F-Tile PMA and FEC Direct PHY Multirate Intel® FPGA IP User Guide

Download PDF
ID 720998
Date 4/01/2024
Public
Document Table of Contents
Document Table of Contents x
1. Introduction 2. Interface Overview 3. Parameters 4. Designing with the IP Core 5. Block Description 6. Configuration Registers Overview 7. F-Tile PMA and FEC Direct PHY Multirate Intel® FPGA IP User Guide Archives 8. Document Revision History for the F-Tile PMA and FEC Direct PHY Multirate Intel® FPGA IP User Guide
1. Introduction x
1.1. IP Core Overview 1.2. Release Information 1.3. Device Family Support 1.4. Device Speed Grade Support 1.5. Resource Utilization 1.6. Related Documentation
1.1. IP Core Overview x
1.1.1. Reconfiguration Group 1.1.2. Base Profile 1.1.3. Secondary Profiles 1.1.4. Startup Profile 1.1.5. Supported Reconfiguration Groups
2. Interface Overview x
2.1. Clock Signals 2.2. Reset Signals 2.3. TX and RX Parallel and Serial Signals 2.4. Custom Cadence Control and Status Signals 2.5. TX and RX PMA Status Signals 2.6. RS-FEC Signals 2.7. TX and RX PMA FIFO Signals 2.8. PMA Avalon Memory-Mapped Signals 2.9. Datapath Avalon Memory-Mapped Signals
3. Parameters x
3.1. Dynamic Reconfiguration QSF Settings 3.2. QSF settings for Different Reconfiguration Profiles 3.3. Generating IP-XACT File
3.2. QSF settings for Different Reconfiguration Profiles x
3.2.1. Bypass RX Adaptation QSF Settings
4. Designing with the IP Core x
4.1. Installing and Licensing Intel® FPGA IP Cores 4.2. Specifying the IP Core Parameters and Options 4.3. Generated File Structure 4.4. Configuring the F-Tile PMA/FEC Direct PHY Multirate Intel FPGA IP Core
4.1. Installing and Licensing Intel® FPGA IP Cores x
4.1.1. Intel® FPGA IP Evaluation Mode
4.2. Specifying the IP Core Parameters and Options x
4.2.1. Reference and System PLL Clock for your IP Design
4.4. Configuring the F-Tile PMA/FEC Direct PHY Multirate Intel FPGA IP Core x
4.4.1. Steps to Configure the F-Tile PMA/FEC Direct PHY Multirate Intel FPGA IP Core
6. Configuration Registers Overview x
6.1. Controlling the Reconfiguration Soft CSR Registers for Dynamic Reconfiguration 6.2. Configuration Registers
6.2. Configuration Registers x
6.2.1. F-Tile PMA/FEC Direct PHY Intel FPGA IP Core Soft CSR Registers 6.2.2. F-Tile PMA/FEC Direct PHY Multirate Intel® FPGA IP Core Soft CSR Registers
6.2.1. F-Tile PMA/FEC Direct PHY Intel FPGA IP Core Soft CSR Registers x
6.2.1.1. Controlling the Reconfiguration Soft CSR with Fractures
1. Introduction
2. Interface Overview
3. Parameters
4. Designing with the IP Core
5. Block Description
6. Configuration Registers Overview
7. F-Tile PMA and FEC Direct PHY Multirate Intel® FPGA IP User Guide Archives
8. Document Revision History for the F-Tile PMA and FEC Direct PHY Multirate Intel® FPGA IP User Guide

2.8. PMA Avalon Memory-Mapped Signals

The following table describes the PMA Avalon® memory-mapped signals that are a part of the F-Tile PMA/FEC Direct PHY Multirate Intel FPGA IP.

Table 15.  PMA Avalon® Memory-Mapped Interface SignalsRefer to Variables Defining Bits for the Interfacing Ports in Port and Signal Reference for full variable definitions.
Signal Name Clocks Domain/Resets Direction Description
reconfig_xcvr_clk N/A Input Reconfiguration Interface Clock
reconfig_xcvr_reset reconfig_xcvr_clk Input PMA reconfiguration interface reset. You must assert this reset at least once after power on.
reconfig_xcvr_address[17+K p:0] reconfig_xcvr_clk Input Reconfiguration Interface Address K p=Ceiling(log2(N)). Upper address bits are for shared PMA decoding if more than one PMA exists.
reconfig_xcvr_byteenable[3:0] reconfig_xcvr_clk Input Byte Enable. If byteenable[3:0] is 4’b1111, uses 32-bit Dword Access; otherwise uses byte access.
reconfig_xcvr_write reconfig_xcvr_clk Input Reconfiguration Write
reconfig_xcvr_read reconfig_xcvr_clk Input Reconfiguration Read
reconfig_xcvr_writedata[31:0] reconfig_xcvr_clk Input Reconfiguration Write data
reconfig_xcvr_readdata[31:0] reconfig_xcvr_clk Output Reconfiguration Read data
reconfig_xcvr_waitrequest reconfig_xcvr_clk Output Reconfiguration Wait Request
reconfig_xcvr_readdatavalid reconfig_xcvr_clk Output Reconfiguration Read Data Valid. Optional port, available if the port is enabled in parameter editor.
Level Two Title