Introduction
Development Kit
| IP Core | IP Core Category |
|---|---|
| Top level generated instrumentation fabric | Debug & Performance |
| Altera Arria 10 XCVR Reset Sequencer | Other |
| Nios II Gen2 Processor | NiosII |
| Nios II Gen2 Processor Unit | NiosII |
| On-Chip Memory (RAM or ROM) | OnChipMemory |
| Arria 10 External Memory Interfaces | ExternalMemoryInterfaces |
| EMIF Core Component for 20nm Families | ExternalMemoryInterfaces |
| EMIF Error Correction Code (ECC) Component | Internal Components |
| EMIF Error Correction Code (ECC) Component for Arria 10 | Internal Components |
| Arria 10 External Memory Interfaces Debug Component | ExternalMemoryInterfaces |
| alt_mem_if JTAG to Avalon Master Bridge | BridgesAndAdaptors |
| Avalon-ST JTAG Interface | QsysInterconnect |
| Avalon-ST Packets to Bytes Converter | QsysInterconnect |
| Avalon-ST Channel Adapter | QsysInterconnect |
| Avalon Packets to Transaction Converter | QsysInterconnect |
| Avalon-ST Timing Adapter | QsysInterconnect |
| Avalon-ST Single Clock FIFO | QsysInterconnect |
| Reset Controller | QsysInterconnect |
| Avalon-ST Bytes to Packets Converter | QsysInterconnect |
| MM Interconnect | QsysInterconnect |
| Avalon-MM Master Translator | QsysInterconnect |
| Avalon-MM Slave Translator | QsysInterconnect |
| Avalon-MM Pipeline Bridge | QsysInterconnect |
| JTAG UART | ConfigurationProgramming |
| System ID Peripheral | Other |
| Clocked Video Input II (4K Ready) | AudioVideo |
| Video and Image Processing Suite | Other |
| Clocked Video Output II (4K Ready) | AudioVideo |
| Video Input Bridge | AudioVideo |
| alt_vip_cvo_core | AudioVideo |
| Switch II (4K Ready) | Video and Image Processing |
| Frame Buffer II (4K Ready) | AudioVideo |
| Interval Timer | Peripherals |
| Memory-Mapped Demultiplexer | QsysInterconnect |
| Memory-Mapped Multiplexer | QsysInterconnect |
| Avalon-ST Handshake Clock Crosser | QsysInterconnect |
| Avalon-MM Master Agent | QsysInterconnect |
| Avalon-MM Slave Agent | QsysInterconnect |
| Memory-Mapped Router | QsysInterconnect |
| IRQ Mapper | QsysInterconnect |
| IRQ Clock Crosser | QsysInterconnect |
| ALTCLKCTRL | ClocksPLLsResets |
| Arria 10 Transceiver Native PHY | TransceiverPHY |
| Transceiver PHY Reset Controller | TransceiverPHY |
| SDI II | TransceiverPHY |
| Arria 10 FPLL | ClocksPLLsResets |
| Altera IOPLL | ClocksPLLsResets |
Detailed Description
Prepare the design template in the Quartus Prime software GUI (version 14.1 and later)
Note: After downloading the design example, you must prepare the design template. The file you downloaded is of the form of a <project>.par file which contains a compressed version of your design files (similar to a .qar file) and metadata describing the project. The combination of this information is what constitutes a <project>.par file. In releases 16.0 or newer, you can simply double click on the <project>.par file and Quartus will launch that project.
The second means to bring up the project template is through the New Project Wizard (File -> New Project Wizard). After entering the project name and folder on the first panel, the second panel will ask you to specify an empty project or project template. Select project template. You will see a list of Design Templates projects that you have loaded prior as well as various "Baseline Pinout Designs" that contain the pinout and settings for a variety of development kits. If you don't see your design template in the list, click on the link that states install the Design Templates circled below:
Browse to the <project>.par file you downloaded, click next, followed by Finish, and your design template will be installed and displayed in the Project Navigator pane in Quartus.
Note: When a design is stored in the Design Store as a design template, it has been previously regression tested against the stated version of Quartus software. The regression ensures the design template passes analysis/synthesis/fitting/assembly steps in the Quartus design flow.
Prepare the design template in the Quartus Prime software command-line
At the command-line, type the following command:
quartus_sh --platform_install -package <project directory>/<project>.par
Once the process completes, then type:
quartus_sh --platform -name <project>
Note:
* ACDS Version: 19.2.0 Pro