Intel® Stratix® 10 Hard Processor System Component Reference Manual

Download PDF
ID 683516
Date 2/10/2023
Public
Document Table of Contents
Document Table of Contents x
1. Introduction to the Intel® Stratix® 10 Hard Processor System Component 2. Configuring the Intel® Stratix® 10 Hard Processor System Component 3. Simulating the Intel® Stratix® 10 HPS Component
1. Introduction to the Intel® Stratix® 10 Hard Processor System Component x
1.1. Cortex*-A53 MPCore* Processor 1.2. CoreSight* Debug Components 1.3. Interconnect 1.4. FPGA Bridges 1.5. Memory Controllers 1.6. Support Peripherals 1.7. Introduction to the HPS Component Revision History
1.6. Support Peripherals x
1.6.1. Interface Peripherals 1.6.2. On-Chip Memories
2. Configuring the Intel® Stratix® 10 Hard Processor System Component x
2.1. Parameterizing the HPS Component 2.2. FPGA Interfaces 2.3. HPS Clocks and Resets 2.4. SDRAM 2.5. I/O Delays 2.6. Pin MUX and Peripherals 2.7. Generating and Compiling the HPS Component 2.8. Using the Address Span Extender Component 2.9. Configuring the HPS Component Revision History
2.2. FPGA Interfaces x
2.2.1. General Interfaces 2.2.2. HPS-FPGA AXI Bridges 2.2.3. HPS Boot Source 2.2.4. DMA Controller Interface 2.2.5. Interrupts
2.2.1. General Interfaces x
2.2.1.1. Enable MPU Standby and Event Interfaces 2.2.1.2. Enable General Purpose Signals 2.2.1.3. Enable Debug APB Interface 2.2.1.4. Enable System Trace Macrocell (STM) Hardware Events 2.2.1.5. Enable FPGA Cross Trigger Interface 2.2.1.6. Enable DDR ARM Trace Bus (ATB)
2.2.2. HPS-FPGA AXI Bridges x
2.2.2.1. FPGA-to-HPS Slave Interface 2.2.2.2. HPS to FPGA AXI-4 Master Interface 2.2.2.3. Lightweight HPS to FPGA Master Interface 2.2.2.4. FPGA-to-HPS SDRAM AXI* -4 Slave Interface
2.2.5. Interrupts x
2.2.5.1. FPGA-to-HPS 2.2.5.2. HPS-to-FPGA
2.3. HPS Clocks and Resets x
2.3.1. Input Clocks 2.3.2. Internal Clocks and Output Clocks 2.3.3. Resets
2.3.1. Input Clocks x
2.3.1.1. External Clock Source 2.3.1.2. FPGA-to-HPS Clocks Source 2.3.1.3. Peripheral FPGA Clocks
2.3.2. Internal Clocks and Output Clocks x
2.3.2.1. Main PLL Output Clocks – Desired Frequencies 2.3.2.2. HPS to FPGA User Clocks 2.3.2.3. HPS Peripheral Clocks – Desired Frequencies 2.3.2.4. Clock Sources 2.3.2.5. PLL Report
2.6. Pin MUX and Peripherals x
2.6.1. Auto-Place IP 2.6.2. Advanced
3. Simulating the Intel® Stratix® 10 HPS Component x
3.1. Simulation Flows 3.2. Clock and Reset Interfaces 3.3. FPGA-to-HPS AXI* Slave Interface 3.4. HPS-to-FPGA AXI* Master Interface 3.5. Lightweight HPS-to-FPGA AXI* Master Interface 3.6. HPS-to-FPGA MPU Event Interface 3.7. Interrupts Interface 3.8. HPS-to-FPGA Debug APB Interface 3.9. FPGA-to-HPS System Trace Macrocell Hardware Event Interface 3.10. HPS-to-FPGA Cross-Trigger Interface 3.11. HPS-to-FPGA Trace Port Interface 3.12. FPGA-to-HPS DMA Handshake Interface 3.13. General Purpose Input Interface 3.14. EMIF Conduit 3.15. Simulating the HPS Component Revision History
3.1. Simulation Flows x
3.1.1. Setting Up the HPS Component for Simulation 3.1.2. Generating the HPS Simulation Model in Platform Designer 3.1.3. Running the Simulations
3.1.1. Setting Up the HPS Component for Simulation x
3.1.1.1. HPS Conduit Interfaces Connecting to the FPGA
3.1.3. Running the Simulations x
3.1.3.1. Running HPS RTL Simulation 3.1.3.2. Running HPS Post-Fit Simulation
3.1.3.2. Running HPS Post-Fit Simulation x
3.1.3.2.1. Post-Fit Simulation Files 3.1.3.2.2. BFM API Hierarchy Format
3.2. Clock and Reset Interfaces x
3.2.1. Clock Interface 3.2.2. Reset Interface
1. Introduction to the Intel® Stratix® 10 Hard Processor System Component
2. Configuring the Intel® Stratix® 10 Hard Processor System Component
3. Simulating the Intel® Stratix® 10 HPS Component

3.1.3.2. Running HPS Post-Fit Simulation

To run HPS post-fit simulation after successful Platform Designer generation, perform the following steps:

  1. Add the generated synthesis file set to your Intel® Quartus® Prime project by performing the following steps:
    1. In the Intel® Quartus® Prime software, click Settings in the Assignments menu.
    2. In the Settings <your Platform Designer system name> dialog box, on the Files tab, browse to <your project directory>/<your Platform Designer system name> /synthesis/ and select <your Platform Designer system name> .qip.
    3. Click Open. The Select File dialog box closes.
    4. Click OK. The Settings dialog box closes.
  2. Optionally instantiate your HPS system as the top-level entity in your Intel® Quartus® Prime project.
  3. Compile the design by clicking Start Compilation in the Processing menu.
  4. Change the EDA Netlist Writer settings, if necessary, by performing the following steps:
    1. Click Settings in the Assignment menu.
    2. On the Simulation tab, under the EDA Tool Settings tab, you can specify the following EDA Netlist Writer settings:
      • Tool name—The name of the simulation tool
      • Format for output netlist
      • Output directory
    3. Click OK.
  5. To create the post-fitter simulation model with Intel® Quartus® Prime EDA Netlist Writer, perform the following steps:
    1. Click Start in the Processing menu.
    2. Click Start EDA Netlist Writer.

Section Content
Post-Fit Simulation Files
BFM API Hierarchy Format

Related Information
Level Two Title