F-Tile Ethernet Multirate Intel® FPGA IP User Guide

Download PDF
ID 714307
Date 5/01/2024
Public
Document Table of Contents
Document Table of Contents x
1. Introduction 2. Interface Overview 3. Parameters 4. Designing with the IP Core 5. Block Description 6. Configuration Registers 7. F-Tile Ethernet Multirate Intel FPGA IP User Guide Archives 8. Document Revision History for the F-Tile Ethernet Multirate Intel FPGA IP User Guide
1. Introduction x
1.1. Overview 1.2. Release Information 1.3. Device Family Support 1.4. Device Speed Grade Support 1.5. Resource Utilization 1.6. Related Documentation 1.7. F-Tile Ethernet Multirate IP Core Features and Constraints 1.8. F-Tile Ethernet Multirate IP Core Concepts
1.8. F-Tile Ethernet Multirate IP Core Concepts x
1.8.1. Reconfiguration Group 1.8.2. Base Profile 1.8.3. Secondary Profile 1.8.4. Secondary Profile Group 1.8.5. Startup Profile 1.8.6. Supported Reconfiguration Groups 1.8.7. PTP Timestamp Accuracy Support 1.8.8. Transceiver Lane Mapping
2. Interface Overview x
2.1. Port Numbering Scheme 2.2. Clock Signals 2.3. Reset Signals 2.4. Fractured MAC Segmented Interface for FGT Transceivers 2.5. Fractured MAC Segmented Interface for FHT Transceivers 2.6. Fractured MAC Avalon ST Client Interface for FGT Transceivers 2.7. Fractured MAC Avalon ST Client Interface for FHT Transceivers 2.8. Fractured MII PCS-Only Interface for FGT Transceivers 2.9. Fractured MII PCS-Only Interface for FHT Transceivers 2.10. Fractured PCS66 Interface for OTN/FlexE for FGT Transceivers 2.11. Fractured PCS66 Interface for OTN/FlexE for FHT Transceivers 2.12. MAC Flow Control Interface 2.13. Status Interface 2.14. Avalon® Memory-Mapped Reconfiguration Interfaces 2.15. Auto-Negotiation and Link Training Interface 2.16. Precision Time Protocol Interface
2.16. Precision Time Protocol Interface x
2.16.1. PTP Clock Interface 2.16.2. Time-of-Day Interface 2.16.3. TX 2-Step Timestamp Interface 2.16.4. TX 1-Step Timestamp Interface 2.16.5. RX Timestamp Interface 2.16.6. PTP Status Interface 2.16.7. PTP Tile Interface
4. Designing with the IP Core x
4.1. Specifying the IP Core Parameters and Options 4.2. Generated File Structure
4.1. Specifying the IP Core Parameters and Options x
4.1.1. Reference and System PLL Clock for your IP Design
5. Block Description x
5.1. Precision Time Protocol
1. Introduction
2. Interface Overview
3. Parameters
4. Designing with the IP Core
5. Block Description
6. Configuration Registers
7. F-Tile Ethernet Multirate Intel FPGA IP User Guide Archives
8. Document Revision History for the F-Tile Ethernet Multirate Intel FPGA IP User Guide

1.1. Overview

Dynamic reconfiguration in F-tile supports two types of solutions: separate soft IP and shared soft IP.

The separate soft IP solution instantiates a single instance of different IPs such as the F-Tile Ethernet Intel® FPGA Hard IP, F-Tile CPRI PHY Intel® FPGA IP, or F-Tile PMA and FEC Direct PHY Intel® FPGA IP, combined to reconfigure over an identified set of transceiver channels. The soft IP logic remains separate for each instance. Along with the single instance, you must configure the F-Tile Dynamic Reconfiguration Suite Intel FPGA IP to perform the reconfiguration setup and the data path to the EMIBs.

The multirate soft IP addresses the limitation of the separate soft IP method by providing the resource optimization. The multirate soft IP core supports different Ethernet configurations based on the control status register (CSR) programming.

Figure 1. Example of the Separate Soft IP Dynamic Reconfiguration in F-Tile

This document describes the shared soft F-Tile Ethernet Multirate Intel® FPGA IP solution for the dynamic reconfiguration in F-tile.

Related Information
Level Two Title