chip_interleave_enable_and_allow_int_reads

Module Instance	Base Address	Register Address
`i_nand_dma`	`0xFFB80700`	`0xFFB80780`

Size: 32

Offset: 0x80

Access: RW

Important: The value of a reserved bit must be maintained in software. When you modify registers containing reserved bit fields, you must use a read-modify-write operation to preserve state and prevent indeterminate system behavior.

Bit Fields
31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
`Reserved`
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
`Reserved`							`cmd_dma_error_enable` `RW 0x1`	`Reserved`			`allow_int_reads_within_luns` `RW 0x1`	`Reserved`			`chip_interleave_enable` `RW 0x0`

chip_interleave_enable_and_allow_int_reads Fields

Bit	Name	Description	Access	Reset
8	`cmd_dma_error_enable`	This bit informs the CDMA channels to stop working on any new MAP10 Command DMAcommands from the host after encountering an error situation till the error bit for that corresponding channel is cleared in the cmd_dma_channel_error register by f/w. When the CDMA channel encounters an error, it will set the corresponding error bit in cmd_dma_channel_error register If this bit is set, the channel will stop executing any further commands till f/w comes and clears the error bit in the cmd_dma_channel_error_register. If this bit is not set, controller will still keep on executing new commands issued from f/w.	`RW`	`0x1`
4	`allow_int_reads_within_luns`	This bit informs the controller to enable or disable simultaneous read accesses to different LUNS in the same bank. This bit is of importance only if the controller supports interleaved operations among LUNs and if the device has multiple LUNS. If the bit is disabled, the controller will send read commands to different LUNS of of the same bank only sequentially and if enabled, the controller will issue simultaneous read accesses to LUNS of same bank if required. [list][]1 - Enable []0 - Disable[/list]	`RW`	`0x1`
0	`chip_interleave_enable`	This bit informs the controller to enable or disable interleaving among banks/LUNS to increase the net performance of the controller. [list][]1 - Enable interleaving []0 - Disable Interleaving[/list]	`RW`	`0x0`

Bit

Name

Description

Access

Reset

cmd_dma_error_enable

This bit informs the CDMA channels to stop working on any new MAP10 Command DMAcommands from the host after encountering an
                 error situation till the error bit for that corresponding channel is cleared in the cmd_dma_channel_error register by f/w.
                 When the CDMA channel encounters an error, it will set the corresponding error bit in cmd_dma_channel_error register
                 If this bit is set, the channel will stop executing any further commands 
                 till f/w comes and clears the error bit in the cmd_dma_channel_error_register.
                 If this bit is not set, controller will still keep on executing new commands issued from f/w.

RW

0x1

allow_int_reads_within_luns

This bit informs the controller to enable or disable simultaneous read accesses
                  to different LUNS in the same bank. This bit is of importance only if the controller
                  supports interleaved operations among LUNs and if the device has multiple LUNS.
                  If the bit is disabled, the controller will send read commands to different LUNS of 
                  of the same bank only sequentially and if enabled, the controller will issue simultaneous
                  read accesses to LUNS of same bank if required.
                  [list][*]1 - Enable  [*]0 - Disable[/list]

RW

0x1

chip_interleave_enable

This bit informs the controller to enable or disable interleaving
                  among banks/LUNS to increase the net performance of the controller. 
                  [list][*]1 - Enable interleaving  [*]0 - Disable Interleaving[/list]

RW

0x0