F-Tile Interlaken Intel® FPGA IP User Guide

Download PDF
ID 683622
Date 10/02/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the F-Tile Interlaken Intel® FPGA IP Core 2. Getting Started 3. Parameter Settings 4. Functional Description 5. Interface Signals 6. IP Registers 7. F-Tile Interlaken Intel® FPGA IP User Guide Archives 8. Document Revision History for F-Tile Interlaken Intel FPGA IP User Guide
1. About the F-Tile Interlaken Intel® FPGA IP Core x
1.1. Features 1.2. Device Family Support 1.3. Device Speed Grade Support 1.4. Performance and Resource Utilization 1.5. Round-trip Latency 1.6. Release Information
2. Getting Started x
2.1. Installing and Licensing Intel® FPGA IPs 2.2. Generated File Structure 2.3. Specifying the IP Core Parameters and Options 2.4. Analog Parameter Settings 2.5. Reference and System PLL Clock for your IP Design 2.6. Simulating the IP Core 2.7. Compiling the Full Design and Programming the FPGA
2.1. Installing and Licensing Intel® FPGA IPs x
2.1.1. Intel® FPGA IP Evaluation Mode
2.5. Reference and System PLL Clock for your IP Design x
2.5.1. System PLL Configuration
4. Functional Description x
4.1. Data Path Flow 4.2. Interlaken Look-aside Data Path Flow 4.3. Modes of Operation 4.4. Performance 4.5. IP Reset 4.6. M20K ECC Support 4.7. Out-of-Band Flow Control 4.8. 32-bit Soft CWBIN Counters
4.1. Data Path Flow x
4.1.1. Interlaken TX Path 4.1.2. Interlaken RX Path
4.1.1. Interlaken TX Path x
4.1.1.1. Transmit Path Blocks 4.1.1.2. In-Band Calendar Bits on Transmit Side
4.1.2. Interlaken RX Path x
4.1.2.1. Receive Path Blocks 4.1.2.2. In-Band Calendar Bits on Receive Side 4.1.2.3. RX Errored Packet Handling
4.1.2.3. RX Errored Packet Handling x
4.1.2.3.1. Example With Errors and In-Band Calendar Bits
4.2. Interlaken Look-aside Data Path Flow x
4.2.1. Interlaken Look-aside TX Path 4.2.2. Interlaken Look-aside RX Path
4.2.1. Interlaken Look-aside TX Path x
4.2.1.1. Transmit Path Blocks
4.2.2. Interlaken Look-aside RX Path x
4.2.2.1. Receive Path Blocks 4.2.2.2. RX Error Handling
4.3. Modes of Operation x
4.3.1. Interleaved and Packet Modes 4.3.2. Multi-Segment Mode 4.3.3. Interlaken Look-aside Mode
4.3.1. Interleaved and Packet Modes x
4.3.1.1. Transmit User Data Interface Examples 4.3.1.2. Receive User Data Interface Example
4.3.2. Multi-Segment Mode x
4.3.2.1. Multi-Segment Interface Example
4.3.3. Interlaken Look-aside Mode x
4.3.3.1. Transmit User Data Interface Example 4.3.3.2. Receive User Data Interface Example
5. Interface Signals x
5.1. Clock and Reset Interface Signals 5.2. Transmit User Interface Signals 5.3. Receive User Interface Signals 5.4. Management Interface Signals 5.5. Reconfiguration Interface Signals 5.6. Interlaken Link and Miscellaneous Signals
1. About the F-Tile Interlaken Intel® FPGA IP Core
2. Getting Started
3. Parameter Settings
4. Functional Description
5. Interface Signals
6. IP Registers
7. F-Tile Interlaken Intel® FPGA IP User Guide Archives
8. Document Revision History for F-Tile Interlaken Intel FPGA IP User Guide

2.7. Compiling the Full Design and Programming the FPGA

You can use the Start Compilation command on the Processing menu in the Intel® Quartus® Prime software to compile your design. After successfully compiling your design, program the targeted Intel® device with the Programmer and verify the design in hardware.

Intel® Quartus® Prime may give a critical warning if the HSSI parameters in the Intel® Quartus® Prime settings file (.qsf) to configure the FHT and FGT PMAs are not specified.

You can refer to F-Tile Architecture and PMA and FEC Direct PHY IP User Guide (Section 3.12. Configurable Intel® Quartus® Prime Software Settings) to configure the FHT and FGT PMAs using the Intel® Quartus® Prime software settings file. (.qsf)

Related Information
Level Two Title