F-Tile PMA and FEC Direct PHY Multirate Intel® FPGA IP User Guide

Download PDF
ID 720998
Date 4/01/2024
Public
Document Table of Contents
Document Table of Contents x
1. Introduction 2. Interface Overview 3. Parameters 4. Designing with the IP Core 5. Block Description 6. Configuration Registers Overview 7. F-Tile PMA and FEC Direct PHY Multirate Intel® FPGA IP User Guide Archives 8. Document Revision History for the F-Tile PMA and FEC Direct PHY Multirate Intel® FPGA IP User Guide
1. Introduction x
1.1. IP Core Overview 1.2. Release Information 1.3. Device Family Support 1.4. Device Speed Grade Support 1.5. Resource Utilization 1.6. Related Documentation
1.1. IP Core Overview x
1.1.1. Reconfiguration Group 1.1.2. Base Profile 1.1.3. Secondary Profiles 1.1.4. Startup Profile 1.1.5. Supported Reconfiguration Groups
2. Interface Overview x
2.1. Clock Signals 2.2. Reset Signals 2.3. TX and RX Parallel and Serial Signals 2.4. Custom Cadence Control and Status Signals 2.5. TX and RX PMA Status Signals 2.6. RS-FEC Signals 2.7. TX and RX PMA FIFO Signals 2.8. PMA Avalon Memory-Mapped Signals 2.9. Datapath Avalon Memory-Mapped Signals
3. Parameters x
3.1. Dynamic Reconfiguration QSF Settings 3.2. QSF settings for Different Reconfiguration Profiles 3.3. Generating IP-XACT File
3.2. QSF settings for Different Reconfiguration Profiles x
3.2.1. Bypass RX Adaptation QSF Settings
4. Designing with the IP Core x
4.1. Installing and Licensing Intel® FPGA IP Cores 4.2. Specifying the IP Core Parameters and Options 4.3. Generated File Structure 4.4. Configuring the F-Tile PMA/FEC Direct PHY Multirate Intel FPGA IP Core
4.1. Installing and Licensing Intel® FPGA IP Cores x
4.1.1. Intel® FPGA IP Evaluation Mode
4.2. Specifying the IP Core Parameters and Options x
4.2.1. Reference and System PLL Clock for your IP Design
4.4. Configuring the F-Tile PMA/FEC Direct PHY Multirate Intel FPGA IP Core x
4.4.1. Steps to Configure the F-Tile PMA/FEC Direct PHY Multirate Intel FPGA IP Core
6. Configuration Registers Overview x
6.1. Controlling the Reconfiguration Soft CSR Registers for Dynamic Reconfiguration 6.2. Configuration Registers
6.2. Configuration Registers x
6.2.1. F-Tile PMA/FEC Direct PHY Intel FPGA IP Core Soft CSR Registers 6.2.2. F-Tile PMA/FEC Direct PHY Multirate Intel® FPGA IP Core Soft CSR Registers
6.2.1. F-Tile PMA/FEC Direct PHY Intel FPGA IP Core Soft CSR Registers x
6.2.1.1. Controlling the Reconfiguration Soft CSR with Fractures
1. Introduction
2. Interface Overview
3. Parameters
4. Designing with the IP Core
5. Block Description
6. Configuration Registers Overview
7. F-Tile PMA and FEC Direct PHY Multirate Intel® FPGA IP User Guide Archives
8. Document Revision History for the F-Tile PMA and FEC Direct PHY Multirate Intel® FPGA IP User Guide

1.1.3. Secondary Profiles

A secondary profile is a PMA direct or FEC direct setting that you want to dynamically reconfigure to.

There are a total of 32 secondary profiles you can enable for each F-Tile PMA/FEC Direct PHY Multirate Intel FPGA IP. The secondary profiles must use all of the PMA lanes allocated for the reconfiguration group, either within a single profile or in multiple profiles by using the same Profile group id.

The Profile #N IP Configuration sub tab is where you can configure the different Reconfiguration subset, Target fracture, Profile group id parameters and Use profile for startup option. These parameters and option are new in this IP. For more information about these parameter settings, refer to Parameter Settings: Profile #N (N=0-32) Tab.

You also have to configure the Common Datapath, TX Datapath, RX Datapath and RS-FEC options for your PMA channel to reflect your targeted reconfiguration profiles. IP Port selection is not available in secondary profiles settings.

Level Two Title