Intel® Quartus® Prime Standard Edition User Guide: Timing Analyzer

Download PDF
ID 683068
Date 2/21/2024
Public
Document Table of Contents
Document Table of Contents x
1. Timing Analysis Introduction 2. Using the Intel® Quartus® Prime Timing Analyzer A. Intel® Quartus® Prime Standard Edition User Guides
1. Timing Analysis Introduction x
1.1. Timing Analysis Basic Concepts 1.2. Document Revision History
1.1. Timing Analysis Basic Concepts x
1.1.1. Timing Path and Clock Analysis 1.1.2. Clock Setup Analysis 1.1.3. Clock Hold Analysis 1.1.4. Recovery and Removal Analysis 1.1.5. Multicycle Path Analysis 1.1.6. Metastability Analysis 1.1.7. Timing Pessimism 1.1.8. Clock-As-Data Analysis 1.1.9. Multicorner Analysis
1.1.1. Timing Path and Clock Analysis x
1.1.1.1. The Timing Netlist 1.1.1.2. Timing Paths 1.1.1.3. Data and Clock Arrival Times 1.1.1.4. Launch and Latch Edges
1.1.5. Multicycle Path Analysis x
1.1.5.1. Multicycle Clock Hold 1.1.5.2. Multicycle Clock Setup
2. Using the Intel® Quartus® Prime Timing Analyzer x
2.1. Enhanced Timing Analysis for Intel® Arria® 10 Devices 2.2. Basic Timing Analysis Flow 2.3. Using Timing Constraints 2.4. Timing Analyzer Tcl Commands 2.5. Timing Analysis of Imported Compilation Results 2.6. Using the Intel® Quartus® Prime Timing Analyzer Document Revision History
2.2. Basic Timing Analysis Flow x
2.2.1. Step 1: Open a Project and Run the Fitter 2.2.2. Step 2: Specify Timing Constraints 2.2.3. Step 3: Specify General Timing Analyzer Settings 2.2.4. Step 4: Run Timing Analysis 2.2.5. Step 5: Analyze Timing Analysis Results
2.2.5. Step 5: Analyze Timing Analysis Results x
2.2.5.1. Timing Report Commands 2.2.5.2. Set Operating Conditions 2.2.5.3. Fmax Summary Report 2.2.5.4. Report Timing Command 2.2.5.5. Correlating Constraints to the Timing Report 2.2.5.6. Locating Timing Paths in Other Tools
2.3. Using Timing Constraints x
2.3.1. Recommended Initial SDC Constraints 2.3.2. SDC File Precedence 2.3.3. Iterative Constraint Modification 2.3.4. Creating Clocks and Clock Constraints 2.3.5. Creating I/O Constraints 2.3.6. Creating Delay and Skew Constraints 2.3.7. Creating Timing Exceptions 2.3.8. Example Circuit and SDC File
2.3.1. Recommended Initial SDC Constraints x
2.3.1.1. Create Clock (create_clock) 2.3.1.2. Derive PLL Clocks (derive_pll_clocks) 2.3.1.3. Derive Clock Uncertainty (derive_clock_uncertainty) 2.3.1.4. Set Clock Groups (set_clock_groups)
2.3.4. Creating Clocks and Clock Constraints x
2.3.4.1. Creating Base Clocks 2.3.4.2. Creating Virtual Clocks 2.3.4.3. Creating Generated Clocks (create_generated_clock) 2.3.4.4. Deriving PLL Clocks 2.3.4.5. Creating Clock Groups (set_clock_groups) 2.3.4.6. Accounting for Clock Effect Characteristics
2.3.4.1. Creating Base Clocks x
2.3.4.1.1. Automatic Clock Detection and Constraint Creation
2.3.4.2. Creating Virtual Clocks x
2.3.4.2.1. Specifying I/O Interface Uncertainty 2.3.4.2.2. I/O Interface Clock Uncertainty Example
2.3.4.3. Creating Generated Clocks (create_generated_clock) x
2.3.4.3.1. Clock Divider Example (-divide_by) 2.3.4.3.2. Clock Multiplexor Example
2.3.4.5. Creating Clock Groups (set_clock_groups) x
2.3.4.5.1. Exclusive Clock Groups (-exclusive) 2.3.4.5.2. Asynchronous Clock Groups (-asynchronous) 2.3.4.5.3. set_clock_groups Constraint Tips
2.3.4.6. Accounting for Clock Effect Characteristics x
2.3.4.6.1. Set Clock Latency (set_clock_latency) 2.3.4.6.2. Clock Uncertainty
2.3.5. Creating I/O Constraints x
2.3.5.1. Input Constraints (set_input_delay) 2.3.5.2. Output Constraints (set_output_delay)
2.3.6. Creating Delay and Skew Constraints x
2.3.6.1. Advanced I/O Timing and Board Trace Model Delay 2.3.6.2. Maximum Skew (set_max_skew) 2.3.6.3. Net Delay (set_net_delay) 2.3.6.4. Create Timing Netlist
2.3.7. Creating Timing Exceptions x
2.3.7.1. Timing Constraint Precedence 2.3.7.2. False Paths (set_false_path) 2.3.7.3. Minimum and Maximum Delays 2.3.7.4. Multicycle Paths 2.3.7.5. Multicycle Exception Examples 2.3.7.6. Delay Annotation
2.3.7.4. Multicycle Paths x
2.3.7.4.1. Common Multicycle Applications 2.3.7.4.2. Relaxing Setup with Multicycle (set_multicyle_path) 2.3.7.4.3. Accounting for a Phase Shift (-phase)
2.3.7.5. Multicycle Exception Examples x
2.3.7.5.1. Default Multicycle Analysis 2.3.7.5.2. End Multicycle Setup = 2 and End Multicycle Hold = 0 2.3.7.5.3. End Multicycle Setup = 2 and End Multicycle Hold = 1 2.3.7.5.4. Same Frequency Clocks with Destination Clock Offset 2.3.7.5.5. Destination Clock Frequency is a Multiple of the Source Clock Frequency 2.3.7.5.6. Destination Clock Frequency is a Multiple of the Source Clock Frequency with an Offset 2.3.7.5.7. Source Clock Frequency is a Multiple of the Destination Clock Frequency 2.3.7.5.8. Source Clock Frequency is a Multiple of the Destination Clock Frequency with an Offset
2.4. Timing Analyzer Tcl Commands x
2.4.1. The quartus_sta Executable 2.4.2. Collection Commands 2.4.3. Identifying the Intel® Quartus® Prime Software Executable from the SDC File
2.4.2. Collection Commands x
2.4.2.1. Wildcard Characters 2.4.2.2. Adding and Removing Collection Items 2.4.2.3. Query of Collections 2.4.2.4. Using the get_pins Command
1. Timing Analysis Introduction
2. Using the Intel® Quartus® Prime Timing Analyzer
A. Intel® Quartus® Prime Standard Edition User Guides

2.3.4.6.1. Set Clock Latency (set_clock_latency)

The Set Clock Latency (set_clock_latency) constraint allows you to specify additional delay (that is, latency) in a clock network. This delay value represents the external delay from a virtual (or ideal) clock through the longest Late (-late) or shortest Early (-early) path, with reference to the Rise (-rise) or Fall (-fall) of the clock transition.

The Timing Analyzer uses the late clock latency for the data arrival path, and the early clock latency for the clock arrival path, when calculating setup analysis. The Timing Analyzer uses the early clock latency for the data arrival time, and the late clock latency for the clock arrival time, for hold analysis.

There are two forms of clock latency: clock source latency, and clock network latency. Source latency is the propagation delay from the origin of the clock to the clock definition point (for example, a clock port). Network latency is the propagation delay from a clock definition point to a register’s clock pin. The total latency at a register’s clock pin is the sum of the source and network latencies in the clock path.

To specify source latency to any clock ports in your design, use the set_clock_latency command.

Note: The Timing Analyzer automatically computes network latencies; therefore, you only can characterize source latency with the set_clock_latency command. You must use the -source option.
Level Two Title