output flag to indicate when the output is valid to be sampled.

12 Only applicable for the SCFIFO function.
13 Applicable for both of the DCFIFO functions.
14 Applicable for the SCFIFO, DCFIFO, and DCFIFO_MIXED_WIDTH functions.
15 Under certain condition, the SCFIFO asserts the empty signal without ever asserting the almost_empty signal. Refer to SCFIFO ALMOST_EMPTY Functional Timing for more details.
16 Not applicable for the DCFIFO_MIXED_WIDTHS function.
Level Two Title