F-Tile Avalon® Streaming Intel® FPGA IP for PCI Express* User Guide

Download PDF
ID 683140
Date 1/26/2024
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Acronyms 2. Introduction 3. IP Architecture and Functional Description 4. Advanced Features 5. Interfaces 6. Parameters 7. Testbench 8. Troubleshooting/Debugging 9. F-Tile Avalon Streaming Intel FPGA IP for PCI Express User Guide Archives 10. Revision History for the F-Tile Avalon Streaming Intel FPGA IP for PCI Express User Guide A. Configuration Space Registers B. Implementation of Address Translation Services (ATS) in Endpoint Mode C. Packets Forwarded to the User Application in TLP Bypass Mode D. Root Port Enumeration E. Bifurcated Endpoint Support for Independent Resets
2. Introduction x
2.1. Overview 2.2. Features 2.3. Release Information 2.4. Device Family Support 2.5. Performance and Resource Utilization 2.6. IP Core and Design Example Support Levels
3. IP Architecture and Functional Description x
3.1. Architecture 3.2. Functional Description 3.3. Avalon-ST TX/RX 3.4. Interrupts 3.5. Completion Timeout 3.6. Hot Plug 3.7. Power Management 3.8. Configuration Output Interface (COI) 3.9. Configuration Intercept Interface (EP Only) 3.10. Hard IP Reconfiguration Interface 3.11. PHY Reconfiguration Interface 3.12. Page Request Service (PRS) (EP Only)
3.1. Architecture x
3.1.1. Clocks 3.1.2. Refclk 3.1.3. Reset
3.2. Functional Description x
3.2.1. PMA/PCS 3.2.2. Data Link Layer 3.2.3. Transaction Layer
3.3. Avalon-ST TX/RX x
3.3.1. TLP Header and Data Alignment 3.3.2. Avalon-ST RX 3.3.3. Avalon-ST TX 3.3.4. Tag Allocation 3.3.5. Completion Buffer Size
3.3.2. Avalon-ST RX x
3.3.2.1. RX Flow Control
3.3.3. Avalon-ST TX x
3.3.3.1. TX Flow Control
3.4. Interrupts x
3.4.1. Legacy Interrupts 3.4.2. MSI 3.4.3. MSI-X
3.10. Hard IP Reconfiguration Interface x
3.10.1. Configuration Registers Access
3.10.1. Configuration Registers Access x
3.10.1.1. Direct User Avalon-MM Interface (Byte Access) 3.10.1.2. Debug Register Interface Access (Dword Access)
4. Advanced Features x
4.1. Virtualization Support 4.2. TLP Bypass Mode 4.3. Precision Time Measurement (PTM) 4.4. Scalable IOV
4.1. Virtualization Support x
4.1.1. Single Root I/O Virtualization (SR-IOV) 4.1.2. VirtIO
4.1.1. Single Root I/O Virtualization (SR-IOV) x
4.1.1.1. SR-IOV Implementation
4.1.1.1. SR-IOV Implementation x
4.1.1.1.1. Functional Level Reset (FLR)
4.1.2. VirtIO x
4.1.2.1. VirtIO Implementation 4.1.2.2. VirtIO Registers
4.2. TLP Bypass Mode x
4.2.1. Register Settings for TLP Bypass mode 4.2.2. Avalon-MM usage for TLP Bypass Mode 4.2.3. Transmit Interface 4.2.4. Receive Interface 4.2.5. Configuration TLP 4.2.6. Malformed TLP 4.2.7. ECRC
4.2.1. Register Settings for TLP Bypass mode x
4.2.1.1. TLPBYPASS_ERR_EN (Address 0x14194) 4.2.1.2. TLPBYPASS_ERR_STATUS (Address 0x14190)
5. Interfaces x
5.1. Overview 5.2. Clocks and Resets 5.3. Serial Data Interface 5.4. Avalon-ST Interface 5.5. Interrupt Interface 5.6. Hard IP Status Interface 5.7. Error Interface 5.8. 10-bit Tag Support Interface 5.9. Completion Timeout Interface 5.10. Power Management Interface 5.11. Hot Plug Interface (RP Only) 5.12. Configuration Output Interface 5.13. Configuration Intercept Interface (EP Only) 5.14. Hard IP Reconfiguration Interface 5.15. PHY Reconfiguration Interface 5.16. Page Request Service (PRS) Interface (EP Only) 5.17. FLR Interface Signals 5.18. PTM Interface Signals 5.19. VF Error Flag Interface Signals 5.20. VirtIO PCI Configuration Access Interface Signals
5.4. Avalon-ST Interface x
5.4.1. Avalon-ST RX Interface Signals 5.4.2. Avalon-ST TX Interface Signals
5.5. Interrupt Interface x
5.5.1. Legacy Interrupt Interface Signals 5.5.2. MSI Pending Bits Interface Signals
6. Parameters x
6.1. Top-Level Settings 6.2. Core Parameters
6.2. Core Parameters x
6.2.1. Avalon Parameters 6.2.2. Base Address Registers 6.2.3. PCI Express and PCI Capabilities Parameters 6.2.4. Device Identification Registers 6.2.5. Configuration, Debug and Extension Options 6.2.6. Analog Options
6.2.3. PCI Express and PCI Capabilities Parameters x
6.2.3.1. Device Capabilities 6.2.3.2. Link Capabilities 6.2.3.3. Legacy Interrupt Pin Register 6.2.3.4. MSI Capabilities 6.2.3.5. MSI-X Capabilities 6.2.3.6. Slot Capabilities 6.2.3.7. Latency Tolerance Reporting (LTR) 6.2.3.8. Process Address Space ID (PASID) 6.2.3.9. Device Serial Number Capability 6.2.3.10. Page Request Service (PRS) 6.2.3.11. Access Control Service (ACS) Capabilities 6.2.3.12. Power Management 6.2.3.13. Vendor Specific Extended Capability (VSEC) Registers 6.2.3.14. Precision Time Measurement (PTM) 6.2.3.15. Address Translation Services (ATS) 6.2.3.16. TLP Processing Hints (TPH) 6.2.3.17. VirtIO Parameters 6.2.3.18. Receiver Detection
7. Testbench x
7.1. FASTSIM Mode Support 7.2. Generating Tile Files 7.3. Endpoint Testbench 7.4. Test Driver Module 7.5. Root Port BFM 7.6. BFM Procedures and Functions 7.7. PIPE Mode Simulation
7.5. Root Port BFM x
7.5.1. BFM Memory Map 7.5.2. Configuration Space Bus and Device Numbering 7.5.3. Configuration of Root Port and Endpoint 7.5.4. Issuing Read and Write Transactions to the Application Layer
7.6. BFM Procedures and Functions x
7.6.1. ebfm_barwr Procedure 7.6.2. ebfm_barwr_imm Procedure 7.6.3. ebfm_barrd_wait Procedure 7.6.4. ebfm_barrd_nowt Procedure 7.6.5. ebfm_cfgwr_imm_wait Procedure 7.6.6. ebfm_cfgwr_imm_nowt Procedure 7.6.7. ebfm_cfgrd_wait Procedure 7.6.8. ebfm_cfgrd_nowt Procedure 7.6.9. BFM Configuration Procedures 7.6.10. BFM Shared Memory Access Procedures 7.6.11. BFM Log and Message Procedures 7.6.12. Verilog HDL Formatting Functions
7.6.9. BFM Configuration Procedures x
7.6.9.1. ebfm_cfg_rp_ep Procedure 7.6.9.2. ebfm_cfg_decode_bar Procedure
7.6.10. BFM Shared Memory Access Procedures x
7.6.10.1. Shared Memory Constants 7.6.10.2. shmem_write Task 7.6.10.3. shmem_read Function 7.6.10.4. shmem_display Verilog HDL Function 7.6.10.5. shmem_fill Procedure 7.6.10.6. shmem_chk_ok Function
7.6.11. BFM Log and Message Procedures x
7.6.11.1. ebfm_display Verilog HDL Function 7.6.11.2. ebfm_log_stop_sim Verilog HDL Function 7.6.11.3. ebfm_log_set_suppressed_msg_mask Task 7.6.11.4. ebfm_log_set_stop_on_msg_mask Verilog HDL Task 7.6.11.5. ebfm_log_open Verilog HDL Function 7.6.11.6. ebfm_log_close Verilog HDL Function
7.6.12. Verilog HDL Formatting Functions x
7.6.12.1. himage1 7.6.12.2. himage2 7.6.12.3. himage4 7.6.12.4. himage8 7.6.12.5. himage16 7.6.12.6. dimage1 7.6.12.7. dimage2 7.6.12.8. dimage3 7.6.12.9. dimage4 7.6.12.10. dimage5 7.6.12.11. dimage6 7.6.12.12. dimage7
7.7. PIPE Mode Simulation x
7.7.1. PIPE Mode Clock Signal 7.7.2. PIPE Mode Reset Signal To Verification IP (VIP)
8. Troubleshooting/Debugging x
8.1. Hardware 8.2. Debug Toolkit
8.1. Hardware x
8.1.1. Debugging Link Training Issues 8.1.2. Debugging Data Transfer and Performance Issues
8.1.1. Debugging Link Training Issues x
8.1.1.1. Generic Tools and Utilities 8.1.1.2. Signal Tap II Logic Analyzer 8.1.1.3. Additional Debug Tools
8.1.1.3. Additional Debug Tools x
8.1.1.3.1. Using the Hard IP Reconfiguration Interface 8.1.1.3.2. Enable and Read LCRC and ECRC Error Count
8.1.2. Debugging Data Transfer and Performance Issues x
8.1.2.1. Advanced Error Reporting (AER) 8.1.2.2. Second-Level Debug Tools
8.2. Debug Toolkit x
8.2.1. Overview 8.2.2. Enabling the F-Tile Debug Toolkit 8.2.3. Launching the F-Tile Debug Toolkit 8.2.4. Using the F-Tile Debug Toolkit 8.2.5. Using the F-Tile Link Inspector
8.2.4. Using the F-Tile Debug Toolkit x
8.2.4.1. Main View 8.2.4.2. Toolkit Parameters 8.2.4.3. Channel Parameters 8.2.4.4. Eye Viewer
8.2.4.2. Toolkit Parameters x
8.2.4.2.1. F-Tile Information 8.2.4.2.2. Event Counter 8.2.4.2.3. P0/P1 Configuration Space
8.2.4.3. Channel Parameters x
8.2.4.3.1. General PHY 8.2.4.3.2. TX Path 8.2.4.3.3. RX Path
A. Configuration Space Registers x
A.1. Configuration Space Registers A.2. Configuration Space Registers for Virtualization A.3. Intel-Defined VSEC Capability Registers
A.1. Configuration Space Registers x
A.1.1. Register Access Definitions A.1.2. PCIe Configuration Header Registers A.1.3. PCI Express Capability Structures A.1.4. Physical Layer 16.0 GT/s Extended Capability Structure A.1.5. MSI-X Registers
A.2. Configuration Space Registers for Virtualization x
A.2.1. SR-IOV Virtualization Extended Capabilities Registers Address Map A.2.2. PCIe Configuration Registers for Each Virtual Function
A.2.2. PCIe Configuration Registers for Each Virtual Function x
A.2.2.1. Alternative Routing ID (ARI) Capability Structure A.2.2.2. TLP Processing Hint (TPH) Capability Structure A.2.2.3. Address Translation Services (ATS) Capability Structure A.2.2.4. Access Control Services (ACS) Capability Structure
A.2.2.1. Alternative Routing ID (ARI) Capability Structure x
A.2.2.1.1. ARI Enhanced Capability Header Register (Offset 0x0) A.2.2.1.2. ARI Capability and Control Register (Offset 0x4)
A.2.2.2. TLP Processing Hint (TPH) Capability Structure x
A.2.2.2.1. TPH Requester Enhanced Capability Header (Offset 0x0) A.2.2.2.2. TPH Requester Capability Register (Offset 0x4) A.2.2.2.3. TPH Requester Control Register (Offset 0x8)
A.2.2.3. Address Translation Services (ATS) Capability Structure x
A.2.2.3.1. ATS Enhanced Capability Header (Offset 0x0) A.2.2.3.2. ATS Capability Register and ATS Control Register (Offset 0x4)
A.2.2.4. Access Control Services (ACS) Capability Structure x
A.2.2.4.1. ACS Extended Capability Header (Offset 0x0) A.2.2.4.2. ACS Capability Register (Offset 0x4) A.2.2.4.3. ACS Control Register (Offset 0x6) A.2.2.4.4. Egress Control Vector (Offset 0x8)
A.3. Intel-Defined VSEC Capability Registers x
A.3.1. Intel-Defined VSEC Capability Header (Offset 00h) A.3.2. Intel-Defined Vendor Specific Header (Offset 04h) A.3.3. Intel Marker (Offset 08h) A.3.4. JTAG Silicon ID (Offset 0x0C - 0x18) A.3.5. User Configurable Device and Board ID (Offset 0x1C - 0x1D) A.3.6. General Purpose Control and Status Register (Offset 0x30) A.3.7. Uncorrectable Internal Error Status Register (Offset 0x34) A.3.8. Uncorrectable Internal Error Mask Register (Offset 0x38) A.3.9. Correctable Internal Error Status Register (Offset 0x3C) A.3.10. Correctable Internal Error Mask Register (Offset 0x40)
B. Implementation of Address Translation Services (ATS) in Endpoint Mode x
B.1. Sending Translated/Untranslated Requests B.2. Sending a Page Request Message from the Endpoint (EP) to the Root Complex (RC) B.3. Invalidating Requests/Completions
C. Packets Forwarded to the User Application in TLP Bypass Mode x
C.1. EP TLP Bypass Mode (Upstream) C.2. RC TLP Bypass Mode (Downstream)
E. Bifurcated Endpoint Support for Independent Resets x
E.1. PCI Express Resets E.2. Supported Configurations
E.2. Supported Configurations x
E.2.1. Configuration Type A E.2.2. Configuration Type B E.2.3. Configuration Type C
1. Acronyms
2. Introduction
3. IP Architecture and Functional Description
4. Advanced Features
5. Interfaces
6. Parameters
7. Testbench
8. Troubleshooting/Debugging
9. F-Tile Avalon Streaming Intel FPGA IP for PCI Express User Guide Archives
10. Revision History for the F-Tile Avalon Streaming Intel FPGA IP for PCI Express User Guide
A. Configuration Space Registers
B. Implementation of Address Translation Services (ATS) in Endpoint Mode
C. Packets Forwarded to the User Application in TLP Bypass Mode
D. Root Port Enumeration
E. Bifurcated Endpoint Support for Independent Resets

8.1.2. Debugging Data Transfer and Performance Issues

There are many possible reasons causing the PCIe link to stop transmitting data. The PCI Express base specification defines three types of errors, outlined in the table below:

Table 117.  Error Types Defined by the PCI Express Base Specification
Type Responsible Agent Description
Correctable Hardware While correctable errors may affect system performance, data integrity is maintained.
Uncorrectable, non-fatal Device software Uncorrectable, non-fatal errors are defined as errors in which data is lost, but system integrity is maintained. For example, the fabric may lose a particular TLP, but it still works without problems.
Uncorrectable, fatal System software Errors generated by a loss of data and system failure are considered uncorrectable and fatal. Software must determine how to handle such errors: whether to reset the link or implement other means to minimize the problem.
Table 118.  Correctable Error Status Register (AER)
Observation Issue Resolution
Receiver error bit set

Physical layer error which may be due to a PCS error when a lane is in L0, or a Control symbol being received in the wrong lane, or signal Integrity issues where the link may transition from L0 to the Recovery state.

Use the configuration output interface, or the Hard IP reconfiguration interface and the flow chart in Debugging Link Training Issues to obtain more information about the error.
Bad DLLP bit set

Data link layer error which may occur when a CRC verification fails.

Use the configuration output interface or the Hard IP reconfiguration interface to obtain more information about the error.
Bad TLP bit set Data link layer error which may occur when an LCRC verification fails or when a sequence number error occurs. Use the configuration output interface or the Hard IP reconfiguration interface to obtain more information about the error.
Replay_num_rollover bit set Data link layer error which may be due to TLPs sent without success (no ACK) four times in a row. Use the configuration output interface or the Hard IP reconfiguration interface to obtain more information about the error.
replay timer timeout status bit set

Data link layer error which may occur when no ACK or NAK was received within the timeout period for the TLPs transmitted.

Use the configuration output interface or the Hard IP reconfiguration interface to obtain more information about the error.
Corrected internal error bits set Transaction layer error which may be due to an ECC error in the internal Hard IP RAM. Use the error interface, configuration output interface, or the Hard IP reconfiguration interface and DBI registers to obtain more information about the error.
Table 119.  Uncorrectable Error Status Register (AER)
Observation Issue Resolution
Data link protocol error Data link layer error which may be due to transmitter receiving an ACK/NAK whose Seq ID does not correspond to an unacknowledged TLP or ACK sequence number. Use the configuration output interface, Hard IP reconfiguration interface to obtain more information about the error.
Surprise down error Data link layer error which may be due to link_up_o getting deasserted during L0, indicating the physical layer link is going down unexpectedly. Use the error interface, configuration output interface, Hard IP reconfiguration interface and DBI registers to obtain more information about the error.
Flow control protocol error

Transaction layer error which can be due to the receiver reporting more than the allowed credit limit.

This error occurs when a component does not receive updated flow control credits with the 200 μs limit.

Use the TX/RX flow control interface, configuration output interface, Hard IP reconfiguration interface to obtain more information about the error.
Poisoned TLP received Transaction layer error which can be due to a received TLP with the EP bit set. Use the error interface, configuration output interface, configuration intercept interface, Hard IP reconfiguration interface to obtain more information on the error and determine the appropriate action.
Completion timeout Transaction layer error which can be due to a completion not received within the required amount of time after a non-posted request was sent. Use the error interface, completion timeout interface, configuration output interface, Hard IP reconfiguration interface to obtain more information on the error.
Completer abort Transaction layer error which can be due to a completer being unable to fulfill a request due to a problem with the requester or a failure of the completer. Use the configuration output interface, error interface, Hard IP reconfiguration interface to obtain more information on the error.
Unexpected completion

Transaction layer error which can be due to a requester receiving a completion that doesn’t match any request awaiting a completion.

The TLP is deleted by the Hard IP and not presented to the Application Layer.

Use the configuration output interface, error interface, Hard IP reconfiguration interface to obtain more information on the error.
Receiver overflow

Transaction layer error which can be due to a receiver receiving more TLPs than the available receive buffer space.

The TLP is deleted by the Hard IP and not presented to the Application Layer.

Use the TX/RX flow control interface, error interface, configuration output interface, Hard IP reconfiguration interface to obtain more information on the error.
Malformed TLP

Transaction layer error which can be due to errors in the received TLP header.

The TLP is deleted by the Hard IP and not presented to the Application Layer.

Use the error interface, configuration output interface, Hard IP reconfiguration interface to obtain more information on the error.
ECRC error

Transaction layer error which can be due to an ECRC check failure at the receiver despite the fact that the TLP is not malformed and the LCRC check is valid.

The Hard IP block handles this TLP automatically. If the TLP is a non-posted request, the Hard IP block generates a completion with a completer abort status. The TLP is deleted by the Hard IP and not presented to the Application Layer.

Use the configuration output interface, Hard IP reconfiguration interface to obtain more information on the error.
Unsupported request

Transaction layer error which can be due to the completer being unable to fulfill the request.

The TLP is deleted in the Hard IP block and not presented to the Application Layer. If the TLP is a non-posted request, the Hard IP block generates a completion with Unsupported Request status.

Use the configuration output interface, error interface, Hard IP reconfiguration interface to obtain more information on the error.
ACS violation Transaction layer error which can be due to access control error in the received posted or non-posted request. Use the configuration output interface, error interface, Hard IP reconfiguration interface to obtain more information on the error.
Uncorrectable internal error Transaction layer error which can be due to an internal error that cannot be corrected by the hardware. Use the error interface, configuration output interface, Hard IP reconfiguration interface and DBI registers to obtain more information on the error.
TLP prefix blocked EP or RP only Use the error interface, configuration output interface, Hard IP reconfiguration interface to obtain more information on the error.
Poisoned TLP egress blocked EP or RP only Use the error interface, configuration output interface, configuration intercept interface, Hard IP reconfiguration interface to obtain more information on the error.

Use the debug tools mentioned in the next two sections for debugging link training issues observed on the PCI Express link when using the F-Tile Avalon® -ST IP for PCI Express.


Section Content
Advanced Error Reporting (AER)
Second-Level Debug Tools

Related Information
Level Two Title