gmacgrp_interrupt_status
Register 14 (Interrupt Register)
The Interrupt Status register identifies the events in the MAC that can generate interrupt. All interrupt events are generated only when the corresponding optional feature is selected during core configuration and enabled during operation. Therefore, these bits are reserved when the corresponding features are not present in the core.
| Module Instance | Base Address | Register Address |
|---|---|---|
| i_emac_emac0 | 0xFF800000 | 0xFF800038 |
| i_emac_emac1 | 0xFF802000 | 0xFF802038 |
| i_emac_emac2 | 0xFF804000 | 0xFF804038 |
Size: 32
Offset: 0x38
Access: RO
| Bit Fields | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 |
|
reserved_31_12 RO 0x0 |
|||||||||||||||
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
|
reserved_31_12 RO 0x0 |
gpiis RO 0x0 |
lpiis RO 0x0 |
tsis RO 0x0 |
reserved_8 RO 0x0 |
mmcrxipis RO 0x0 |
mmctxis RO 0x0 |
mmcrxis RO 0x0 |
mmcis RO 0x0 |
pmtis RO 0x0 |
pcsancis RO 0x0 |
pcslchgis RO 0x0 |
rgsmiiis RO 0x0 |
|||
gmacgrp_interrupt_status Fields
| Bit | Name | Description | Access | Reset | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 31:12 | reserved_31_12 |
Reserved |
RO | 0x0 | ||||||
| 11 | gpiis |
GPI Interrupt Status When the GPIO feature is enabled, this bit is set when any active event (LL or LH) occurs on GPIS field (Bits [3:0]) of Register 56 (General Purpose IO Register) and the corresponding GPIE bit is enabled. This bit is cleared on reading the lane 0 (GPIS) of Register 56 (Genaral Purpose IO Register). When the GPIO feature is not enabled, this bit is reserved. |
RO | 0x0 | ||||||
| 10 | lpiis |
LPI Interrupt Status When the Energy Efficient Ethernet feature is enabled, this bit is set for any LPI state entry or exit in the MAC Transmitter or Receiver. This bit is cleared on reading Bit 0 of Register 12 (LPI Control and Status Register). In all other modes, this bit is reserved.
|
RO | 0x0 | ||||||
| 9 | tsis |
Timestamp Interrupt Status When the Advanced Timestamp feature is enabled, this bit is set when any of the following conditions is true: * The system time value equals or exceeds the value specified in the Target Time High and Low registers. * There is an overflow in the seconds register. * The Auxiliary snapshot trigger is asserted. This bit is cleared on reading Bit 0 of the Register 458 (Timestamp Status Register). If default Timestamping is enabled, when set, this bit indicates that the system time value is equal to or exceeds the value specified in the Target Time registers. In this mode, this bit is cleared after the completion of the read of this bit. In all other modes, this bit is reserved.
|
RO | 0x0 | ||||||
| 8 | reserved_8 |
Reserved |
RO | 0x0 | ||||||
| 7 | mmcrxipis |
MMC Receive Checksum Offload Interrupt Status This bit is set high when an interrupt is generated in the MMC Receive Checksum Offload Interrupt Register. This bit is cleared when all the bits in this interrupt register are cleared. This bit is valid only when you select the optional MMC module and Checksum Offload Engine (Type 2) during core configuration.
|
RO | 0x0 | ||||||
| 6 | mmctxis |
MMC Transmit Interrupt Status This bit is set high when an interrupt is generated in the MMC Transmit Interrupt Register. This bit is cleared when all the bits in this interrupt register are cleared. This bit is valid only when you select the optional MMC module during core configuration.
|
RO | 0x0 | ||||||
| 5 | mmcrxis |
MMC Receive Interrupt Status This bit is set high when an interrupt is generated in the MMC Receive Interrupt Register. This bit is cleared when all the bits in this interrupt register are cleared. This bit is valid only when you select the optional MMC module during core configuration.
|
RO | 0x0 | ||||||
| 4 | mmcis |
MMC Interrupt Status This bit is set high when any of the Bits [7:5] is set high and cleared only when all of these bits are low. This bit is valid only when you select the optional MMC module during core configuration.
|
RO | 0x0 | ||||||
| 3 | pmtis |
PMT Interrupt Status This bit is set when a Magic packet or Wake-on-LAN frame is received in the power-down mode (see Bits 5 and 6 in the PMT Control and Status Register). This bit is cleared when both Bits[6:5] are cleared because of a read operation to the PMT Control and Status register. This bit is valid only when you select the optional PMT module during core configuration. |
RO | 0x0 | ||||||
| 2 | pcsancis |
PCS Auto-Negotiation Complete This bit is set when the Auto-negotiation is completed in the TBI, RTBI, or SGMII PHY interface (Bit 5 in Register 49 (AN Status Register)). This bit is cleared when you perform a read operation to the AN Status register. This bit is valid only when you select the optional TBI, RTBI, or SGMII PHY interface during core configuration and operation. |
RO | 0x0 | ||||||
| 1 | pcslchgis |
PCS Link Status Changed This bit is set because of any change in Link Status in the TBI, RTBI, or SGMII PHY interface (Bit 2 in Register 49 (AN Status Register)). This bit is cleared when you perform a read operation on the AN Status register. This bit is valid only when you select the optional TBI, RTBI, or SGMII PHY interface during core configuration and operation. |
RO | 0x0 | ||||||
| 0 | rgsmiiis |
RGMII or SMII Interrupt Status This bit is set because of any change in value of the Link Status of RGMII or SMII interface (Bit 3 in Register 54 (SGMII/RGMII/SMII Status Register)). This bit is cleared when you perform a read operation on the SGMII/RGMII/SMII Status Register. This bit is valid only when you select the optional RGMII or SMII PHY interface during core configuration and operation.
|
RO | 0x0 |