Intel® Quartus® Prime Standard Edition User Guide: Timing Analyzer

Download PDF
ID 683068
Date 2/21/2024
Public
Document Table of Contents
Document Table of Contents x
1. Timing Analysis Introduction 2. Using the Intel® Quartus® Prime Timing Analyzer A. Intel® Quartus® Prime Standard Edition User Guides
1. Timing Analysis Introduction x
1.1. Timing Analysis Basic Concepts 1.2. Document Revision History
1.1. Timing Analysis Basic Concepts x
1.1.1. Timing Path and Clock Analysis 1.1.2. Clock Setup Analysis 1.1.3. Clock Hold Analysis 1.1.4. Recovery and Removal Analysis 1.1.5. Multicycle Path Analysis 1.1.6. Metastability Analysis 1.1.7. Timing Pessimism 1.1.8. Clock-As-Data Analysis 1.1.9. Multicorner Analysis
1.1.1. Timing Path and Clock Analysis x
1.1.1.1. The Timing Netlist 1.1.1.2. Timing Paths 1.1.1.3. Data and Clock Arrival Times 1.1.1.4. Launch and Latch Edges
1.1.5. Multicycle Path Analysis x
1.1.5.1. Multicycle Clock Hold 1.1.5.2. Multicycle Clock Setup
2. Using the Intel® Quartus® Prime Timing Analyzer x
2.1. Enhanced Timing Analysis for Intel® Arria® 10 Devices 2.2. Basic Timing Analysis Flow 2.3. Using Timing Constraints 2.4. Timing Analyzer Tcl Commands 2.5. Timing Analysis of Imported Compilation Results 2.6. Using the Intel® Quartus® Prime Timing Analyzer Document Revision History
2.2. Basic Timing Analysis Flow x
2.2.1. Step 1: Open a Project and Run the Fitter 2.2.2. Step 2: Specify Timing Constraints 2.2.3. Step 3: Specify General Timing Analyzer Settings 2.2.4. Step 4: Run Timing Analysis 2.2.5. Step 5: Analyze Timing Analysis Results
2.2.5. Step 5: Analyze Timing Analysis Results x
2.2.5.1. Timing Report Commands 2.2.5.2. Set Operating Conditions 2.2.5.3. Fmax Summary Report 2.2.5.4. Report Timing Command 2.2.5.5. Correlating Constraints to the Timing Report 2.2.5.6. Locating Timing Paths in Other Tools
2.3. Using Timing Constraints x
2.3.1. Recommended Initial SDC Constraints 2.3.2. SDC File Precedence 2.3.3. Iterative Constraint Modification 2.3.4. Creating Clocks and Clock Constraints 2.3.5. Creating I/O Constraints 2.3.6. Creating Delay and Skew Constraints 2.3.7. Creating Timing Exceptions 2.3.8. Example Circuit and SDC File
2.3.1. Recommended Initial SDC Constraints x
2.3.1.1. Create Clock (create_clock) 2.3.1.2. Derive PLL Clocks (derive_pll_clocks) 2.3.1.3. Derive Clock Uncertainty (derive_clock_uncertainty) 2.3.1.4. Set Clock Groups (set_clock_groups)
2.3.4. Creating Clocks and Clock Constraints x
2.3.4.1. Creating Base Clocks 2.3.4.2. Creating Virtual Clocks 2.3.4.3. Creating Generated Clocks (create_generated_clock) 2.3.4.4. Deriving PLL Clocks 2.3.4.5. Creating Clock Groups (set_clock_groups) 2.3.4.6. Accounting for Clock Effect Characteristics
2.3.4.1. Creating Base Clocks x
2.3.4.1.1. Automatic Clock Detection and Constraint Creation
2.3.4.2. Creating Virtual Clocks x
2.3.4.2.1. Specifying I/O Interface Uncertainty 2.3.4.2.2. I/O Interface Clock Uncertainty Example
2.3.4.3. Creating Generated Clocks (create_generated_clock) x
2.3.4.3.1. Clock Divider Example (-divide_by) 2.3.4.3.2. Clock Multiplexor Example
2.3.4.5. Creating Clock Groups (set_clock_groups) x
2.3.4.5.1. Exclusive Clock Groups (-exclusive) 2.3.4.5.2. Asynchronous Clock Groups (-asynchronous) 2.3.4.5.3. set_clock_groups Constraint Tips
2.3.4.6. Accounting for Clock Effect Characteristics x
2.3.4.6.1. Set Clock Latency (set_clock_latency) 2.3.4.6.2. Clock Uncertainty
2.3.5. Creating I/O Constraints x
2.3.5.1. Input Constraints (set_input_delay) 2.3.5.2. Output Constraints (set_output_delay)
2.3.6. Creating Delay and Skew Constraints x
2.3.6.1. Advanced I/O Timing and Board Trace Model Delay 2.3.6.2. Maximum Skew (set_max_skew) 2.3.6.3. Net Delay (set_net_delay) 2.3.6.4. Create Timing Netlist
2.3.7. Creating Timing Exceptions x
2.3.7.1. Timing Constraint Precedence 2.3.7.2. False Paths (set_false_path) 2.3.7.3. Minimum and Maximum Delays 2.3.7.4. Multicycle Paths 2.3.7.5. Multicycle Exception Examples 2.3.7.6. Delay Annotation
2.3.7.4. Multicycle Paths x
2.3.7.4.1. Common Multicycle Applications 2.3.7.4.2. Relaxing Setup with Multicycle (set_multicyle_path) 2.3.7.4.3. Accounting for a Phase Shift (-phase)
2.3.7.5. Multicycle Exception Examples x
2.3.7.5.1. Default Multicycle Analysis 2.3.7.5.2. End Multicycle Setup = 2 and End Multicycle Hold = 0 2.3.7.5.3. End Multicycle Setup = 2 and End Multicycle Hold = 1 2.3.7.5.4. Same Frequency Clocks with Destination Clock Offset 2.3.7.5.5. Destination Clock Frequency is a Multiple of the Source Clock Frequency 2.3.7.5.6. Destination Clock Frequency is a Multiple of the Source Clock Frequency with an Offset 2.3.7.5.7. Source Clock Frequency is a Multiple of the Destination Clock Frequency 2.3.7.5.8. Source Clock Frequency is a Multiple of the Destination Clock Frequency with an Offset
2.4. Timing Analyzer Tcl Commands x
2.4.1. The quartus_sta Executable 2.4.2. Collection Commands 2.4.3. Identifying the Intel® Quartus® Prime Software Executable from the SDC File
2.4.2. Collection Commands x
2.4.2.1. Wildcard Characters 2.4.2.2. Adding and Removing Collection Items 2.4.2.3. Query of Collections 2.4.2.4. Using the get_pins Command
1. Timing Analysis Introduction
2. Using the Intel® Quartus® Prime Timing Analyzer
A. Intel® Quartus® Prime Standard Edition User Guides

1.1.5.2. Multicycle Clock Setup

The setup relationship is defined as the number of clock periods between the latch edge and the launch edge. By default, the Timing Analyzer performs a single-cycle path analysis, which results in the setup relationship being equal to one clock period (latch edge – launch edge). Applying a multicycle setup assignment, adjusts the setup relationship by the multicycle setup value. The adjustment value may be negative.

An end multicycle setup assignment modifies the latch edge of the destination clock by moving the latch edge the specified number of clock periods to the right of the determined default latch edge. The following figure shows various values of the end multicycle setup (EMS) assignment and the resulting latch edge.

Figure 27. End Multicycle Setup Values

A start multicycle setup assignment modifies the launch edge of the source clock by moving the launch edge the specified number of clock periods to the left of the determined default launch edge. A start multicycle setup (SMS) assignment with various values can result in a specific launch edge.

Figure 28. Start Multicycle Setup Values

The setup relationship reported by the Timing Analyzer for the negative setup relationship.

Figure 29. Start Multicycle Setup Values Reported by the Timing Analyzer
Level Two Title