UHS_REG_EXT

         
Name: UHS Register Extention
Size: 32 bits
Address Offset: 0x108
Read/Write access: read/write
      
Module Instance Base Address Register Address
i_sdmmc_sdmmc_block_0 0xFF808000 0xFF808108

Size: 32

Offset: 0x108

Access: RW

Important: The value of a reserved bit must be maintained in software. When you modify registers containing reserved bit fields, you must use a read-modify-write operation to preserve state and prevent indeterminate system behavior.
Bit Fields
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16

EXT_CLK_MUX_CTRL

RW 0x0

CLK_DRV_PHASE_CTRL

RW 0x0

CLK_SMPL_PHASE_CTRL

RW 0x0

15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

MMC_VOLT_REG_15

RW 0x0

MMC_VOLT_REG_14

RW 0x0

MMC_VOLT_REG_13

RW 0x0

MMC_VOLT_REG_12

RW 0x0

MMC_VOLT_REG_11

RW 0x0

MMC_VOLT_REG_10

RW 0x0

MMC_VOLT_REG_9

RW 0x0

MMC_VOLT_REG_8

RW 0x0

MMC_VOLT_REG_7

RW 0x0

MMC_VOLT_REG_6

RW 0x0

MMC_VOLT_REG_5

RW 0x0

MMC_VOLT_REG_4

RW 0x0

MMC_VOLT_REG_3

RW 0x0

MMC_VOLT_REG_2

RW 0x0

MMC_VOLT_REG_1

RW 0x0

MMC_VOLT_REG_0

RW 0x0

UHS_REG_EXT Fields

Bit Name Description Access Reset
31:30 EXT_CLK_MUX_CTRL
Input clock control for cclk_in. The MUX controlled by these bits exists outside DWC_mobile_storage IP.
RW 0x0
29:23 CLK_DRV_PHASE_CTRL
Control for amount of phase shift on cclk_in_drv clock. Can choose three MSBs to control delay lines and four LSBs to control phase shift; alternatively, use only LSBs.
RW 0x0
22:16 CLK_SMPL_PHASE_CTRL
Control for amount of phase shift on cclk_in_sample clock. Can choose three MSBs to control delay lines and four LSBs to control phase shift; alternatively, use only LSBs.
RW 0x0
15 MMC_VOLT_REG_15
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination 
with UHS_VOLT_REG to decode output selected voltage.
The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic.
Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. 
Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
Value Description
0x0 1.2V not supported
0x1 Support for 1.2V
RW 0x0
14 MMC_VOLT_REG_14
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination 
with UHS_VOLT_REG to decode output selected voltage.
The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic.
Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. 
Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
Value Description
0x0 1.2V not supported
0x1 Support for 1.2V
RW 0x0
13 MMC_VOLT_REG_13
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination 
with UHS_VOLT_REG to decode output selected voltage.
The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic.
Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. 
Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
Value Description
0x0 1.2V not supported
0x1 Support for 1.2V
RW 0x0
12 MMC_VOLT_REG_12
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination 
with UHS_VOLT_REG to decode output selected voltage.
The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic.
Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. 
Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
Value Description
0x0 1.2V not supported
0x1 Support for 1.2V
RW 0x0
11 MMC_VOLT_REG_11
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination 
with UHS_VOLT_REG to decode output selected voltage.
The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic.
Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. 
Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
Value Description
0x0 1.2V not supported
0x1 Support for 1.2V
RW 0x0
10 MMC_VOLT_REG_10
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination 
with UHS_VOLT_REG to decode output selected voltage.
The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic.
Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. 
Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
Value Description
0x0 1.2V not supported
0x1 Support for 1.2V
RW 0x0
9 MMC_VOLT_REG_9
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination 
with UHS_VOLT_REG to decode output selected voltage.
The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic.
Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. 
Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
Value Description
0x0 1.2V not supported
0x1 Support for 1.2V
RW 0x0
8 MMC_VOLT_REG_8
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination 
with UHS_VOLT_REG to decode output selected voltage.
The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic.
Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. 
Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
Value Description
0x0 1.2V not supported
0x1 Support for 1.2V
RW 0x0
7 MMC_VOLT_REG_7
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination 
with UHS_VOLT_REG to decode output selected voltage.
The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic.
Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. 
Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
Value Description
0x0 1.2V not supported
0x1 Support for 1.2V
RW 0x0
6 MMC_VOLT_REG_6
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination 
with UHS_VOLT_REG to decode output selected voltage.
The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic.
Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. 
Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
Value Description
0x0 1.2V not supported
0x1 Support for 1.2V
RW 0x0
5 MMC_VOLT_REG_5
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination 
with UHS_VOLT_REG to decode output selected voltage.
The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic.
Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. 
Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
Value Description
0x0 1.2V not supported
0x1 Support for 1.2V
RW 0x0
4 MMC_VOLT_REG_4
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination 
with UHS_VOLT_REG to decode output selected voltage.
The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic.
Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. 
Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
Value Description
0x0 1.2V not supported
0x1 Support for 1.2V
RW 0x0
3 MMC_VOLT_REG_3
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination 
with UHS_VOLT_REG to decode output selected voltage.
The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic.
Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. 
Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
Value Description
0x0 1.2V not supported
0x1 Support for 1.2V
RW 0x0
2 MMC_VOLT_REG_2
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination 
with UHS_VOLT_REG to decode output selected voltage.
The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic.
Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. 
Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
Value Description
0x0 1.2V not supported
0x1 Support for 1.2V
RW 0x0
1 MMC_VOLT_REG_1
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination 
with UHS_VOLT_REG to decode output selected voltage.
The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic.
Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. 
Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
Value Description
0x0 1.2V not supported
0x1 Support for 1.2V
RW 0x0
0 MMC_VOLT_REG_0
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination 
with UHS_VOLT_REG to decode output selected voltage.
The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic.
Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. 
Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
Value Description
0x0 1.2V not supported
0x1 Support for 1.2V
RW 0x0