MACsec Intel® FPGA IP User Guide

Download PDF
ID 736108
Date 3/31/2024
Public
Document Table of Contents
Document Table of Contents x
1. Introduction 2. Interface Overview 3. Parameters 4. Designing with the IP Core 5. Functional Description 6. Configuration Registers for MACsec IP 7. MACsec Intel® FPGA IP Example Design 8. MACsec Intel FPGA IP User Guide Archives 9. Document Revision History for the MACsec Intel FPGA IP User Guide
1. Introduction x
1.1. Terminology 1.2. IP Core Overview 1.3. Release Information 1.4. Device Family Support 1.5. Device Speed Grade Support and Theoretical Throughput 1.6. Resource Utilization
1.2. IP Core Overview x
1.2.1. IP Description 1.2.2. IP Core Applications
1.2.2. IP Core Applications x
1.2.2.1. SmartNIC 1.2.2.2. Ethernet Bridge + Inline MACsec
2. Interface Overview x
2.1. Block Diagram 2.2. Interfaces 2.3. Clocking Domains
2.2. Interfaces x
2.2.1. IP Interface Signals 2.2.2. IP Interface Signal Timing Diagram/Waveforms 2.2.3. Clocks, Resets, and Interrupts
2.2.1. IP Interface Signals x
2.2.1.1. Common Port Mux Interface 2.2.1.2. Common Port Demux Interface 2.2.1.3. Controlled Port Mux Interface 2.2.1.4. Controlled Port Demux Interface 2.2.1.5. Uncontrolled Port RX Interface 2.2.1.6. Uncontrolled Port TX Interface 2.2.1.7. Management Interface 2.2.1.8. Decrypt Port Mux Management Interface 2.2.1.9. Decrypt Port Demux Management Interface 2.2.1.10. Encrypt Port Mux Management Interface 2.2.1.11. Encrypt Port Demux Management Interface 2.2.1.12. Crypto IP Management Bus 2.2.1.13. Miscellaneous Control Signals
2.2.2. IP Interface Signal Timing Diagram/Waveforms x
2.2.2.1. Common Port Mux Interface Waveform 2.2.2.2. Common Port Demux Interface Waveform 2.2.2.3. Controlled Port Mux Interface Waveform 2.2.2.4. Controlled Port Demux Interface Waveform 2.2.2.5. Uncontrolled Port RX Interface Waveform 2.2.2.6. Uncontrolled Port TX Interface Waveform 2.2.2.7. Crypto RX Waveform 2.2.2.8. Crypto TX Waveform 2.2.2.9. MACsec Management Interface (Read) 2.2.2.10. MACsec Management Interface (Write)
3. Parameters x
3.1. MACsec Intel FPGA IP Parameter Settings
4. Designing with the IP Core x
4.1. Installing and Licensing Intel® FPGA IP Cores 4.2. Specifying the IP Core Parameters and Options 4.3. Generated File Structure 4.4. Reset Transactions 4.5. MACsec Software Initialization Sequence
4.1. Installing and Licensing Intel® FPGA IP Cores x
4.1.1. Intel® FPGA IP Evaluation Mode
5. Functional Description x
5.1. AXI-ST Common/Controlled/Uncontrolled Ports 5.2. Packet Parser and Classifier 5.3. SA Lookup and Update 5.4. Encryption Framer/DeFramer 5.5. Decryption Framer/Deframer 5.6. Packet Aggregator/Disaggregator 5.7. Cryptographic AES 5.8. Error Handling 5.9. Packet Statistics
5.1. AXI-ST Common/Controlled/Uncontrolled Ports x
5.1.1. AXI-ST Single Packet Mode 5.1.2. AXI-ST Multi Packet Mode 5.1.3. User Interface Data Streaming 5.1.4. AXI-ST Ready Latency 5.1.5. Port and Secure Channel Mapping 5.1.6. Port and Crypto Channel Mapping 5.1.7. Minimum Packet Size 5.1.8. Byte Ordering 5.1.9. Controlled/Uncontrolled Port Muxing
5.1.3. User Interface Data Streaming x
5.1.3.1. Single Packet Mode Data Stream 5.1.3.2. Multi Packet Mode Data Stream
5.2. Packet Parser and Classifier x
5.2.1. Packet Parser 5.2.2. Packet Classifier
5.3. SA Lookup and Update x
5.3.1. Packet Actions 5.3.2. Packet Buffer 5.3.3. New Channel Assignment 5.3.4. Anti-Replay Protection
5.3.1. Packet Actions x
5.3.1.1. Packet Encrypt 5.3.1.2. Packet Decrypt 5.3.1.3. Packet Discard 5.3.1.4. PDU Validation
5.4. Encryption Framer/DeFramer x
5.4.1. Channel Allocation 5.4.2. Packet Framer 5.4.3. VLAN Tagging
5.4.2. Packet Framer x
5.4.2.1. Bypass Packet 5.4.2.2. Stream Interleaving
5.4.3. VLAN Tagging x
5.4.3.1. No VLAN Tag 5.4.3.2. VLAN Tag (Not in Clear) 5.4.3.3. VLAN Tag (Clear)
5.5. Decryption Framer/Deframer x
5.5.1. XPN Recovery 5.5.2. Replay Check Update 5.5.3. Packet Deframer
5.6. Packet Aggregator/Disaggregator x
5.6.1. Packet Aggregator 5.6.2. Packet Disaggregator
5.7. Cryptographic AES x
5.7.1. Register Address Ordering 5.7.2. Byte Order Swapping 5.7.3. Byte Ordering
5.8. Error Handling x
5.8.1. Packet Error Handling 5.8.2. Memory Blocks ECC Errors 5.8.3. Crypto Errors 5.8.4. System-Level Errors
7. MACsec Intel® FPGA IP Example Design x
7.1. Simulation Requirements 7.2. Steps to Run Simulation 7.3. Port Configurations 7.4. Multi Interface Buffering Muxing/Demuxing 7.5. 4x25 GbE (Encryption + Decryption) 7.6. Packet Generator/Checker 7.7. Clocking
1. Introduction
2. Interface Overview
3. Parameters
4. Designing with the IP Core
5. Functional Description
6. Configuration Registers for MACsec IP
7. MACsec Intel® FPGA IP Example Design
8. MACsec Intel FPGA IP User Guide Archives
9. Document Revision History for the MACsec Intel FPGA IP User Guide

4.5. MACsec Software Initialization Sequence

To bring up a port as a MACsec control port, there is an initialization sequence that needs to be followed.

Follow the steps below to start the initialization sequence:

  1. Set “Control port enable” to False (the default value is False).
  2. Program the per-MACsec instance configuration:
    1. Set all the global stats counters to 0x0 (default is 0x0).
    2. Set the key length (False – 128 bits; True – 256 bits) for the MACsec instance associated with the port.
    3. Set the extended packet numbering mode for the MACsec instance associated with the port (False – regular packet numbering; True – extended packet numbering).
    4. Zeroing port SAs (GLOBAL_ZERO CSR).
    5. Optional: Set the confidentiality offset for the MACsec instance (default is 0x0).
  3. Program the Tx Configuration:
    1. Set the Tx basic configuration for the MACsec instance.
    2. Set the packet numbering limit value for the MACsec instance.
    3. Set the maximum packet bytes supported value for the MACsec instance.
    4. Set the SCI value for the port.
  4. Choose a security association and program the following configuration:
    1. Set the Key value for the SA.
    2. Set the next packet number value for the SA.
    3. Set the confidentiality offset value for the SA.
    4. Initialize all the stats configuration.
  5. Set the SA value to the chosen security association.
  6. Program the Rx Configuration:
    1. Set the Rx basic configuration for the MACsec instance.
    2. Set the replay window length if the replay protect is enabled for the MACsec instance.
    3. Set the default SCI per port.
  7. Program the security channel that is used on the lane by configuring:
    1. Set the SCI value for the security channel.
    2. Initialize all the stats configuration.
  8. Choose a security association and program the following configuration:
    1. Set the Key value for the SA belonging to the SC.
    2. Set the next packet number value for the SA belonging to the SC.
    3. Set the lowest PN value for SA belonging to the SC.
    4. Initialize all the stats configuration.
  9. Set the SA value to the chosen security association. If there are multiple security associations programmed on Rx, enable them.
  10. Once all of the above is programmed, enable the port as a control port.
Level Two Title