intr_status3

Interrupt status register for bank 3

Module Instance	Base Address	Register Address
`nandregs`	`0xFFB80000`	`0xFFB80500`

Offset: 0x500

Access: RW

Important: To prevent indeterminate system behavior, reserved areas of memory must not be accessed by software or hardware. Any area of the memory map that is not explicitly defined as a register space or accessible memory is considered reserved.

Bit Fields
31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
`Reserved`
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
`page_xfer_inc` `RW 0x0`	`pipe_cmd_err` `RW 0x0`	`rst_comp` `RW 0x0`	`INT_act` `RW 0x0`	`unsup_cmd` `RW 0x0`	`locked_blk` `RW 0x0`	`pipe_cpybck_cmd_comp` `RW 0x0`	`erase_comp` `RW 0x0`	`program_comp` `RW 0x0`	`load_comp` `RW 0x0`	`erase_fail` `RW 0x0`	`program_fail` `RW 0x0`	`time_out` `RW 0x0`	`dma_cmd_comp` `RW 0x0`	`Reserved`	`ecc_uncor_err` `RW 0x0`

intr_status3 Fields

Bit	Name	Description	Access	Reset
15	`page_xfer_inc`	For every page of data transfer to or from the device, this bit will be set.	`RW`	`0x0`
14	`pipe_cmd_err`	A pipeline command sequence has been violated. This occurs when Map 01 page read/write address does not match the corresponding expected address from the pipeline commands issued earlier.	`RW`	`0x0`
13	`rst_comp`	The NAND Flash Memory Controller has completed its reset and initialization process	`RW`	`0x0`
12	`INT_act`	R/B pin of device transitioned from low to high	`RW`	`0x0`
11	`unsup_cmd`	An unsupported command was received. This interrupt is set when an invalid command is received, or when a command sequence is broken.	`RW`	`0x0`
10	`locked_blk`	The address to program or erase operation is to a locked block and the operation failed due to this reason	`RW`	`0x0`
9	`pipe_cpybck_cmd_comp`	A pipeline command or a copyback bank command has completed on this particular bank	`RW`	`0x0`
8	`erase_comp`	Device erase operation complete	`RW`	`0x0`
7	`program_comp`	Device finished the last issued program command.	`RW`	`0x0`
6	`load_comp`	Device finished the last issued load command.	`RW`	`0x0`
5	`erase_fail`	Erase failure occurred in the device on issuance of a erase command. err_block_addr and err_page_addr contain the block address and page address that failed erase operation.	`RW`	`0x0`
4	`program_fail`	Program failure occurred in the device on issuance of a program command. err_block_addr and err_page_addr contain the block address and page address that failed program operation.	`RW`	`0x0`
3	`time_out`	Watchdog timer has triggered in the controller due to one of the reasons like device not responding or controller state machine did not get back to idle	`RW`	`0x0`
2	`dma_cmd_comp`	A data DMA command has completed on this bank.	`RW`	`0x0`
1	`RSVD`	RSVD	`R`	`0x0`
0	`ecc_uncor_err`	Ecc logic detected uncorrectable error while reading data from flash device.	`RW`	`0x0`