UHS_REG_EXT
Name: UHS Register Extention
Size: 32 bits
Address Offset: 0x108
Read/Write access: read/write
| Module Instance | Base Address | Register Address |
|---|---|---|
| i_sdmmc_sdmmc_block_1 | 0xFF8D1000 | 0xFF8D1108 |
Size: 32
Offset: 0x108
Access: RW
| Bit Fields | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 |
|
EXT_CLK_MUX_CTRL RW 0x0 |
CLK_DRV_PHASE_CTRL RW 0x0 |
CLK_SMPL_PHASE_CTRL RW 0x0 |
|||||||||||||
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
|
MMC_VOLT_REG_15 RW 0x0 |
MMC_VOLT_REG_14 RW 0x0 |
MMC_VOLT_REG_13 RW 0x0 |
MMC_VOLT_REG_12 RW 0x0 |
MMC_VOLT_REG_11 RW 0x0 |
MMC_VOLT_REG_10 RW 0x0 |
MMC_VOLT_REG_9 RW 0x0 |
MMC_VOLT_REG_8 RW 0x0 |
MMC_VOLT_REG_7 RW 0x0 |
MMC_VOLT_REG_6 RW 0x0 |
MMC_VOLT_REG_5 RW 0x0 |
MMC_VOLT_REG_4 RW 0x0 |
MMC_VOLT_REG_3 RW 0x0 |
MMC_VOLT_REG_2 RW 0x0 |
MMC_VOLT_REG_1 RW 0x0 |
MMC_VOLT_REG_0 RW 0x0 |
UHS_REG_EXT Fields
| Bit | Name | Description | Access | Reset | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 31:30 | EXT_CLK_MUX_CTRL |
Input clock control for cclk_in. The MUX controlled by these bits exists outside DWC_mobile_storage IP. |
RW | 0x0 | ||||||
| 29:23 | CLK_DRV_PHASE_CTRL |
Control for amount of phase shift on cclk_in_drv clock. Can choose three MSBs to control delay lines and four LSBs to control phase shift; alternatively, use only LSBs. |
RW | 0x0 | ||||||
| 22:16 | CLK_SMPL_PHASE_CTRL |
Control for amount of phase shift on cclk_in_sample clock. Can choose three MSBs to control delay lines and four LSBs to control phase shift; alternatively, use only LSBs. |
RW | 0x0 | ||||||
| 15 | MMC_VOLT_REG_15 |
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination with UHS_VOLT_REG to decode output selected voltage. The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic. Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
|
RW | 0x0 | ||||||
| 14 | MMC_VOLT_REG_14 |
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination with UHS_VOLT_REG to decode output selected voltage. The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic. Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
|
RW | 0x0 | ||||||
| 13 | MMC_VOLT_REG_13 |
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination with UHS_VOLT_REG to decode output selected voltage. The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic. Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
|
RW | 0x0 | ||||||
| 12 | MMC_VOLT_REG_12 |
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination with UHS_VOLT_REG to decode output selected voltage. The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic. Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
|
RW | 0x0 | ||||||
| 11 | MMC_VOLT_REG_11 |
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination with UHS_VOLT_REG to decode output selected voltage. The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic. Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
|
RW | 0x0 | ||||||
| 10 | MMC_VOLT_REG_10 |
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination with UHS_VOLT_REG to decode output selected voltage. The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic. Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
|
RW | 0x0 | ||||||
| 9 | MMC_VOLT_REG_9 |
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination with UHS_VOLT_REG to decode output selected voltage. The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic. Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
|
RW | 0x0 | ||||||
| 8 | MMC_VOLT_REG_8 |
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination with UHS_VOLT_REG to decode output selected voltage. The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic. Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
|
RW | 0x0 | ||||||
| 7 | MMC_VOLT_REG_7 |
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination with UHS_VOLT_REG to decode output selected voltage. The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic. Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
|
RW | 0x0 | ||||||
| 6 | MMC_VOLT_REG_6 |
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination with UHS_VOLT_REG to decode output selected voltage. The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic. Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
|
RW | 0x0 | ||||||
| 5 | MMC_VOLT_REG_5 |
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination with UHS_VOLT_REG to decode output selected voltage. The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic. Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
|
RW | 0x0 | ||||||
| 4 | MMC_VOLT_REG_4 |
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination with UHS_VOLT_REG to decode output selected voltage. The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic. Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
|
RW | 0x0 | ||||||
| 3 | MMC_VOLT_REG_3 |
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination with UHS_VOLT_REG to decode output selected voltage. The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic. Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
|
RW | 0x0 | ||||||
| 2 | MMC_VOLT_REG_2 |
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination with UHS_VOLT_REG to decode output selected voltage. The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic. Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
|
RW | 0x0 | ||||||
| 1 | MMC_VOLT_REG_1 |
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination with UHS_VOLT_REG to decode output selected voltage. The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic. Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
|
RW | 0x0 | ||||||
| 0 | MMC_VOLT_REG_0 |
Support for 1.2V. MMC_VOLT_REG bits; must be read in combination with UHS_VOLT_REG to decode output selected voltage. The biu_volt_reg_1_2[NUM_CARD_BUS-1:0] signal decodes the voltage combination selected for the I/O voltage logic. Host controllers that support only SD standard or standard versions before eMMC4.41 do not program MMC_VOLT_REG. Only host controllers that support all three versions3.3,1.8,1.2 Vcan program MMC_VOLT_REG and connect biu_volt_reg_1_2.
|
RW | 0x0 |