F-Tile CPRI PHY Intel® FPGA IP User Guide

Download PDF
ID 683284
Date 6/21/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the F-Tile CPRI PHY Intel® FPGA IP Core 2. Getting Started 3. IP Parameter Settings 4. Functional Description 5. Interface Signals 6. IP Registers 7. F-Tile CPRI PHY Intel FPGA IP User Guide Archives 8. Document Revision History for the F-Tile CPRI PHY Intel FPGA IP User Guide
1. About the F-Tile CPRI PHY Intel® FPGA IP Core x
1.1. Supported Features 1.2. Overview 1.3. Device Family Support 1.4. Device Speed Grade Support 1.5. Resource Utilization 1.6. Release Information
2. Getting Started x
2.1. Installing and Licensing Intel® FPGA IP Cores 2.2. Specifying the IP Core Parameters and Options 2.3. Generated File Structure 2.4. IP Core Testbenches
2.1. Installing and Licensing Intel® FPGA IP Cores x
2.1.1. Intel® FPGA IP Evaluation Mode
2.2. Specifying the IP Core Parameters and Options x
2.2.1. Reference and System PLL Clock for your IP Design
4. Functional Description x
4.1. Reset Logic 4.2. Latency Measurement
4.2. Latency Measurement x
4.2.1. Deterministic Latency 4.2.2. Calculation for 64b/66b Datapath
5. Interface Signals x
5.1. Clock Signals 5.2. Reset Signals 5.3. TX MII Interface (64b/66b) 5.4. RX MII Interface (64b/66b) 5.5. Status Interface for 64b/66b Line Rate 5.6. TX Interface (8b/10b) 5.7. RX Interface (8b/10b) 5.8. Status Interface for 8b/10b Line Rate 5.9. Serial Interface 5.10. CPRI PHY Reconfiguration Interface 5.11. Datapath Avalon Memory-Mapped Interface 5.12. PMA Avalon Memory-Mapped Interface
5.1. Clock Signals x
5.1.1. Required Clock Frequencies
1. About the F-Tile CPRI PHY Intel® FPGA IP Core
2. Getting Started
3. IP Parameter Settings
4. Functional Description
5. Interface Signals
6. IP Registers
7. F-Tile CPRI PHY Intel FPGA IP User Guide Archives
8. Document Revision History for the F-Tile CPRI PHY Intel FPGA IP User Guide

5.3. TX MII Interface (64b/66b)

Table 19.  TX MII Interface
Port Name Width (Bits) Domain Description
i_tx_mii_d[63:0] 64 o_tx_clkout2

TX MII data. Data must be in MII encoding. i_tx_mii_d[7:0] holds the first byte that the IP core transmits on the CPRI link. i_tx_mii_d[0] holds the first bit the IP core transmits on the CPRI link.

i_tx_mii_c[7:0] 8 o_tx_clkout2 TX MII control bits. Each bit corresponds to a byte of the TX MII data signal. For example, i_tx_mii_c[0] corresponds to i_tx_mii_d[7:0], i_tx_mii_c[1] corresponds to i_tx_mii_d[15:8], and so on.

If the value of a bit is 1, the corresponding data byte is a control byte. If the value of a bit is 0, the corresponding data byte is data.

The Start of Packet byte (0xFB) and End of Packet byte (0xFD) are control bytes.

Figure 8. Transmitting Data Using TX MII InterfaceThis figure shows how to write packets directly to the TX MII interface.
  • The packets are written using MII. Each byte in i_tx_mii_d has a corresponding bit in i_tx_mii_c that indicates whether the byte is a control byte or a data byte; for example, i_tx_mii_c[1] is the control bit for i_tx_mii_d[15:8].
  • The byte order for the TX MII interface flows from right to left; the first byte to be transmitted from the interface is i_tx_mii_d[7:0].
  • The first bit to be transmitted from the interface is i_tx_mii_d[0].
Level Two Title